Carewell Electric Technology DC1 REMOTE CONTROL User Manual DC8 DC1 9KEY

Download:
Mirror Download [FCC.gov]
Document ID	2490032
Application ID	f59hmk+3TLJL+aebOI4CzQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.43kB (267825 bits)
Date Submitted	2015-01-04 00:00:00
Date Available	2015-01-05 00:00:00
Creation Date	2014-12-25 01:25:13
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	2014-12-25 01:25:13
Document Title	DC8+DC1(9KEY).cdr
Document Creator	CorelDRAW
Document Author:	Administrator

Remote controller
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are seven buttons (1, 2, 3, 4, 5, 6,OFF) to control fan speed and off.
The light dimmer button will control the light brightness dimmer and off.
The blue indicator on the transmitter will light when one of the nine buttons is pressed.
INSTRUCTION OF INSTALLATION AND OPERATION
1.SETTING THE CODES
Setting the codes on the transmitter:
a. Remove battery cover.
b. Factory setting is all on the “ON”position.If you want to change the codes setting,please use a
small screwdriver or a ball point pen to slide firmly to your choice of”ON”or”OFF”position.(Figure 1).
The Learn Key must be pressed within 30 seconds, after pressing the Power button.
If not, please press the Power button to restart.
Keep pressing the “LEARN”key in excess of 3 seconds it becomes a LEARN status.The receiver
can remember the last codes status.Then the light on the Fan will flash two times.
2.INSTALLING RECEIVER IN CEILING FAN
ACN
ACL
RECEIVER
ANT
INPUT
LIGHT
CODE
ON COMMON
LEARN
SWITCH
CODE
LIGHT
ON COMMON
LEARN
SWITCH
A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by
removing fuse or switching off circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national
electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum
fan motor watts: 40W, Maximum down light watts: 60W
led.
Otherwise power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting
bracket.
c. Disconnect existing wiring between ceiling fan and
Supply in electrical junction box.
d. Make connections as follows, using the wire nuts
supplied:
If other fans or supply wires are different color,
have this unit installed by qualified licensed electrician.
e. Push all connected wires up into junction box.
f. Lay the brown antenna wire on top of the receiver,
and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power.
DIM LEARN
OUTPUT
DIM LEARN
FAN
LIGHT
CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees,
For Mounting Controller, Model DC8
CONNECT
TO
Green fan wire ....Bare supply wire
Black receiver wire(AC IN L) .... Black supply wire
White receiver wire(AC IN N) ....White supply wire
Red receiver wire(TO MOTOR) .... Red fan wire
Grey receiver wire(TO MOTOR) .... Grey fan wire
Violet receiver wire(TO MOTOR) .... Violet fan wire
White receiver wire(FOR LIGHT ) ....White light wire
Blue receiver wire(FOR LIGHT) ....Blue light wire
Use wire connecting nuts supplied with the fan
FROM POWER SOURCE
AC 110~120 VOLT 60Hz
3.5AMPS.
(FIG.3)
WHITE
RED
RECEIVER
ANT
INPUT
(FIG.4)
OUTPUT
CANOPY
RECEIVER
ANTENNA PUT AT OUTSIDE
OF CANOPY BOX CAN GET
MORE OPERATION
DISTANCE
WIRE NUT
Use wire connecting nuts
supplied with the remote
CANOPY
PJES1412
3. OPERATING TRANSMITTER:
A. Install 3 volt battery(not included). (To prevent damage to transmitter, remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with rolling code combinations. In order to prevent possible interference from or to
other remote units such as garage door openers, car alarm or security system. If you find that your fan and light kit go
on and off without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
1-6 key -for fan speed control.
REV key-for fan REV.
OFF key-for fan off.
LIGHT key-for down light brightness .
The light function is controlled by pressing the LIGHT key down to increase or decrease light.
Tap
key quickly to turn light off or on.
Keep pressing the button in excess of 0.7 second and it becomes a dimmer, the light varies cyclically in 0.8 second.
The receiver can remember the last status of the light brightness when the light was switched, so that it can
resume to adjust the light brightness.
FCC Statement:
This device is in conformance with Part 15 of the FCC Rules and Regulations for Information Technology
Equipment. Operation of this product is subject to the following two conditions:
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Industry Canada Notice
This device complies with Industry Canada licence-exempt RSS standard(s).
1. Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device."
2.Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Avis d'Industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement. Cet appareil numérique ne dépasse pas les Rèlemenrs sur l'interférence radio par
un appareil numérique de classe B stipulées dans les Règlement ent sur l'interférence redio d'industrie Canada.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
OPERATION DISTANCE 20 FEET
SIZE: AAA 1.5V
CODE
LIGHT
LEARN
SWITCH
ON COMMON
SIZE: AAA 1.5V
DIM LEARN
SIZE: AAA 1.5V
SIZE: AAA 1.5V
MODEL:
DC1
Optional Wall Mounting for Transmitter Holder
Place in accessible area of your home, and screw the
transmitter holder into wall using the two screws
provided, slide hand unit into holder.
4. TROUBLE SHOOTING GUIDE
TRANSMITTER
1. Fails to operate
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
f. Code set at exact same positions in both transmitter ?
2. Won ' t operate at distance
If transmitter operates fan/light kit when up close, but not at 20 feet away.
Try placing the brown antenna wire higher, up through ceiling/outside the junction box.
NOTICE !
Your ceiling fan and light kit assembly must meet the following requirements:
1. Do not use with solid state fans.
2. Electrical rating: 120v 60Hz 3.5A
MAX. Motor watts: 40W
MAX. Light watts: 60W (led)
WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.
CAUTION: High Voltage-Disconnect power supply before servicing.
DANGER-To Reduce the RISK of Electric Shock-Do not connect to a circuit operating at more than 150 volts
to ground.
PJES1412

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2
Create Date                     : D:20141225012513
Modify Date                     : D:20141225012513
Producer                        : Corel PDF Engine Version 3.0.0.667
Author                          : Administrator
Creator                         : CorelDRAW
Title                           : DC8+DC1(9KEY).cdr

EXIF Metadata provided by EXIF.tools