Capital Prospect MK318 KEYCHAIN TYPE TRANSMITTER User Manual MG6T2

Download:
Mirror Download [FCC.gov]
Document ID	1500526
Application ID	FcrphCupRFEoCKW0u1n1+g==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.16kB (89539 bits)
Date Submitted	2011-07-14 00:00:00
Date Available	2011-07-14 00:00:00
Creation Date	2011-07-12 12:20:22
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2011-07-12 13:12:01
Document Title	MG6T2
Document Creator	Adobe PageMaker 7.0
Document Author:	Ida

3-Button Garage Door
Remote Control
Model MK-318
1. INTRODUCTION
2c. PROGRAM A TRANSMITTER TO RECEIVER GB-318-3
®
In this package, you will find a Skylink garage door transmitter with 3V
lithium battery.
To program the transmitter to a Skylink Garage Door
Receiver Smart ButtonTM GB-318-3 (3 doors) , please
follow the user’s instruction for the model GB-318-3.
Garage Door
Transmitter
(Battery inside)
2d. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR
OPENER - IQ SERIES
There are three buttons on transmitter MK-318, each button can be
programed to control Skylink garage door receiver Smart ButtonTM GB-318
or GB-318-3 or Skylink garage door opener directly.
To program the transmitter to the Skylink® IQ series Garage Door Opener,
please follow the user’s instruction from the Garage Door Opener.
Follow one or more instructions below in Section 2 to program transmitter
MK-318 to the receiver or receivers you want to control.
3. TROUBLE SHOOTING
2a. PROGRAM TRANSMITTER TO RECEIVER GB-318
You need to do the programming in order to add the transmitter - remote
control to a receiver.
Refer to the receiver Smart ButtonTM GB-318 user’s instruction to set up the unit.
Smart ButtonTM GB-318 can learn up to 10 remote controls.
To program the transmitter to the receiver, follow the instructions below:
1. Press the learn button on the side of the Smart ButtonTM GB-318.
2. Once the learn button is pressed, the LED will
flash quickly. Release the learn button.
Antenna
3. Within 30 seconds, press any one of the 3 buttons
on the transmitter that you want to program to the
receiver.
4. Once the remote control is programmed, the LED
LED
will flash slowly, in the same way as it flashes
in standby mode.
Learn
5. You may now operate the garage door opener
Button
with this new remote control.
TM
6. To program this transmitter to control another
Smart Button
GB-318
receiver, repeat process (1) to (4) to program
another button on the remote control.
2b. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR
OPENER - EQ SERIES
You need to do the programming in order to add the transmitter to a
Skylink® Garage Door Opener.
Q: What can I do if the door opener does not react after I press the button on
the transmitter ?
A: - Ensure when the button on the transmitter is pressed, the red light on the
transmitter comes on. Otherwise, check if the battery is inserted properly.
- Make sure the correct button on the transmitter is pressed.
- Ensure the wires that were previously connected to the wall mounted
door control are not loose.
- Ensure the transmitter has been programmed to the receiver. Refer
to section 2 for how to program a transmitter to the receiver.
4. BATTERY
3 Volt lithium battery (CR 2032) (included).
It is time to change the battery when the red LED on the transmitter does
not turn on when either button is pressed.
5. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
6. IC
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de
brouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionmement.
7. WARRANTY
Skylink® Garage Door Opener can learn up to 16 remote controls.
To program the transmitter to the Garage Door Receiver, follow the
instructions below:
1. Press the LEARN/SET button once on the garage door opener.
2. Once the LEARN/SET buttton is pressed, the LEARN LED will flash.
You may release the LEARN/SET button.
3. Within 30 seconds, press any one of the 3 buttons on the transmitter
that you want to program to the receiver.
4. Once the transmitter is programmed, the LEARN LED will turn off.
5. You may now operate the garage door opener with this new transmitter.
6. To program a transmitter to control another garage door opener,
repeat process (1) to (4) to program another button on the transmitter.
Learn Button
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
8. CUSTOMER SERVICE
If you would like to
- find out the up-to-date specifications
- know more about features and applications
- download documents, i.e. user’s instructions
- order Skylink products
or if you have difficulty getting products to work, please:
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N : 101Z993
Patent Pending
©2010 SKYLINK GROUP

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Author                          : Ida
Create Date                     : 2011:07:12 12:20:22+08:00
Modify Date                     : 2011:07:12 13:12:01+08:00
Subject                         : MG6T2
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Keywords                        : 
Creator Tool                    : Adobe PageMaker 7.0
Metadata Date                   : 2011:07:12 13:12:01+08:00
Format                          : application/pdf
Title                           : MG6T2
Creator                         : Ida
Description                     : MG6T2
Document ID                     : uuid:83d7f83c-16ff-4a15-b21f-f3a29db921a6
Instance ID                     : uuid:b5b36dbb-b36e-46bd-b016-02e04e376720
Page Count                      : 1

EXIF Metadata provided by EXIF.tools