Capital Prospect PA-318 Plug-in Remote Control User Manual mPA 318
Capital Prospect Ltd Plug-in Remote Control mPA 318
Contents
- 1. User manual
- 2. 15_PA-318 UserMan
15_PA-318 UserMan
PFCC ID:KUTPA-318 Model PA-318 3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS (CONT) 1. INTRODUCTION Thank you for your purchase of a SkylinkHomeTM lighting receiver, Plug-In Remote Control, Model PA-318. This receiver module allows you to wirelessly turn on and off different lighting fixtures with the SkylinkHomeTM lighting transmitters. The Plug-In Remote Control PA-318 can communicate with up to 16 transmitters, so user has the option to add more transmitters to the system, such as more remote controls, or motion sensors etc. All wireless signal communications within the SkylinkHomeTM lighting system are based on rolling code technology to ensure highest security is used. The following items are included in this package: - Plug-In Remote Control - Antenna - User's Instructions Antenna Operating Mode LED Indication On / Off Flashing Timer Steadily On 5. If you are programming a transmitter with On / Off operation, follow steps A) to C). Otherwise, go to step 6) A. Press the PROG button on the back of the TC transmitter with a sharp object. B. Press the button on the TC transmitter that you would like to program into the module. C. Once the transmitter is programmed, the red LED on the module flashes quickly then stops flashing, indicating you have successfully programmed the transmitter to the module. D. You may operate the light with the programmed transmitter. 6. If you are programming a transmitter with Timer operation, continue to hold the “SET” button for another 6 seconds, until the LED is on steadily, then you may now follow steps 5A) to 5C) to complete the programming sequence. “PROG” switch Press the desired button Note: To program other transmitters/sensors (besides TC transmitter), please refer to the instructions of thetransmitters/sensors. 2. SETUP Insert the antenna to the Plug-In Remote Control as shown. Place the antenna in the upright position to have the best reception. Simply plug the Plug-In Remote Control to an electrical outlet, then plug in a light or home appliance that you would like to operate to the socket on the Plug-In Remote Control. Note: You must complete the programming sequence within the 15-second interval, otherwise, the module will quit from programming mode and you need to start again from step 1 if the red LED is off. You may follow the same instructions to program additional transmitters or sensors to operate the receiver module. Note: Lighting Load 4. SET TIMER DURATION The Plug-In Remote Control is designed to operate maximum load of 1500W at 120VAC. Do not connect loading that exceeds this maximum rating. As mentioned, the timer can be set to the following durations, 1 minute, 5 minutes, 10 minutes, 30 minutes, and 60 minutes. Follow the programming instructions below to get started. There is only one timer setting, so all transmitters that are programmed in timer mode will have the same timer duration. To set the timer duration, follow the instructions below: 3. PROGRAMMING TRANSMITTERS (TC SERIES) / SENSORS In order to operate the Plug-In Remote Control remotely with a transmitter or sensor, it must be programmed to the Plug-In Remote Control. Each module can be operated by up to 16 different transmitters (or 16 different command signals). There are 2 operating modes with the Plug-In Remote Control: 1. Plug in the module to an AC socket so it is powered on properly. 2. Turn off the connected load by a programmed transmitter. The load must be off in order to set the timer duration. 3. Press and hold the SET button for 3 seconds, the red LED flashes once. The number of flash indicates the timer duration: Number of Flashes Timer Duration 1) On / Off Mode When a valid signal is received, it will toggle the load, i.e. turning off or on the light 2) Timer Mode When a valid signal is received, the load will be on for a specific period of time, from 1 minute, 5 minutes, 15 minutes, 30 minutes, and 60 minutes 1 min. To program a transmitter / Sensor into the Plug-In Remote Control, follow the instructions below. LED Flashing: On/Off Mode LED Steadily ON: Timer Mode 5 min. 15 min. 30 min. 60 min. 1. Plug in a load to the Plug-In Remote Control 2. Plug in the module to an AC electrical outlet, the red LED flashes once quickly. The connected load (i.e. light) will be on automatically. 3. Press and hold the “SET” button for about 3 seconds, unit the red LED flashes once. You may now release the “SET” button. 4. The red LED will continue to flash for about 15 seconds. You can now decide the operating mode of the transmitter that you plan to program. Red LED 4. Continue to hold the SET button until it reaches the desired setting. The status will change every 6 seconds, i.e. hold onto the SET button for another 6 seconds, you will see the number of flashes changes from 1 to 2, 2 to 3 etc. Note: Once the number of flash reaches 5, it will stay at this setting. If you would like to go back to other settings, such as 1 flash, release the button and repeat from step 1 to start over. 3 Light On Once a transmitter (button) is programmed in timer mode, activating this programmed transmitter (button) will turn on the light for the specified timer duration. During a timer count down, if the module receives another signal for timer operation, the timer will start again and overrides the previous timer, therefore, extending the on period by another timer interval. 5. ON / OFF OPERATION The PA-318 Plug-In Remote Control allows on / off operation if on / off operation is selected. When the programmed button is activate, it will transmit a signal to toggle its current status. For example, if a signal is received when the light is off, that signal will turn on the light. Note: When used with Compact Fluorescent Light, if there is flickering when you switch off the light, it is recommended you replace a different Compact Fluorescent Light with higher quality. 6. ZONE OPERATION (AVAILABLE WITH 10-BUTTON / 14-BUTTON DELUXE TRANSMITTER ONLY) A Zone Command allows you to operate multiple lights at the same time in the same zone. For instance, you may assign zone 1 to 3 different lighting fixtures in the family room (each light has its own receiver module). To set this up, refer to the Deluxe Transmitter user’s instructions. 10. FCC The Remote Control is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions : 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible of compliance could void the user’s authority to operate the equipment. 11. CUSTOMER SERVICE If you would like to order Skylink’s products or have difficulty getting them to work or download latest information and user manual, please : 1. visit our FAQ section at www.skylinkhome.com, or 2. email us at support@skylinkhome.com, or 3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320 12. ACCESSORIES To activate the zone command, simply press “Zone On” or “Zone Off”, then the zone number, i.e. [Zone On] + [1] means Zone 1 On. Programming Zone Command Enter [Zone On] + [Zone Number] during step 5B of the programming sequence (ensure on / off operating mode is selected), the Zone Command signal would be programmed. Repeat this step for all the receiver modules in the same zone. 7. TIMER OPERATING MODE If a transmitter or a sensor is programmed to the Plug-In Remote Control under the timer mode, when that transmitter is activated, the light connected will be on for the predetermined timer interval. After the timer interval, the light will be off. 8. ERASING TRANSMITTERS FROM THE MODULE You may erase a transmitter or sensor from the module, but you cannot erase a specific device, you must erase all the wireless devices, then program the ones you want to keep. Follow the instructions below to erase programmed transmitters / sensors. 1. Power off the Plug-In Remote Control by removing it from the AC socket. 2. Press and hold the SET button, while holding onto the SET button, plug in the module to an AC socket. 3. The red LED will be on first, then flashes rapidly for 1 second. 4. You may release the SET button, the Press and hold the SET button while plugging light attached to the module is now on, it in to an AC socket indicating you have successfully erased all the devices from the lighting receiver. 5. You may remove the module from the socket to power it off completely, or refer to the programming instructions to program the transmitters you would like to keep. 9. TECHNICAL SPECIFICATIONS Input Voltage: 120V AC, 60Hz Standby Current: 5mA Maximum Rating: 13 Amps Maximum Load: 1500W at 120AVC Operating Frequency: 318MHz CUSTOMER SERVICE 17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3 Email:support@skylinkhome.com http://www.skylinkhome.com P/N. 101Z700 Patent Pending ©2010 SKYLINK GROUP The SkylinkHomeTM Lighting System consists of many other devices from multiple button transmitters, Motion Sensor, various receivers such as Wall Switch Receiver, Plug-in Receiver with Repeater, Outdoor Receiver, Dimmer Module etc. Please visit Skylink website at www.skylinkhome.com for more information.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No XMP Toolkit : 3.1-701 Create Date : 2010:07:17 23:29:14Z Creator Tool : CorelDRAW Version 9.337 Modify Date : 2016:01:21 09:39:10+08:00 Metadata Date : 2016:01:21 09:39:10+08:00 Format : application/pdf Creator : Joe Title : mPA-318.cdr Producer : Corel PDF Engine Version 9.337 Document ID : uuid:b59ebc8b-7f32-485b-8036-423c3c12f63d Instance ID : uuid:d7b9181c-b819-44e9-adcb-5375efa31bf8 Page Count : 2 Author : JoeEXIF Metadata provided by EXIF.tools