Carewell Electric Technology AC6 REMOTE CONTROL User Manual AC26 61T 4S

Download:
Mirror Download [FCC.gov]
Document ID	3198373
Application ID	eDP972yqCbeb2JtmKNQQJA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.19kB (252424 bits)
Date Submitted	2016-11-17 00:00:00
Date Available	2016-11-17 00:00:00
Creation Date	2016-11-07 02:12:39
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	2016-11-07 02:12:39
Document Title	AC26+61T(4S)
Document Creator	CorelDRAW
Document Author:	Administrator

Remote controller
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off.
The light dimmer button will control the light brightness dimmer and off.
The blue indicator on the transmitter will light when one of the six buttons is pressed.
INSTRUCTION OF INSTALLATION AND OPERATION
1.SETTING THE CODES
This unit has 16 different code combinations. To set the codes, perform the following steps:
A. Setting the codes on the transmitter:
a. Remove battery cover. Press firmly on the arrow and slide battery cover off.
b. Slide code switches to your choice of up or down position. (Factory setting is all up. Do not use this position. Use a
Small screwdriver or ball point pen to slide firmly up or down (Figure 1)).
B. Setting the codes on the receiver:
The Learn Key must be pressed with in 30 seconds, after pressing the Power button.
If not, please press the Power button to restart.
Keep pressing the button learn key in excess of 3 second it becomes a LEARN status.
The receiver can remember the last codes status .The light flash two times.
2.INSTALLING RECEIVER IN CEILING FAN
A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by
removing fuse or switching off circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national
electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum
fan motor amps: 1.0, Maximum light watts: 60
incandescent or ballast.
Otherwise power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting
bracket.
c. Disconnect existing wiring between ceiling fan and
Supply in electrical junction box.
d. Make connections as follows, using the wire nuts
supplied: If other fans or supply wires are different
color, have this unit installed by qualified licensed
electrician.
e. Push all connected wires up into junction box.
f. Lay the brown antenna wire on top of the receiver,
and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power.
LEARN
LIGHT ON/OFF
CONNECT
Model AC26
3 2 1
6 5 4
9 8 7
TRANSMITTER
CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees,
For Mounting Controller, Model Ac26
CONNECT
TO
Green fan wire ....Bare supply wire
Black receiver wire(AC IN L) ....Black supply wire
White receiver wire(AC IN N) ....White supply wire
White receiver wire(TO LIGHT N) ....White fan wire
Red receiver wire(TO MOTOR) ....Red fan wire
Orange receiver wire(TO MOTOR) ....Orange fan wire
Gray receiver wire(TO MOTOR) ....Gray fan wire
Yellow receiver wire(TO MOTOR) ....Yellow fan wire
Blue receiver wire(FOR LIGHT L) ....Blue light wire
Use wire connecting nuts supplied with the fan
FROM POWER SOURCE
AC 110/120 VOLT 60Hz
3.5AMPS.
(FIG.3)
(FIG.2)
CANOPY
RECEIVER
RECEIVER
CANOPY
3. OPERATING TRANSMITTER:
A. Install 12 volt battery(not included). (To prevent damage to transmitter, remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. In order to prevent possible interference from or to
other remote units such as garage door openers, car alarm or security system. If you find that your fan and light kit go
on and off without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
key -for fan speed 1,2,3,4.
key-for fan speed 4,3,2,1.
REV key-for fan rev.
OFF key-for fan off.
LIGHT/DIMMER key-for light brightness and off.
LIGHT/DELAY key-for light after 3 minutes delay off.
The light function is controlled by pressing the LIGHT/DIMMER key down to increase or decrease light.
Tap
key quickly to turn light off or on.
Keep pressing the button in excess of 0.7 second and it becomes a dimmer, the light varies cyclically in 0.8 second.
The receiver can remember the last status of the light brightness when the light was switched, so that it can
resume to adjust the light brightness.
FCC Statement:
1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Industry Canada Notice This device complies with Industry Canada licence-exempt RSS standard(s). 1. Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device." 2.Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Avis d’Industrie Canada Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlements sur
l’interférence radio par un appareil numérique de classe B stipulées dans les Règlement sur l’interférence redio
d’industrie Canada.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may casue harmful interference to radio communications, However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- - - Reorient or relocate the receiving antenna.
- - - Increase the separation between the equipment and receiver.
- - - Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- - - Consult the dealer or an experienced radio/ TV technician for help.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
Optional Wall Mounting for Transmitter Holder
Place in accessible area of your home, and screw the
transmitter holder into wall using the two screws
provided, slide hand unit into holder.
OPERATION DISTANCE 20 FEET
4. TROUBLE SHOOTING GUIDE
1. Fails to operate
LR03 1.5V AAA
a. Power to receiver ?
LR03 1.5V AAA
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
f. Code set at exact same positions in both transmitter and receiver ?
2. Won ' t operate at distance
If transmitter operates fan/light kit when up close, but not at 20 feet away.
Try placing the brown antenna wire higher, up through ceiling/outside the junction box.
MODEL:
FAN61T-4S
TRANSMITTER
NOTICE !
Your ceiling fan and light kit assembly must meet the following requirements:
1. Do not use with solid state fans.
2. Electrical rating: 120v 60Hz 3.5A
MAX. Motor amps: 1.0
MAX. Light watts: 60-(incandescent or ballast)
WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER' S AUTHORITY TO OPERATE THE EQUIPMENT.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Create Date                     : D:20161107021239
Modify Date                     : D:20161107021239
Producer                        : Corel PDF Engine Version 3.0.0.667
Author                          : Administrator
Creator                         : CorelDRAW
Title                           : AC26+61T(4S)

EXIF Metadata provided by EXIF.tools