Capital Prospect PA-318 Plug-in Remote Control User Manual mPA 318

Download:
Mirror Download [FCC.gov]
Document ID	2889270
Application ID	EhGzLCFKLD2O28VRkL3VJA==
Document Description	15_PA-318 UserMan
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	307.09kB (3838654 bits)
Date Submitted	2016-01-29 00:00:00
Date Available	2016-01-29 00:00:00
Creation Date	2010-07-17 23:29:14
Producing Software	Corel PDF Engine Version 9.337
Document Lastmod	2016-01-21 09:39:10
Document Title	mPA-318.cdr
Document Creator	CorelDRAW Version 9.337
Document Author:	Joe

PFCC ID:KUTPA-318
Model PA-318
3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS (CONT)
1. INTRODUCTION
Thank you for your purchase of a SkylinkHomeTM lighting receiver,
Plug-In Remote Control, Model PA-318. This receiver module
allows you to wirelessly turn on and off different lighting fixtures with the
SkylinkHomeTM lighting transmitters.
The Plug-In Remote Control PA-318 can communicate with up
to 16 transmitters, so user has the option to add more transmitters to the
system, such as more remote controls, or motion sensors etc.
All wireless signal communications within the SkylinkHomeTM lighting
system are based on rolling code technology to ensure highest security
is used.
The following items are included in this package:
- Plug-In Remote Control
- Antenna
- User's Instructions
Antenna
Operating Mode
LED Indication
On / Off
Flashing
Timer
Steadily On
5. If you are programming a transmitter with On / Off
operation, follow steps A) to C). Otherwise, go to
step 6)
A. Press the PROG button on the back of the
TC transmitter with a sharp object.
B. Press the button on the TC transmitter that
you would like to program into the module.
C. Once the transmitter is programmed, the
red LED on the module flashes quickly then
stops flashing, indicating you have successfully
programmed the transmitter to the module.
D. You may operate the light with the programmed
transmitter.
6. If you are programming a transmitter with Timer
operation, continue to hold the “SET” button for
another 6 seconds, until the LED is on steadily,
then you may now follow steps 5A) to 5C) to
complete the programming sequence.
“PROG” switch
Press the
desired
button
Note: To program other transmitters/sensors (besides TC transmitter),
please refer to the instructions of thetransmitters/sensors.
2. SETUP
Insert the antenna to the Plug-In Remote Control
as shown. Place the antenna in
the upright position to have the best reception.
Simply plug the Plug-In Remote Control
to an electrical outlet, then plug in a light or home
appliance that you would like to operate to the
socket on the Plug-In Remote Control.
Note: You must complete the programming sequence within the
15-second interval, otherwise, the module will quit from programming
mode and you need to start again from step 1 if the red LED is off.
You may follow the same instructions to program additional transmitters
or sensors to operate the receiver module.
Note: Lighting Load
4. SET TIMER DURATION
The Plug-In Remote Control is designed
to operate maximum load of 1500W at 120VAC.
Do not connect loading that exceeds this maximum rating.
As mentioned, the timer can be set to the following durations, 1 minute,
5 minutes, 10 minutes, 30 minutes, and 60 minutes.
Follow the programming instructions below to get started.
There is only one timer setting, so all transmitters that are programmed
in timer mode will have the same timer duration. To set the timer duration,
follow the instructions below:
3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS
In order to operate the Plug-In Remote Control remotely with a
transmitter or sensor, it must be programmed to the Plug-In
Remote Control. Each module can be operated by up to 16 different
transmitters (or 16 different command signals).
There are 2 operating modes with the Plug-In Remote Control:
1. Plug in the module to an AC socket so it is powered on properly.
2. Turn off the connected load by a programmed transmitter. The load
must be off in order to set the timer duration.
3. Press and hold the SET button for 3 seconds, the red LED flashes
once. The number of flash indicates the timer duration:
Number of Flashes
Timer Duration
1) On / Off Mode When a valid signal is received, it will toggle the load,
i.e. turning off or on the light
2) Timer Mode When a valid signal is received, the load will be on for
a specific period of time, from 1 minute, 5 minutes, 15 minutes,
30 minutes, and 60 minutes
1 min.
To program a transmitter / Sensor into the Plug-In
Remote Control, follow the instructions below.
LED Flashing: On/Off Mode
LED Steadily ON: Timer Mode
5 min.
15 min.
30 min.
60 min.
1. Plug in a load to the Plug-In
Remote Control
2. Plug in the module to an AC electrical
outlet, the red LED flashes once quickly.
The connected load (i.e. light) will be on
automatically.
3. Press and hold the “SET” button for about
3 seconds, unit the red LED flashes once.
You may now release the “SET” button.
4. The red LED will continue to flash for
about 15 seconds. You can now decide
the operating mode of the transmitter
that you plan to program.
Red LED
4. Continue to hold the SET button until it reaches the desired setting. The
status will change every 6 seconds, i.e. hold onto the SET button for
another 6 seconds, you will see the number of flashes changes from 1
to 2, 2 to 3 etc.
Note: Once the number of flash reaches 5, it will stay at this setting. If
you would like to go back to other settings, such as 1 flash, release the
button and repeat from step 1 to start over.
3 Light On
Once a transmitter (button) is programmed in timer mode, activating this
programmed transmitter (button) will turn on the light for the specified
timer duration.
During a timer count down, if the module receives another signal for timer
operation, the timer will start again and overrides the previous timer,
therefore, extending the on period by another timer interval.
5. ON / OFF OPERATION
The PA-318 Plug-In Remote Control allows on / off operation
if on / off operation is selected. When the programmed button is activate,
it will transmit a signal to toggle its current status. For example, if a signal
is received when the light is off, that signal will turn on the light.
Note:
When used with Compact Fluorescent Light, if there is flickering when you
switch off the light, it is recommended you replace a different Compact
Fluorescent Light with higher quality.
6. ZONE OPERATION (AVAILABLE WITH 10-BUTTON /
14-BUTTON DELUXE TRANSMITTER ONLY)
A Zone Command allows you to operate multiple lights at the same time
in the same zone. For instance, you may assign zone 1 to 3 different
lighting fixtures in the family room (each light has its own receiver module).
To set this up, refer to the Deluxe Transmitter user’s instructions.
10. FCC
The Remote Control is approved by the FCC and it complies with Part 15 of the
FCC Rules. Its operation is subject to the following two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
of compliance could void the user’s authority to operate the equipment.
11. CUSTOMER SERVICE
If you would like to order Skylink’s products or have difficulty getting them to work
or download latest information and user manual, please :
1. visit our FAQ section at www.skylinkhome.com, or
2. email us at support@skylinkhome.com, or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
12. ACCESSORIES
To activate the zone command, simply press “Zone On” or “Zone Off”,
then the zone number, i.e. [Zone On] + [1] means Zone 1 On.
Programming Zone Command
Enter [Zone On] + [Zone Number] during step 5B of the programming
sequence (ensure on / off operating mode is selected), the Zone
Command signal would be programmed. Repeat this step for all the
receiver modules in the same zone.
7. TIMER OPERATING MODE
If a transmitter or a sensor is programmed to the Plug-In Remote Control
under the timer mode, when that transmitter is activated, the
light connected will be on for the predetermined timer interval. After the
timer interval, the light will be off.
8. ERASING TRANSMITTERS FROM THE MODULE
You may erase a transmitter or sensor from the
module, but you cannot erase a specific device, you
must erase all the wireless devices, then program
the ones you want to keep. Follow the instructions
below to erase programmed transmitters / sensors.
1. Power off the Plug-In Remote Control
by removing it from the AC socket.
2. Press and hold the SET button, while holding onto
the SET button, plug in the module to an AC socket.
3. The red LED will be on first, then flashes rapidly
for 1 second.
4. You may release the SET button, the
Press and hold the SET
button while plugging
light attached to the module is now on,
it in to an AC socket
indicating you have successfully erased
all the devices from the lighting receiver.
5. You may remove the module from the
socket to power it off completely, or
refer to the programming instructions
to program the transmitters you would
like to keep.
9. TECHNICAL SPECIFICATIONS
Input Voltage: 120V AC, 60Hz
Standby Current: 5mA
Maximum Rating: 13 Amps
Maximum Load: 1500W at 120AVC
Operating Frequency: 318MHz
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101Z700
Patent Pending
©2010 SKYLINK GROUP
The SkylinkHomeTM Lighting System consists of many other devices from
multiple button transmitters, Motion Sensor, various receivers such as
Wall Switch Receiver, Plug-in Receiver with Repeater, Outdoor Receiver,
Dimmer Module etc. Please visit Skylink website at www.skylinkhome.com
for more information.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
XMP Toolkit                     : 3.1-701
Create Date                     : 2010:07:17 23:29:14Z
Creator Tool                    : CorelDRAW Version 9.337
Modify Date                     : 2016:01:21 09:39:10+08:00
Metadata Date                   : 2016:01:21 09:39:10+08:00
Format                          : application/pdf
Creator                         : Joe
Title                           : mPA-318.cdr
Producer                        : Corel PDF Engine Version 9.337
Document ID                     : uuid:b59ebc8b-7f32-485b-8036-423c3c12f63d
Instance ID                     : uuid:d7b9181c-b819-44e9-adcb-5375efa31bf8
Page Count                      : 2
Author                          : Joe

EXIF Metadata provided by EXIF.tools