Cardo Systems ER04 Scala-rider Q2 User Manual QGQ2 LONG 008 indd
Cardo Systems, Inc. Scala-rider Q2 QGQ2 LONG 008 indd
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 887655 |
| Application ID | rQDdCDCMfLHpqtouAvZW2g== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 279.41kB (3492648 bits) |
| Date Submitted | 2008-01-10 00:00:00 |
| Date Available | 2008-01-10 00:00:00 |
| Creation Date | 2007-10-16 14:21:58 |
| Producing Software | Adobe PDF Library 7.0 |
| Document Lastmod | 2007-10-16 14:23:14 |
| Document Title | QGQ2_LONG_008.indd |
| Document Creator | Adobe InDesign CS2 (4.0) |
CARDO SYSTEMS, INC. User Guide Gebrauchsanleitung Guide d’Utilisation Guida di Avvio Guia de Usario | INTRODUCTION | CONTENTS OF RETAIL BOX | Cardo Rider Q2™ INTRODUCTION CONTENTS OF RETAIL BOX Congratulations, and thank you for having chosen the Cardo Rider Q2 Bluetooth® Headset for bikers. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth® functionality of your cellular phone and/or GPS device before using the Cardo Rider Q2. Volume Up Headset Charging Jack The retail box of the Cardo Rider Q2 contains one headset unit. When paired with another Cardo Rider Q2, the headsets can be used as an Intercom at a range of up to 600 ft (200m). Volume Down The Cardo Rider Q2 offers the following uses: 1. Bluetooth headset for mobile phone communication, supporting headset* and Handsfree* profiles (10m range) 2. Bike-to-Bike Intercom Communication with another Q2 unit (up to 600 ft. / 200m range) in Full Duplex** mode [purchased separately] 3. Turn-by-Turn GPS Navigation instructions and Streaming Audio from compatible Bluetooth® devices 4. FM Radio – built in FM radio receiver with six preset stations CTRL – Control Button • Power On, Power Off • Answer/End MC – Multi-Connection • Radio On/Off/change stations • Initiate/Terminate Buddy Intercom call with Primary or Secondary Buddy Helmet Clamp The Cardo Rider Q2 can establish an audio connection with one Bluetooth® device at a time. Please read the section “Using the Headset” to see how you can switch the audio connection between the paired devices. Right Speaker (long cord) Microphone Tab Sliding Plate Left Speaker (short cord) ____________________ NOTE: The use of two speakers may be illegal in certain jurisdictions. Please check the local regulations and act accordingly. * Mobile phones that do not support the Bluetooth® Handsfree profile may prevent you from using the Redial and Call Reject features ** Full duplex calls allow you to speak and hear the other party speak simultaneously CONTENTS OF RETAIL BOX | BEFORE USING | Cardo Rider Q2™ | Full Duplex Intercom Connection Allen Wrench English SET UP AND CONFIGURATION Wall Charger Embedded FM Radio 200 meters (600 ft.) Velcro Pads Extension Pad Cardo Rider Q2 or scala-rider Family Headset User Guide, including Warranty and Registration form Mobile Phone GPS IMPORTANT: The Cardo Rider Q2 is a water-resistant device, designed for use under moderate rain or snow conditions. However, the headset is not waterproof and should not be used under severe weather conditions. The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device. STEP 1 SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING BEFORE USING (CHARGING THE HEADSET) The Cardo Rider Q2 can be paired with up to two other headsets for Intercom communication, referred to in this guide as: Primary Buddy and Secondary Buddy. Pairing is a one time process. Once the headsets are paired during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. Make sure that the headset is fully charged for at least five hours before initial use. 1. Connect the wall charger to the headset’s Charging Jack (located between the two Volume Buttons). 2. While charging, the Red Light turns on (it may take up to 15 seconds until the Red Light turns on). When charging is complete, the Red Light will turn off. NOTE: The Cardo Rider Q2 allows you to speak via Intercom to one Buddy headset at a time. | SETUP AND CONFIGURATION | Cardo Rider Q2™ PRIMARY BUDDY PAIRING (requires two Cardo Rider Q2 headsets) A. Both Rider and Passenger are using Cardo Rider Q2 headsets. To Pair the two headsets, follow the Steps listed in the section above titled PRIMARY BUDDY PAIRING. B. The Rider is using a Cardo Rider Q2 and the Passenger is using a scala-rider headset (i.e. a scala-rider, a scala-rider FM or a scalarider TeamSet Driver unit headset). To Pair the two headsets: 1. Starting with the scala-rider headset turned OFF, press and hold the CTRL button until the Red/Blue lights begin rapidly alternating. 2. Starting with the Cardo Rider Q2 turned ON, simultaneously press and hold the CTRL Button and MC Button for six seconds until the Red light begins flashing rapidly, indicating it is in Intercom Pairing mode. 3. Within a few seconds, the Cardo Rider Q2 will show a solid Red light for two seconds, and then begin flashing slowly in Blue. NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. NOTE: When using a scala-rider headset as a Passenger headset, Voice Connect Intercom can be initiated only by the Cardo Rider Q2 headset. Manual Connect Intercom can be initiated from either headset. 1. If either headset is turned OFF, turn it ON by pressing and holding the CTRL Button until the Blue Light flashes three times. 2. Make sure that both headsets are now flashing slowly in Blue. 3. Pick up one headset and simultaneously press and hold the CTRL Button and MC Button for at least six seconds until the Red Light begins flashing rapidly, indicating it is in Intercom Pairing mode. 4. Repeat Step 3 again for the second Cardo Rider Q2 headset. Both headsets should now be flashing rapidly in Red. 5. Within a few seconds, both headsets will show a solid Red light for two seconds, and then begin flashing slowly in Blue. SECONDARY BUDDY PAIRING (requires three Cardo Rider Q2 headsets) Once you have paired the Main Cardo Rider Q2 to the Primary Buddy headset, repeat the procedure above to pair the Main Cardo Rider Q2 to the Secondary Buddy headset. NOTE: The Main Cardo Rider Q2 is able to communicate with either the Primary Buddy or the Secondary Buddy. The Primary Buddy and Secondary Buddy are not able to communicate directly via Intercom. RESET INTERCOM PAIRING You can delete all of the headset’s Intercom pairings at any time. NOTE: If the Pairing process is not completed within one minute the headset will return to Standby mode. 1. Place the Cardo Rider Q2 into Intercom Pairing mode following the instructions in the PRIMARY BUDDY PAIRING section above. 2. Once the Red Light begins flashing rapidly, press and hold Volume up for three seconds. STEP 2 (Optional) 3. The Red and Blue Lights will flash five times, confirming that the Reset Pairing was successful. SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING There are two ways that the Cardo Rider Q2 can be used for Rider-toPassenger communication. SETUP AND CONFIGURATION | Cardo Rider Q2™ | SET UP FOR MOBILE PHONE CALLS: PAIRING With some mobile phones, you may need to tap the CTRL button to connect the headset to the phone after pairing is complete. The Cardo Rider Q2 headset will automatically connect to the last phone connected to the headset. If you have a Bluetooth® enabled mobile phone and would like to make and receive phone calls using the Cardo Rider Q2, you must first pair your headset to the mobile phone. STEP 4 NOTE: If you have a compatible Bluetooth® GPS device you wish to use with the Cardo Rider Q2, please skip this step, and continue ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE. SET UP FOR BLUETOOTH GPS DEVICE: PAIRING If you have a Bluetooth® enabled GPS device and would like to transmit navigation instructions and sounds from the GPS device through the headset’s speakers, you must first pair your headset to the GPS device. Pairing is a one time process. Once the headset is paired to a specific mobile phone during this Setup Procedure, they will remain paired and automatically recognize each other whenever they are within range. If the connection between the phone and headset is lost, tap the CTRL button to reconnect the devices. NOTE: Not all Bluetooth® enabled GPS devices allow connections to Bluetooth® headsets like the Cardo Rider Q2. Please consult your GPS device’s User Manual for more information. TO PAIR THE CARDO RIDER Q2 TO A BLUETOOTH MOBILE PHONE TO PAIR THE CARDO RIDER Q2 TO A BLUETOOTH® GPS DEVICE: 1. Turn on your phone and make sure its Bluetooth® function is activated. 2. With the Cardo Rider Q2 headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 3. Search for Bluetooth® devices on your phone by following the phone’s instructions. Please consult your phone’s User Manual for more information. 4. After a few seconds the phone will list the Cardo Rider Q2 as a discovered device. Select it and follow your phone’s instructions to accept the pairing. 5. When prompted enter 0000 (four zeros) as your PIN or passkey. 6. Your phone will confirm that pairing has succeeded and the headset will begin flashing slowly in Blue. 1. Turn on your GPS device. 2. With the Cardo Rider Q2 headset turned ON, press and hold the CTRL Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. 3. Search for Bluetooth® headsets on your GPS device by following the device’s instructions. Please consult your GPS device’s User Manual for more information. 4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros). 5. Your GPS device will confirm that pairing has succeeded. The headset will begin flashing slowly in Blue. 6. If you wish to use a Bluetooth® mobile phone to make and receive calls through the headset, you must now pair your English NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. STEP 3 | SETUP AND CONFIGURATION | Cardo Rider Q2™ REMOVING: mobile phone to your GPS device by following your GPS and/or mobile phone’s instructions. NOTE: If the Pairing process is not completed within two minutes the headset will return to Standby mode. Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you remove the headset from the helmet when not in use. MOUNTING THE HEADSET ON THE HELMET The microphone/speaker clamp must be mounted onto the helmet. Once mounted, the headset unit can be attached or detached from the microphone/speaker clamp at any time. Press here to remove Allen Wrench Back Plate SPEAKERS AND MICROPHONE POSITIONING The microphone must be positioned vertically, not horizontally, in front of the center of the mouth, with the yellow sticker pointing towards the mouth. Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for left ear & long speaker cord for right ear), or use the supplied Velcro pads. Attaching the Clamp to the Helmet 1. Use the enclosed Allen Wrench to loosen the two screws on the Back Plate. 2. Slide the Back Plate between the internal padding and the external shell of the helmet. (If the external shell is too thick, use the supplied plastic Extension Pad by loosening the screws and fitting the Extension Pad between the Back Plate and the main body of the clamp.) 3. Adjust the clamp’s location so that the microphone is located in front of the center of your mouth, with the yellow sticker pointing towards your CORRECT INCORRECT mouth, and then tighten the screws. USING THE HEADSET GENERAL USAGE GENERAL FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Increase the volume Decrease the volume ATTACHING AND REMOVING THE HEADSET FROM THE HELMET CLAMP ATTACHING: REQUIRED ACTION: Press the CTRL Button steadily for at least three seconds Press the CTRL Button steadily for at least three seconds Short press the Volume Up Button Short press the Volume Down Button AGC (Automatic Gain Control): In addition to manual Volume Control, the Cardo Rider Q2 will automatically increase and reduce its volume according to ambient noise and driving speed. Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. SETUP AND CONFIGURATION | Cardo Rider Q2™ | AUDIO SOURCES AND PRIORITIES USING THE INTERCOM Receiving Intercom calls Making Intercom calls If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately. The different Audio Sources that are connected to the Cardo Rider Q2 are prioritized as follows: Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls , GPS audio and navigation instructions) 2. Primary Buddy Audio and Secondary Buddy Audio Lowest 3. FM Radio To start a Buddy Intercom call with the Primary Buddy while the headset is on Standby you can either: VOICE CONNECT: Start talking A Buddy Intercom call will be established and stay on until both sides are quiet for 30 seconds. or TROUBLESHOOTING THE INTERCOM: MC BUTTON CONNECT: First, make sure your microphone is located properly in front of the center of your mouth. Single tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, single tap the MC Button again. The Cardo Rider Q2 is designed for use in loud environments. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections. To start a Buddy Intercom call with the Secondary Buddy while the headset is on Standby: MC BUTTON CONNECT: MC Button Setting Voice Connect Intercom preference (Primary vs. Secondary Buddy) Double tap the MC Button A Buddy Intercom call will be established. To end the Buddy Intercom call, double tap the MC Button again. The headset’s Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone. You can define English A high priority Audio Source will always interrupt any lower priority Audio Source. i.e. Mobile phone call interrupts Intercom call Intercom call interrupts FM Radio NOTE: When using a scala-rider Headset as a Passenger headset, Voice Connect Intercom can be initiated only by the Cardo Rider Q2 headset. Manual Connect Intercom can be initiated from either headset. Failed Connection: On the Cardo Rider Q2, if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone/GPS/ Intercom call, you will hear a double beep indicating the Buddy is busy. Reconnecting the Intercom: If the Cardo Rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other, the Cardo Rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes. You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy). | SETUP AND CONFIGURATION | Cardo Rider Q2™ When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically. Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls. which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom. NOTE: The Primary Buddy has priority by default. To toggle the Voice Connect Intercom between Primary and Secondary Buddy: Press and hold the Volume Up Button for three seconds and you will hear a beep: • One beep – Voice Connect set to Primary Buddy • Two beeps – Voice Connect set to Secondary Buddy STATUS LIGHT STATES Enable/Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep. The default status is Voice Connect enabled. NOTE: The Enable/Disable Voice Connect feature affects both the Intercom and the mobile phone functionality. Reject a call Terminate a call Voice Dial Redial Headset is off Alternating Red/blue flashes Mobile phone/GPS Pairing mode Rapid Red flashes Intercom Pairing mode 1 blue flash every 3 seconds Standby – No call is in progress 2 blue flashes every 3 seconds Call being initiated or in progress / FM Radio ON MAKING AND RECEIVING MOBILE PHONE CALLS Answer a call None PHONE FUNCTIONS Short press the CTRL Button or speak loudly any word of your choice. Short press the MC Button or remain silent for 15 seconds. Short press the CTRL Button. 1 red flash every 3 seconds Battery is low 2 red flashes every 3 seconds Call being initiated or in progress / FM Radio ON and battery is low Solid red Headset is being charged WORKING WITH THE FM RADIO Your headset is equipped with a high-quality FM Radio receiver. This section explains how to enjoy the functions of the FM Radio. The Cardo Rider Q2 enables you to listen to FM Radio while you are not receiving audio from another audio source. During Standby, short press the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. Press and hold the Volume Down Button for three seconds. While listening to the radio, you do not have to worry about missing any calls, as the headset automatically mutes the FM Radio and switches to Bluetooth® headset operation when an incoming call is received, or when you decide to initiate a call. When the conversation is over, the headset automatically tunes back in to the FM Radio. Turning the FM Radio On NOTE: If your Bluetooth® mobile phone is paired to a Bluetooth® GPS device, not directly to the Cardo Rider Q2, some of the above Phone functions may not be compatible. While no call is on the headset (either mobile phone call or Intercom call), press and hold the MC Button on your headset for three seconds to turn SETUP AND CONFIGURATION | SUPPORT | NOTICES Cardo Rider Q2™ | Turning the FM Radio Off While the radio is turned on, press and hold the MC button for three seconds to turn the Radio off. Switching Preset FM Radio Station SUPPORT There are six pre-set Radio stations available on your Cardo Rider Q2. While the Radio is on, tap the MC Button to cycle between saved stations. For additional information please visit our website at www.cardosystems.com FAQ: www.cardosystems.com/faq or contact us at: support@cardosystems.com Searching for a New FM Radio Station While the Radio is on, press and hold the Volume Up or Volume Down Button for three seconds or until you hear the next station on your headset. Phone: Pressing Volume Up will search upwards (higher frequency). Pressing Volume Down will search downwards (lower frequency). Once a station is found, searching stops and you can hear the station. USA and Canada – + 1-800-488-0363 International – +4989 450 36819 To save this station, refer to the following section. To continue searching, press the Volume Up or Volume Down Button again for three seconds. NOTICES You may still continue to listen to the current unsaved station. Pressing the MC Button in this case will switch to the next saved station. FCC Notice Saving an FM Radio Station This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The FM Radio is equipped with a memory capacity of six stations. • Select the station you wish to replace by tapping the MC button until you find the station you want to replace. • Search for a new station as described above. • Tap the MC Button within 20 seconds of finding the station to save the current station. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. English If you don't save the station, the Radio will exit search mode without saving the current station. You can still continue to listen to the current unsaved station. Tapping the MC Button in this case will move to the next saved station. on the radio. The radio tunes in to the last radio station you were listening to. With some phones you should wait a few seconds after ending a call before turning on the Radio. | NOTICES | Cardo Rider Q2™ Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Use only approved batteries and chargers. This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Your Cardo Rider Q2™ headset is designed to operate at the maximum strength allowed by the FCC. This means that your headset can communicate only over a certain distance subject on the location of the cell phone, base unit and headset, your vehicle, the construction and layout of your home or office. Weather conditions can also affect performance. Specification 2.0 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth® -enabled products is not guaranteed. WAIVER AND GENERAL RELEASE By using the Cardo Rider Q2 you will waive substantial legal rights incc cluding the right to sue. Please read the following carefully before using the device. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue. Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-bike or any other vehicle or equipment, whether on land, water or air (jointly referred to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc., including its Officers, Directors, Affiliates, Parent Comppany, Representatives, Agents, Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the “Company” or “Cardo”) strongly advises you to take all necessary precautions and remain alert to the traffic, weather and road conditions if you choose to use the Cardo Rider Q2 headset, includiing all derivative models irrespective of its commercial name or branding (the “Device”), and stop your Vehicle on the roadside prior to initiating or receiving calls. Any publications, advertisements, announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic. CAUTION NEVER OPEN THE HEADSET AS THIS MAY CAUSE DAMAGE OR INJURY AND WILL VOID YOUR WARRANTY. NOTE: If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/ TV technician for help. By way of purchasing this Device and not returning it for a full refund (see bellow), you are irrevocably releasing, indemnifying from any liability, loss, claim and expense (including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or death as well as losses or damages in goods, to any Vehicles including your own, or to any property or asset that belong to you or to third parties, any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction. Cardo will not be responsible for any physical damages, irrespective of reasons, conditions or circumstances, including malfunctioning of the Device, and all risks associated with operating it rest solely and entirely with the user of this Device, irrespective of whether the Device is used by the original purchaser or any third party. European CE Notice The Cardo Rider Q2™ headset (the “Product”) is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordance with Annex II of the above directive. Declaration of Conformity (DOC) The Cardo Rider Q2™ headset is compliant with and adopts the Bluetooth® Cardo hereby notifies you that using this Device may also be in contravention 10 NOTICES | Cardo Rider Q2™ | LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL. 1. You, your heirs, legal representatives, successors or assigns, hereby volunttarily and forever release, discharge, indemnify and hold harmless Cardo from any and all litigation, claims, debts, demands, actions and liability which may arise, directly or indirectly, from using the Device for any distress, pain, sufferiing, discomfort, loss, injury, death, damages to or in respect to any person or property however caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you on some future date as a result of said use, to the fullest extent permitted by law. Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY. 2. You fully understand and assume the risks in using the Device, including risk of negligent acts or omissions by others. 3. You confirm that you are physically capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner. You confirm that you are at least eighteen (18) years of age and that you have been advised of the risks associated with the use of the Device. You further confirm that you will not consume any alcohol that may affect your alertness or any mind-altering substance, and will not carry, use or consume these substances before or during the use of the Device. RETURN FOR FULL REFUND 4. You fully acknowledge our warnings and understand that: (a) risks and danggers exist in using the Device while in traffic, incl. but not limited to injury or illness, strains, fractures, partial and/or total paralysis, death or other ailments that could cause serious disability; (c) these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device; (d) these risks and dangers may arise from foreseeable or unforeseeable causes. You hereby assume all risks and dangers and all responsibility for any losses and/or damages, whether caused in whole or in part by the negligence or other conduct of others, including the Company. IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDc DITIONS, YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND, PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFc FINED ABOVE. 5. You confirm that you have read this release of liability and fully understand its terms and that you have given up substantial rights by not returning the Device for a full refund (see refund option below). Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE, INCLUDING WITHOUT www.cardosystems.com 11 English to local, federal, state or national laws or regulations, and that any use of the Device is entirely at your sole risk and responsibility. | Cardo Rider Q2™ | NOTICES 12
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No XMP Toolkit : 3.1.1-111 Instance ID : uuid:9137b98b-7be2-11dc-a019-00145198b62a Document ID : adobe:docid:indd:25a16506-7cb0-11dc-840f-dec01fb77312 Rendition Class : proof:pdf Derived From Instance ID : fe7abdd4-7c95-11dc-840f-dec01fb77312 Derived From Document ID : adobe:docid:indd:eb7ad26e-7c09-11dc-840f-dec01fb77312 Derived From Manage To : http://10.10.10.13:3703/soap/Quick%20Guide%20Folder/documents/s-700%20folder/s-700LX%20SPANISH%20folder/QG700LXSP_001_LX%20Spanish%20.indd Derived From Manager : AdobeARM Create Date : 2007:10:16 14:21:58+02:00 Modify Date : 2007:10:16 14:23:14+02:00 Metadata Date : 2007:10:16 14:23:14+02:00 Creator Tool : Adobe InDesign CS2 (4.0) Thumbnail Format : JPEG Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Image : (Binary data 11077 bytes, use -b option to extract) Format : application/pdf Title : QGQ2_LONG_008.indd Producer : Adobe PDF Library 7.0 Trapped : False GTS PDFX Version : PDF/X-1:2001 GTS PDFX Conformance : PDF/X-1a:2001 Page Count : 12 Creator : Adobe InDesign CS2 (4.0)EXIF Metadata provided by EXIF.tools