Capital Prospect PS434A Motion Alert User Manual MPS434A1
Capital Prospect Ltd Motion Alert MPS434A1
User Manual
1. Power up the Motion Sensor and wait 45 seconds to warm up.
2. Enter the current MPIN (Master Identification Number) in the
Security Control Panel (SC-001)
3. Press [B].
4. Press the number key to identify which zone to add the Motion
Sensor to [1, 2, 3, 4]. We recommend you program the motion
sensor to zone 2. The zone light will flash for eight seconds.
5. While the zone light is flashing, press [*].
6. While the zone light is flashing, walk in front of the Motion Sensor
in order to activate it. You will hear a long beep if the motion
sensor is “learned” to the control panel. The zone light will stop
flashing and the remote sensor will now communicate to that zone.
2. SET UP THE MOTION SENSOR
1. INTRODUCTION
Motion Alert Model PS-434A
The Motion Alert is designed to monitor movement around your house.
The motion sensor can be placed either indoor or outdoor. Once motion
is detected, the receiver will beep & flash.
In this package, you should find an
Indoor/Outdoor Motion Sensor,
ball-head joint, screws and a clip.
Please follow the instructions below to setup your motion sensor and
the receiver.
2 pcs 3 x 18 screws
(Included) Indoor/Outdoor
Motion Sensor
Ball-head joint
The sensitivity of the motion sensor is adjustable. Change the setting by
placing the connector on either the ”High” or “Low” position. When the
sensitivity is set to “Low”, more movement is required to trigger the
sensor. It is recommended to set the sensitivity to “Low” and perform a
“Walk Test” (Described in Section 3 - “Walk Test”). If the walk test result
is satisfied, the sensitivity does not
require to be adjusted further. If the
walk test result shows the sensitivity
is too low, then you can change the
sensitivity setting to “High”. Please
perform the walk test after changing
the sensitivity setting.
2. SENSOR SENSITIVITY
Sensitivity Connectors on Motion Sensor
A ball-head joint is necessary to mount the sensor at a desire location.
A height of 5-6 ft is recommended, depending on your application. Once
a location is selected, mount the ball-head joint to this location by screws
provided, (see diagram 1). Once the ball-head joint is mounted to the
wall, slide the back of the sensor into the ball-head joint (see diagram 2).
The mounting angle can be adjusted. Please refer to Section 3 “Walk
Test” to determine the best mounting angle.
MOUNTING
After mounting the sensor at the desired location, it is
important to perform a walk test in order to determine
if the sensor is detecting the things you want to detect.
In order to control how far the sensor can “see”, this can be done by
adjusting the angle of the sensor. To reduce the detection range, simply
move the sensor downward. To increase the range, move the sensor
up to around 12 degrees. This will give the maximum range. However,
this may not be desired if the sensor is placed outdoors, since a false
trigger may occur if the sensor is set to detect motion in a distance.
4. WALK TEST
1. Program the Motion Sensor to the Security Control Panel (SC-001)
1. Power up the Motion Sensor and wait 45 seconds to warm up.
2. With only the “ON” light lit on the Audio Alarm, press and hold the
learn button located on the bottom of the Audio Alarm.
3. While pressing down on the button, activate the Motion Sensor by
walking in the monitored area.
4. If a connection has been made, the Audio Alarm will stop beeping
and make a continuous tone until the black learn button on the
Audio Alarm is released.
5. Now test the sensor by walking in the monitored area. If the Audio
Alarm beeps, they are communicating.
2. Program the Motion Sensor to the Audio Alarm (AA-433)
1. Power up the Motion Sensor and wait 45 seconds to warm up.
2. Press [L], [5] when in clock mode, the display will show “L5 Id
code”.
3. Activate the Motion Sensor within 5 seconds, the display will
return to clock model once the Motion Sensor has been learned.
4. If the Motion Sensor detects any movement, it will trigger the
Emergency Dialer and start dialing the preset phone numbers
(refer to AD-433S, AD-1010, ED-1010 User’s Instruction).
3. Program the Motion Sensor to the Emergency Dialer (AD-433S,
AD-1010, ED-1010)
3. INSTALLING THE MOTION SENSOR
You should walk in the area that you would like the sensor to monitor.
The receiver will beep if the sensor detects your movement. If the
receiver does not respond, adjust the mounting angle accordingly.
Perform the walk test again after 30 seconds. Repeat this procedure
until your motion is detected. There should be no movement in the
detected area during the 30 seconds.
Perform walk test in the undesired area to ensure movement cannot be
detected.
Tips: The sensor should not face
towards direct sunlight, placing
near heat or cold producing devices
(i.e. A/C or furnance vents, fans,
ovens, heaters etc.) that may
cause false triggers.
12º
4. FCC
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
5. WARRANTY
6. CUSTOMER SERVICE
CUSTOMER SERVICE
2213 Dunwin Drive, Mississauga, Ontario, L5L 1X1, CANADA
SKYLINK TECHNOLOGIES-USA
1100 East Valencia Drive, Fullerton, CA 92831 USA
TEL (714)224-4321
Email:support@skylinkhome.com (Reply within 24 hrs)
http://www.skylinkhome.com
P/N. 101A206-002 Rev.2
©2003 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com, or
2. email us at support@skylinkhome.com (reply within 24 hrs), or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax +800 286-1320
Diagram 1 Diagram 2
3. INSTALLING THE MOTION SENSOR (CONT)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.