Capital Prospect GS101 Garage Door Sensor (Transmitter) User Manual
Capital Prospect Ltd Garage Door Sensor (Transmitter)
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 578077 |
| Application ID | tDdzTQ7R57wY2qEwmSUkKg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 8.07kB (100855 bits) |
| Date Submitted | 2005-09-03 00:00:00 |
| Date Available | 2005-09-03 00:00:00 |
| Creation Date | 2005-07-15 10:42:11 |
| Document Lastmod | 2005-07-15 10:42:37 |
| Document Title | User Manual |
| Document Creator | HP 9100C Digital Sender |
| Document Author: | BEN HO |
Garage Door Monitor” Sensor nodetcs-toi 1 lNTRODUCTlON The garage door monitorm sensor is designed to monitor the status or your garage door and advise you it the door is open By placing the sensor on the door panel, you will be alerted when the door is open When the garage door is open, reoe'wer will beep and trash In this package, you should find a garage door momtor” sensor, 3V lithium batlery, doublersided loam tape, mounting accessories and a 0le iv trortrnri a» pan n' W car-ago door ‘ dm 3 ii 1! MM rilonitor‘" s-nm tPchS‘ch Please lollow the instructions below to set up your garage door monitorw sensor properly 2 SET UP THEGARAGE DOORSENSOR To program the sensor to the Control Parle|AM-001 1, Press the [FROG] button on the side at the control panel, the [PROG] LED will light on. Enter the current MFIN [default 1234] Enter [3] Select a zone and sensor location to program the sensor to Activate the sensor, the control panel will beep and you will hear “Zone 5 Sensor 5 Accepted it the sensor is were grammed The [FROG] LED wrll be off 6 To program other sensor, repeat the above steps. may» Notes ll an occupied sensor location is Selected, the new sensor will replace the old one, 3. POWER UP THE GARAGE DOOR MONITOR SENSOR After setting up all the connectors, the sensor is ready to be powered up. Push the detection rod to it's fully retracted position. lnsel‘t the 3V lithium battery to the sensor as shown in the diagram lnnrt av mwtotht "nut ll the detection rod on the sensor is fully extended, one of the red LED on the receiver will flash and beep You can install the sensor onto the garage door Detection Detection rod ll fully rodls rutry retracted eiriended lNSTALLAllON Unplug the power cord or your garage door opener oerore installation to ensure power is not connected Step 1 — Select a spot on your garage door to mount the sensor Beloro you install the sensor onto the garage door, make sure the garage door is closed The sensor assembly should be mounted on one or the vertical supports or your garage door near the bottom. When the door ls Closed, the detedion rod should be retracted When lhe door Is open the detection rod will be extended. Dswclolnd now open 5. OPERATION When the garage door is open, the sensor will send a signal to the receiver, it will beep and the corresponding zone red LED will flash 5 FCC This device complies with Part is or the FCC Rules Dperahort ia subtect lo the lollowing Mo conditions (1) This device may not cause liarmrul lnterterehce. and (2) This device must accept any inlerterenoe received. including interterence that may cause undesired operation WARNING: Changes or modrncatione to this unit not expressly approved by the party responsible tor compliance could void the user‘s authority to openna the equipment NOTE: This eqmpment has been tested and round to comply wtth the limits tor a Class B dignal device, pursuant to Part 15 ol the Fcc Rules These Ilmtls are designed to provide reasonable protection against harmful tnterterence in a residential installation This equipment generates, uses and can radiate radio irequency energy and, it not installed and used in accordance with the instructions. may cause harmtul inter— telenoe to radio communications however, there is no guarantee that interterence Will not occur in a particular installation It this equipment dose muse harmful tnterterence to radio or television emotion, whim can be determrned by turning the equipment otrand on, lhe user is encouraged to try to correct the lnlerterence by one or more or the ramming measures , Reolleht or relocate the receiving antenna - Increase the separation between the equipment and receiver , Connect the equipment into an outlet on a circuit dinerenl item that to which the reoerver is connected ~ Consult the dealer or an experienced radio/TV technician lor help 7. WARRANTY ll, wrthrn one year lrdrrr date or purchase, this product should become detective (except battery), due to rauity workmanship or materials. it will be repaired or replaced, writioul charge Proof or purchase and a Return Arthurizalion are required, BC OMERSERWCE It you would Ilke to order Skylihk‘s products or have dlmmlty getting them to work, please i visit our FAQ search at W§Mmkhomemm or 2 email us at su k ink ome com. or 3 all our toll tree at 14004044167 trorn Monday to Friday 9 am to 5 pm EST Fax (soul zssetazo CUSTOMER SERVICE t7 sneard Avenue. Brampton, Ohtarlo, Canada Lev us Email aupport@skylrnlrhome coin hrip lrwww skyllhkhume com P/N tutAxxx RWD US PIIUIE.597,291 ©2006 SKVLINK GROUP
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-701 Modify Date : 2005:07:15 10:42:37+08:00 Create Date : 2005:07:15 10:42:11+08:00 Metadata Date : 2005:07:15 10:42:37+08:00 Creator Tool : HP 9100C Digital Sender Format : application/pdf Creator : BEN HO Document ID : uuid:410e0553-cc36-4481-ad6d-7349bfd75f26 Instance ID : uuid:47080cc9-8ffa-42f2-bb50-67e0efc0a498 Page Count : 1 Author : BEN HOEXIF Metadata provided by EXIF.tools