Carrier CTSTO-00 Out Door Internet Camera User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3838498
Application ID	rykgTWIsurGWM2UplAttBQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.64kB (383029 bits)
Date Submitted	2018-05-03 00:00:00
Date Available	2018-05-03 00:00:00
Creation Date	2018-04-03 15:41:50
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2018-04-03 15:41:51
Document Title	Users Manual
Document Creator	Adobe InDesign CC 13.1 (Macintosh)

TROUBLESHOOTING
Connecting cables
Connect the power cable and network cable.
A The camera should already be set up in your
		Côr™ Smart Home account if you completed setup.
B If the camera was connected to a Wi-Fi®
		 network before, it will automatically connect to
		 the same network.
Q Côr Smart Home app reads “The camera is offline” or
“The device is not registered” when camera is added.
Make sure your router is connected to the Internet
and you have a good Wi-Fi® signal.
RESET
Q The mobile device cannot receive notification
Adjusting the surveillance angle
Loosen the adjusting screw and adjusting knob.
Adjust the surveillance angle to your desired place.
Tighten the adjusting screw and adjusting knob
to secure position.
Adjusting Knob
Adjusting Screw
i Make sure the microSD card slot is facing downward
for waterproof performance when you adjust the
camera surveillance angle.
Adjusting Screw
Adjusting Knob
prompts when the camera is online.
A Make sure the Côr Smart Home app is running on
Network
Interface
your mobile device, Motion Detection is enabled and
Notifications are turned on.
Android users should make sure the app is running
in the background.
iOS users should enable the message push function
in “Settings > Notification.”
If alarm prompts still fail to appear, hold down the RESET
button for 10 seconds to restore the camera settings to
factory default. (Note: you will need to set up Wi-Fi again.)
microSD
Card Slot
ADDITIONAL SUPPORT
microSD
Card Slot
Q Live view or playback failed.
A Make sure your network is well-connected. Viewing live
video needs a good bandwidth. You can refresh the video
or change network and try again.
Q How to connect to a new Wi-Fi network.
A Hold down the RESET button on the camera for
10 seconds to reset and restart the camera.
Reconnect the Wi-Fi by following the in-app steps.
Questions/Comments?
We want to hear from you!
SEE YOUR HOME IN A
WHOLE NEW WAY.
Call us: 844-692-6746 or
(844) MY-COR-HOME
Visit mycorhome.com.
Power
Input
microSD Card Slot
For microSD card (not included with this product).
Recommended compatibility: Class 10, maximum
space 128GB.
RESET
Hold down the RESET button for 10 seconds when
the camera is running. The camera will restart and
reset all camera settings to default.
Network Interface
10M/100M Self-adaptive Ethernet Interface supports
the PoE (Power of Ethernet) additionally.
Power Supply
1A ––– 12V
©2018 Côr™ Home Automation.
Wi-Fi® is a registered trademark of the Wi-Fi Alliance Corporation.
Apple and the Apple logo are trademarks of Apple Inc.,
registered in the U.S. and other countries. App Store is a service
mark of Apple Inc. Google Play is a trademark of Google Inc.
Android is a trademark of Google Inc. Other trademarks and logos
mentioned are the properties of their respective owners.
CTSTO-WH
IM-CTSTO-WH-01
CÔR™ OUTDOOR WI-FI ® CAMERA
1080P FULL HD
QUICK-START GUIDE
SET UP THE CAMERA
USING A WI-FI ® SMART DEVICE
CÔR™ CAMERAS HAVE BEEN DESIGNED TO PROVIDE
COMFORT AND PEACE OF MIND. USING THEM IS
EASY AND INTUITIVE: JUST INSTALL THE CÔR
SMART HOME APP ON YOUR SMART DEVICE AND
FOLLOW THESE SIMPLE STEPS FOR SETUP. ONCE
THE APP IS INSTALLED, YOU CAN COMMUNICATE
Connect your smart device to Wi-Fi.®
Download and install the free Côr™ Smart Home app
from the iPhone App Store or Android Google Play™
Open the Côr Smart Home app.
AND STAY CONNECTED FROM ANYWHERE.
WHAT’S INSIDE
Côr™ Outdoor Wi-Fi® Camera,
Quick-Start Guide/Installation Instructions,
Power Adapter, Power Adapter Extension Cable,
Mounting Template, Screws and Wall Anchors
Look for this Côr
Smart Home app icon
POWER ON THE CAMERA
Option 1: Connect the power cable to a power source.
Network Cable
Power
Source
Power Cable
Set up the camera
Create a new user account.
		Touch
SIGN UP FOR AN ACCOUNT on the login
		 page of app and follow the steps to create a profile.
B Then on the main menu, touch ADD NEW DEVICE.
If you already have a user account.
A Sign in to your account.
B Then on the main menu, touch ADD NEW DEVICE.
Turn on or enable Motion Detection to have the
camera record when motion occurs and to set up push
notifications and sound alerts. Touch NEXT.
		 If you opt to not enable motion detection,
		touch NEXT.
Push-Notification setup
Turn on or enable Push Notifications if you wish to
receive notifications when motion has been detected.
Touch NEXT.
		 If you opt to not enable notifications, touch NEXT.
Confirm or enter the six-digit verification code found on
the back of the camera. Touch NEXT.
On the same screen, turn on or enable Use Schedule.
Touch NEXT.
Verify serial number and touch CONFIRM DEVICE.
If you haven’t already, turn on the camera, select YES
and touch NEXT.
		 To turn on the camera, plug the power cable into the
		 USB adapter. Plug the USB power adapter into a
		 power outlet. When the indicator flickers red or blue,
		 the camera is ready for setup.
If you already have a thermostat set up on this app,
you can use your thermostat schedule to specify periods
when you will receive motion alerts.
Select the camera image and touch SETUP CAMERA.
Scan the QR code or manually input the nine-digit
serial number, both located on the back of the camera.
Create a user account (if you do not have one already)
Option 2: (Only for PoE models) Connect the
network cable to the PoE switch, not included.
PoE Switch
Download the app
INSTALLING THE CAMERA
Motion-Detection setup
A Click Thermostat Schedule to enable the Thermostat
		Periods you would like to use and touch SAVE.
		Touch
SKIP if you choose to not enable any
		of the Thermostat Periods.
Confirm the device you are using is connected to the
Wi-Fi® network you want your camera to connect to and
touch NEXT.
Hold your mobile device within 2 inches of the camera
to transfer Wi-Fi credentials.
Once your camera is successfully added, touch
CONFIGURE SETTINGS.
Read and accept the Terms and Conditions agreement.
10
Select the Time Zone and touch NEXT.
11
Name your camera by selecting a name or creating a
custom name. Touch NEXT.
C Click Custom Schedule if you would like to
		 set up a custom schedule. Once the schedule is
		complete, touch SAVE & CONTINUE SETUP.
i Make sure the wall is strong enough to withstand three
times the weight of the camera and the mounting.
i If the wall is cement, you must insert expansion screws
before you install the camera.
i If the wall is wooden, you can use self-tapping screws
to secure the camera.
The camera can be installed on the wall or ceiling.
The instructions below are for wall mounting.
Mounting template
Stick the mounting template where you plan to
install the camera.
Drill the holes according to the mounting template.
Route the camera cables through the mounting
base and wire the cables through the side opening.
Affix the mounting base to the wall with the
supplied screws.
Installing the camera
D If you opt to not enable Use Schedule,
		touch NEXT to continue.
To receive push notifications, touch ALLOW when told
“Côr Smart Home Would Like to Send Push Notifications.”
Turn Sound Alerts on or off and touch FINISH.
Congratulations, you have completed
the setup of your Côr™ camera.
Side
Opening
QUICK-START GUIDE
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Attention that changes or modification not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This product has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This product generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this product does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different 		
from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum
distance 20cm between the radiator and your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Language                        : en-US
XMP Toolkit                     : Adobe XMP Core 5.6-c143 79.161424, 2017/09/22-11:52:47
Create Date                     : 2018:04:03 15:41:50-04:00
Metadata Date                   : 2018:04:03 15:41:51-04:00
Modify Date                     : 2018:04:03 15:41:51-04:00
Creator Tool                    : Adobe InDesign CC 13.1 (Macintosh)
Instance ID                     : uuid:0b685799-e2c8-cd48-a05d-7c5ab8a8131b
Original Document ID            : xmp.did:f9ed83a0-9706-4cd7-bc88-2c3be0c1de49
Document ID                     : xmp.id:3121a6ab-10f1-4492-93cb-c49976631751
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:9dd67408-fe28-4f0d-bce5-46b653a5615a
Derived From Document ID        : xmp.did:65b88138-c4a0-4745-a70e-d71baf332d7c
Derived From Original Document ID: xmp.did:f9ed83a0-9706-4cd7-bc88-2c3be0c1de49
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 13.1 (Macintosh)
History Changed                 : /
History When                    : 2018:04:03 15:41:50-04:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Slug Family                     : Pier Sans
Slug Version                    : 1.000
Slug Outline File Size          : 0
Slug Kerning Checksum           : 0
Slug Foundry                    : --
Slug Font Kind                  : OpenType - PS
Slug Checksum                   : 3186110871
Slug Post Script Name           : PierSans-Regular
Slug Font Sense 12 Checksum     : 3186110871
Page Count                      : 3
Creator                         : Adobe InDesign CC 13.1 (Macintosh)

EXIF Metadata provided by EXIF.tools