Capital Prospect MK318 KEYCHAIN TYPE TRANSMITTER User Manual MG6T2

Capital Prospect Ltd KEYCHAIN TYPE TRANSMITTER MG6T2

Contents

User manual

1. INTRODUCTION3-Button Garage DoorRemote Control Model MK-318In this package, you will find a Skylink® garage door transmitter with 3Vlithium battery.You need to do the programming in order to add the transmitter - remotecontrol to a receiver.Refer to the receiver Smart ButtonTM GB-318 user’s instruction to set up the unit.2a. PROGRAM TRANSMITTER TO RECEIVER GB-318Garage DoorTransmitter(Battery inside)3 Volt lithium battery (CR 2032) (included).It is time to change the battery when the red LED on the transmitter doesnot turn on when either button is pressed.4. BATTERYIf, within one year from date of purchase, this product should become defective(except battery), due to faulty workmanship or materials, it will be repaired orreplaced, without charge. Proof of purchase and a Return Authorization are required.7. WARRANTY5. FCCThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interferencereceived, including interference that may cause undesired operation.WARNING:Changes or modifications to this unit not expressly approved by the party responsible for compliance couldvoid the user’s authority to operate the equipment.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts delicence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire debrouillage, et (2) L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d’en compromettre le fonctionmement.8. CUSTOMER SERVICECUSTOMER SERVICE17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3Email:support@skylinkhome.comhttp://www.skylinkhome.comP/N : 101Z993Patent Pending©2010 SKYLINK GROUPSmart ButtonTM GB-318 can learn up to 10 remote controls.To program the transmitter to the receiver, follow the instructions below:1. Press the learn button on the side of the Smart ButtonTM GB-318.2. Once the learn button is pressed, the LED willflash quickly. Release the learn button.3. Within 30 seconds, press any one of the 3 buttonson the transmitter that you want to program to thereceiver.4. Once the remote control is programmed, the LEDwill flash slowly, in the same way as it flashesin standby mode.5. You may now operate the garage door openerwith this new remote control.6. To program this transmitter to control anotherreceiver, repeat process (1) to (4) to programanother button on the remote control.You need to do the programming in order to add the transmitter to aSkylink® Garage Door Opener.Skylink® Garage Door Opener can learn up to 16 remote controls.To program the transmitter to the Garage Door Receiver, follow theinstructions below:1. Press the LEARN/SET button once on the garage door opener.2. Once the LEARN/SET buttton is pressed, the LEARN LED will flash.You may release the LEARN/SET button.3. Within 30 seconds, press any one of the 3 buttons on the transmitterthat you want to program to the receiver.4. Once the transmitter is programmed, the LEARN LED will turn off.5. You may now operate the garage door opener with this new transmitter.6. To program a transmitter to control another garage door opener,repeat process (1) to (4) to program another button on the transmitter.2b. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR OPENER - EQ SERIESTo program the transmitter to the Skylink® IQ series Garage Door Opener,please follow the user’s instruction from the Garage Door Opener. 3. TROUBLE SHOOTINGQ: What can I do if the door opener does not react after I press the button onthe transmitter ?A: - Ensure when the button on the transmitter is pressed, the red light on thetransmitter comes on. Otherwise, check if the battery is inserted properly.- Make sure the correct button on the transmitter is pressed.- Ensure the wires that were previously connected to the wall mounteddoor control are not loose.- Ensure the transmitter has been programmed to the receiver. Referto section 2 for how to program a transmitter to the receiver.2d. PROGRAM A TRANSMITTER TO THE SKYLINK® GARAGE DOOR OPENER - IQ SERIESLearn ButtonThere are three buttons on transmitter MK-318, each button can beprogramed to control Skylink garage door receiver Smart ButtonTM GB-318or GB-318-3 or Skylink garage door opener directly.Follow one or more instructions below in Section 2 to program transmitterMK-318 to the receiver or receivers you want to control.LearnButtonSmart ButtonTMGB-318LEDAntenna2c. PROGRAM A TRANSMITTER TO RECEIVER GB-318-3To program the transmitter to a Skylink Garage DoorReceiver Smart ButtonTM GB-318-3 (3 doors) , pleasefollow the user’s instruction for the model GB-318-3.If you would like to- find out the up-to-date specifications- know more about features and applications- download documents, i.e. user’s instructions- order Skylink productsor if you have difficulty getting products to work, please:1. visit our FAQ section at www.skylinkhome.com, or2. email us at support@skylinkhome.com, or3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.Fax (800) 286-13206. IC

Navigation menu