Casablanca Fan Company Panama 6643Z Users Manual

6688Z to the manual af492b88-9672-4aa6-9cfc-bd1409ddee75

: Casablanca-Fan-Company Casablanca-Fan-Company-Panama-6643Z-Users-Manual-534938 casablanca-fan-company-panama-6643z-users-manual-534938 casablanca-fan-company pdf

Open the PDF directly: View PDF .
Page Count: 22

1

P/N 6643Z HN0210

BEFORE YOU START .....................................................................................................................................................................5

SAFE USE........................................................................................................................................................................................5

MOUNTING RECOMMENDATIONS ................................................................................................................................................6

SLOPED CEILING INSTALLATIONS ..............................................................................................................................................6

GETTING STARTED ........................................................................................................................................................................7

CROSSBAR MOUNTING BRACKET INSTALLATION ...................................................................................................................7

LAG SCREW INSTALLATION (OPTIONAL) ...................................................................................................................................8

 ....................................................................................................................................................... 8

FAN PREPARATION ........................................................................................................................................................................8

 ....................................................................................................................................................................9

CANOPY INSTALLATION ...............................................................................................................................................................9

 ........................................................................................................................................................................9

CANOPY ELECTRICAL CONNECTIONS ..................................................................................................................................... 10

 ................................................................................................................................................10

 ....................................................................................................................................10

4-SPEED OPERATION .................................................................................................................................................................. 11

 ........................................................................................................... 11

 ........................................................................................................................... 11

 ......................................................................................................................... 11

 ........................................................................................................................ 12

 .................................................................................................... 12

 ...................................................................................................................................15

SINGLE W-85 INSTALLATION ......................................................................................................................................................15

DUAL W-85 INSTALLATION ......................................................................................................................................................... 16

OPERATION SPEED CONTROL ..................................................................................................................................................17

OPERATION REVERSING AIRFLOW ...........................................................................................................................................17

 ....................................................................................................................................................................17

OPERATION POWER ....................................................................................................................................................................17

AUTOMATIC DEMONSTRATION PROGRAM ..............................................................................................................................18

 ............................................................................................................................................18

® PROGRAM .....................................................................................................................................19

®® PROGRAM .................................................................................................. 19

OPERATION FAN-MINDER PROGRAM ..................................................................................................................................... 20

 ..........................................................................................................................................................21

Safety and the proper operation of your Casablanca fan both require a thorough knowledge

of the product and proper installation; therefore, before attempting to install and operate your

Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for

future reference.

CAUTION: To avoid possible electrical shock, make certain that electricity is turned off

at the circuit breaker or fuse box before attempting any installation procedure.

Panama® Owner’s Manual



CONTENTS

2



Plate



Please take a moment to locate the model number and serial number from your fan (see below)

and record this information on the Warranty page inside the front cover of your Owner’s Manual

if it does not appear there already. These numbers are found on the motor identication plate

afxed to the fan motor in the location shown below:



Your Casablanca fan was crafted with pride and care and inspected thoroughly

prior to shipment. Before you begin to assemble and install your Casablanca

fan, remove all parts from the carton and

check them against the Parts Guide in this

manual.

Make sure all parts are included in the box

using the Parts Guide on the following

pages.

If there are missing or broken parts:

Call 1-888-227-2178 Monday through Friday, 7 a.m. to

4 p.m. PST. Your request will be handled immediate-

ly. Replacement parts will be sent to you via Federal

Express.



Do not remove lightbulbs from their packaging until

you are ready to install them.

Before discarding packaging materials, be certain that

all parts have been removed.

Use a clean, dry paintbrush to remove small Styro-

foam pieces that may remain after unpacking.

Do not brush Styrofoam into wiring cavities.

The blades in each pack are matched for equal weight

to assure smooth fan operation. If more than one fan

is being installed, do not mix blades from different

cartons.

When cleaning, painting, or working near your fan, be

cautious of the fan and blades.

Always turn power to the ceiling fan OFF before re-

placing lightbulbs or working on your fan.

Never insert anything into the path of the fan blades

while the fan is in operation.

Never install a fan over a pool or spa.

Never operate a fan that has been damaged in any

way.

Install the fan according to the instruc-

tions in this manual.

If the fan does not work:

Refer to the Troubleshooting Tips in this Owner’s

Manual.

Call Technical Support at 1-888-227-2178.

Contact your local Authorized Service Center.

Our Web site at www.casablancafanco.com

contains additional information on Casablan-

ca products, troubleshooting, and Authorized

Dealer or Service Centers. Please do not

return this product to the store.

Serial Number

®

  

DJ01 1151 MODEL #66xxG/Z or

66DxxG

POMONA, CA

SERIAL No.: DJ06 2237

66xxZ Model Number

3

Panama®

Item # Description Picture (not to scale) Quantity

1. Motor Housing 1

2. Ceiling plate 1

3. Phillips Screwdriver 1

4. 11/2" x 8-32" Roundhead screws and Washers , 2 EA

5. Screw Pack:

Lag Screw and Washer (1) 1 EA

6. Wire Nuts (4), 4

7. Canopy and Canopy Hatch 1

8. Perma•Lock™ Downrod

and Ball Assembly 1

9. Canopy Screws and Lock Washers, 5 EA

10. Allen Wrench 1

PARTS GUIDE

4

Item # Description Picture (not to scale) Quantity

11. Blade Irons 5

12. Blade Iron Screws 11

13. Blade Screws and Washers 16 EA

14. Light Pull Chain Switch (G model only) 1

15. Light Pull Chain Fandangle (G model only) 2 -(66xxG)

3 -(66DxxG)

16. W-41 Single Rotary (optional for G model only) 1

17. W-81 Dual Rotary (optional for G model only) 1

18. W-85 Control and Mounting Hardware (Z model only)

`

1

5

Panama®

Circuit Breaker

(Trip breaker for the

circuit you will be

working on)

Fuse Box

(Remove fuse for the

circuit you will be

working on)

18"

70"

SAFE USE

 CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical

Code, ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a

qualied electrician. To avoid overheating and possible damage to other equipment, do not install control to a

receptacle, uorescent light xture, motor-operated appliance, or transformer-supplied appliance.

• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for

ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are available for

sloped or high ceiling installations.

 This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum

current requirement for the fan with light xture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light

current is 2.8 amps or 340 watts of lighting.

 Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy

hatch, make sure all wires are within the canopy and that no wires are being pinched.

 WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning

the fan. Do not insert foreign objects in between the rotating fan blades.

Unpacking

Before assembling and installing your ceiling fan, remove all parts from the shipping cartons

and check them against the parts listed in the Parts Guide. Before discarding packaging ma-

terials, be certain that all parts have been removed.

For best performance and for your warranty to be valid,



Introduction

 The blades in each pack are matched for equal

weight to assure smooth fan operation. If more

than one fan is being installed, be careful not to mix

blades from different cartons.

 Inspect the contents of your carton for possible

shipping or handling damage. If parts are missing

or damaged, call 1-888-227-2178.

 It is always a good idea to have an assistant to help

with the installation.

 When cleaning, painting, or working near your fan,

be very careful of the fan and blades. Always turn

the power OFF to the ceiling fan before working on

it or replacing lightbulbs.

 Never insert anything into the path of the fan

blades while the fan is in operation.

• Never install a fan over a pool or spa.

 Never operate a fan that has been damaged in any

way. Contact Casablanca Fan Company by calling

1-888-227-2178, or contact your local authorized

Casablanca dealer for assistance in obtaining

service.

BEFORE YOU START

84"

6

MOUNTING RECOMMENDATIONS

SLOPED CEILING INSTALLATIONS

Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air

circulation, and fan size are all important factors to consider before installation.

Location

Ceiling fans have practical uses in almost every room in your home.

We suggest you follow these mounting recommendations as you

decide where to install your Casablanca fan.

• For safety reasons, the fan blades must be a minimum of 7' above

the oor.

• Do not locate the fan in a doorway or above a swinging door.

• In bedrooms, fans work best when mounted above the foot of the

bed.

• Over pool tables, be sure to provide plenty of clearance to avoid

damage from pool cues.

• In kitchens be sure to allow for open cupboard doors to clear the fan

blades.

• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy

the nish and warp the blades.

Fan Size

Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms,

two fans may be needed.

Calculation of Ceiling Angle

Use the tear-off Ceiling Angle Template

card inserted in this manual. It provides

you with a simple “go” or “no-go” for install-

ing your fan on a sloped ceiling.

7' minimum

When to Use Extension Poles

For optimum performance and appearance, an ex-

tension pole should be used with your Casablanca

fan when installing on high (cathedral) ceilings or

sloped ceilings. Casablanca offers standard poles

in increments of 6" up to 5'. Custom poles are

available in lengths up to 9'9". See your Authorized

Casablanca Dealer for details.

Blades must be a

minimum of 7 feet

above the oor

Extension

Pole

Maximum

Hang-Tru®

angle 32º

This slope is less than 32º.

It is OK to install your fan.

This slope is 32º. This is the maximum

slope that will allow the fan to hang

straight down. It is OK to install your fan.

This slope is more than 32º. Your fan will not

hang straight down, an adaptor is necessary.

Contact your local Authorized Casablanca

Dealer in regards to purchasing a “Sloped

Ceiling Adaptor.”

NOTE: Fan may wobble or vibrate if pole length is

not long enough and inside blade is too close to

downslope or side wall. Extending pole length will

usually solve problem.

SUGGESTED EXTENSION POLE LENGTHS

Ceiling Height Pole Length

8' 0" standard

8' 6" standard

9' 0" 6"

9' 6" 12"

10' 0" 12"

11' 0" 18"

12' 0" 24"

13' 0" 36"

14' 0" 48"

EXAMPLE 3

EXAMPLE 2

EXAMPLE 1

ceiling outlet

box

support

brace

standa rd

mounting

style

7

Panama®

Using Existing Ceiling Fixture Outlet Box

After turning the power OFF at its source (either

the circuit breaker or fuse box), lower the old xture

and disconnect the wiring. Check the ceiling xture

outlet box to be sure it is marked “Approved for

Ceiling Fan Mounting.” If it is not, a new box must

be installed.

GETTING STARTED

Installing a New Ceiling Fixture Outlet Box

If you do not have an existing xture located where

you wish to place your Casablanca fan, an ap-

proved ceiling xture outlet box must be installed

and wired.

Note: The weight of this fan is 24 to 26 pounds,

depending on model.

WARNING!

To reduce the risk of re, electrical shock, or

personal injury, mount to outlet box marked

“Acceptable Fan Support of 22.7 kg (50

lbs.) or less” using the mounting hardware

provided with the outlet box.

CEILING HARDWARE (not to scale)

WARNING!

Support directly to building structure only.

CROSSBAR MOUNTING BRACKET INSTALLATION

Note: After removing the old xture, check the outlet

box to insure that it is supported by a joist or beam

across its upper surface. If not, a 2 x4 stud must be

installed.

Step 1a. Remove the knockout plug in the center

of the outlet box or drill a 1/2-inch hole for the lag

screw to pass through. Then drill a 1/4-inch guide

hole into the joist or beam to a depth of 3 inches.

Step 1b. Route the outlet box wires through the

keyhole slot of the crossbar mounting bracket as

shown. Attach the crossbar mounting bracket to the

outlet box with the screws provided, making sure

the outlet box wires are not pinched by the washer.

CAUTION:

To reduce the risk of personal injury, use only

the mounting hardware provided with the

approved outlet box to install the crossbar

mounting bracket.

Crossbar Mounting Bracket

Lag Screw and Washer (1)

1" x 8-32 Roundhead Screw and Washer (2)

21/4" x 8-32 Roundhead Screw (2)

Wire Nut (4)

Joist

Ceiling-Fan-

Approved

Wiring Box

Ceiling Wiring

Crossbar

Mounting Bracket

Green Ground Wire

Ridge side down

1" x 8-32

Roundhead Screw

Washer

FAN INSTALLATION

CAUTION:

Damp Location rated fans required a Ground

Fault Interrupter(GFI). use a weather-proof

outlet box, properly connect ground wires,

and use only under a weather-proof structure

8

Prepare for fan installation as follows:

3a. Route the wires from the motor through the PermaLock™

downrod and ball assembly.

3b. Using the provided allen wrench, loosen the set screw

several turns to allow installation of the downrod. Thread

the downrod into the motor coupling until it stops turning,

this will take at least four and a half full turns.

3c. Securely tighten the set screw with the provided allen

wrench to ensure safe operation of your fan.

Tip: The downrod has a tapered thread

that is designed to lock completely when

correctly installed.

CAUTION: Failure to fully lock in the down-

rod before securely tightening the set screw

may cause the fan to separate from the

downrod during normal operation!

MOTOR

COUPLING

TAPERED

THREAD

MOTOR

WIRES

GROUND

WIRE

ALLEN

SET SCREW

DOWNROD

& BALL

ASSEMBLY

FAN PREPARATION

IMPORTANT SAFETY INFORMATION!

BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE

THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY

DOWNROD & BALL

ASSEMBLY



ALLEN SET SCREW

1⁄420 x 1⁄4”

PREINSTALLED

LAG SCREW INSTALLATION OPTIONAL

NOTE: This step is required only under two condi-

tions: If the fan weighs 36 lbs. or more (which does

not pertain to this fan) or if the existing ceiling

xture outlet box needs to be modied for a ceiling

fan application (for example, if the house is not new

construction and you are replacing an existing light

xture). We recommend that the ceiling box be of

sufcient capacity to support the weight of the fan

and light xture under any conditions. If in doubt

whether you need to install the lag screw, consult a

qualied electrician.

Step 2 (optional). With the large washer attached,

pass the lag screw (Pack A) through the center hole

of the crossbar mounting bracket and screw into the

guidehole. Tighten until the outlet box is mounted

rmly to the beam. This box must be secured to the

ceiling rmly.

LAG

SCREW

LARGE

WASHER

1/8"

ALLEN WRENCH

9

Panama®

Step 5. To hang the fan body in the

canopy, hold the fan body rmly and

insert the ball into the canopy open-

ing. Check that no wires were pinched.

Rotate the fan body until the slot in the

nylon ball ts into the pin opposite the

canopy opening.

NOTE: Independent control of the

light xture using a W-81 accessory

control requires an additional pow-

er wire run from the wall switch to

the fan. See Page 12 for wiring.

CAPPED

BLUE

D1OPTION

WIRE ON

3SPEED ONLY

FOR LIGHT

CONTROL PINSLOT

BALL

CANOPY

HATCH

CANOPY LOCK WASHER 5

CANOPY SCREW 5

Step 4. Attach the canopy to the crossbar mounting bracket with three of

the 8-32 x 21/2” long canopy screws and lock washers provided with your

Casablanca fan. Hand tighten until snug against the ceiling.

CANOPY

SCREW

CANOPY

LOCK

WASHER

FEED OUTLET BOX

WIRES THROUGH

CANOPY OPENING

Note: On sloped ceilings, align the

canopy opening toward the top or

peak of the room.

CANOPY HARDWARE

HANGING THE FAN

CANOPY INSTALLATION

CANOPY

10

Step 6a. Attach the fan wires to the ceiling xture outlet

box wiring by twisting the bare ends of the wires together

and then securing with a wire nut. Test that the connection

is secure by pulling on the wire nut. Connect in this order:

Step 6b. W-85 Wiring Connections

 

conductor of power source. Secure with wire nut.

 

xture outlet box. Secure with wire nut.

 -

ing outlet box. Secure with wire nut.

Step 6c. Pull Chain Connections

 

conductor of power source. Secure with wire nut.

 

xture outlet box. Secure with wire nut.

 

ceiling outlet box and the BLUE wire form light kit. Secure

with wire nut.

 

outlet box. Secure with wire nut.

2 WHITE WIRES

2 BLACK

WIRE NUT

PULL CHAIN

CONNECTIONS

3 GREEN WIRES

3 GREEN WIRES

2 WHITE WIRES

2 BLACK + 1 BLUE

W85 CONNECTIONS

Step 7. Tuck the wires into the canopy

with the wire nuts pointed upwards, so

that the WHITE and BLACK wires are on

opposite sides of the canopy and all wires

are clear of the canopy opening.

Step 8. Install canopy hatch with the

last canopy screw and lock washer. To

do this, tilt the fan body away from the

hatch opening.

Tighten the screws rmly by hand only,

TILT THE

FAN TO

INSTALL

LAST

CANOPY

SCREW

CANOPY

HATCH

CANOPY

SCREW

LOCK

WASHER

Step 9. Straighten the fan, then check

to ensure that there is no movement be-

tween the canopy and ceiling or Hang-Tru

ball and top support shaft.

CANOPY HATCH INSTALLATION

CANOPY ELECTRICAL CONNECTIONS

If you will be installing an accessory light kit, also connect

the BLUE light power wire from fan to the BLACK wires).

11

Panama®

PROCEED TO YOUR FAN’S CONTROL FEATURE SECTION FOR INSTALLATION/OPERATING INSTRUCTIONS:



BLADE/BLADE HOLDER INSTALLATION

Step 10. Attach the blades to the blade

holders with the three blade screws and

at washers provided for each blade.

Hand tighten securely.

Install the assembled blade and blade

holder to the fan motor.

Hand tighten securely.

Repete for each blade assembly. BLADE SCREW

3 PER BLADE

FLAT WASHER

3 PER BLADE

BLADE HOLDER SCREW

2 PER BLADE HOLDER

Your fan is equipped with a ywheel

that allows for both 4 and 5 blade

installation. The screw holes sur-

rounded by squares are for 4 blade

installation, while the screw holes in

circles are for 5 blade installation as

shown above.

WARNING: To reduce the risk of personal injury, do not bend blade holders

when installing, balancing, or cleaning. Do not insert foreign objects between

rotating fan blades.

12

Pull-chain switches on the fan control the fan and lights.

Using the fan control pull-chain switch: Fan o at start.

First pull: fan ON, High speed

Second pull: Medium speed

Third pull: Medium Low speed

Fourth pull: Low speed

Fifth pull: Fan OFF

Using the optional light pull-chain switch: Light o at

start.

First pull: light ON

Second pull: light OFF

Direction of blade rotation is controlled by the reverse slide

switch on the side of the switch housing.

No changes in household wiring are required.

COLLAR

SWITCH

HOUSING

1. Refer to light kit instructions to assemble and attach your light

kit correctly.

2. Remove the two 8-32 screws from the switch housing cap.

3. Remove the plug from switch housing.

4. Install pull-chain switch and nger tighten collar on switch.

5. Connect one wire from pull-chain switch to the BLUE D1-Option

wire. Secure splice with a wire nut.

6. Connect other wire from pull-chain switch to BLACK wire from light

kit. Secure splice with a wire nut.

7. Connect WHITE wire from switch housing to WHITE wire from light

kit. Secure splice with a wire nut.

8. At the canopy, connect the BLACK and BLUE wires.

The W-41 wall control provides four-speed control of fan from a convenient wall location.

The W-41 is designed to replace a standard wall switch and will t wall boxes with a depth

of 2” or greater. Not for use with single pull-chain fan/light option wiring.

To install a W-41 wall control in place of an existing wall switch, follow the instructions

on the W-41 package.

Note: No rewiring is required if the fan is replacing an existing light xture.

Operation of the fan from the wall switch is simple:

1. Turn knob to obtain desired speed setting.

R

The W-81 wall control provides separate control of fan and light with two separate knobs

from a convenient wall location. The W-81 is designed to replace a standard wall switch

and wall boxes with a depth of 2” or greater. Requires two hot leads from wall box to ceil-

ing wiring box.

To install a W-81 wall control in place of an existing

wall switch, follow the instructions on the W-81 package.

Operation of the fan from the wall switch is simple:

1. Turn the upper knob to the desired fan speed.

2. Turn the lower knob to the desired light setting.

OFF

LO

MED

MED

HI

HI

OFF MAX

CAUTION! Failure to set the pull-chain speed to HIGH can result in faulty operation of

the fan and damage to the W-41 wall control. To conrm fan is set to HIGH: Turn W-41

fan speed switch to ‘HI’ - set fastest fan speed with pull chain.

CAUTION! Failure to set the pull-chain

speed to HIGH can result in faulty operation

of the fan and damage to the W-81 wall

control. To conrm fan is set to HIGH: Turn

W-81 fan speed switch to ‘HI’ - set fastest

fan speed with pull chain.

NOTE: If a separate circuit is used to control the lights from a wall

control, the BLUE D1-Option wire in the canopy should be con-

nected to that switch leg.

OPTIONAL LIGHT

PULL CHAIN

SWITCH

REVERSE

SWITCH

FAN & SPEED CON

TROL

PULL CHAIN SWITCH

4SPEED OPERATION







BLUE D1

LIGHT FIXTURE

WHITE

BLACK

13

Panama®

R

 

by the W-81 wall control.

 

OFF by the W-81 and the intensity

adjusted from low to high.

 

two independent 120V AC supply

wires.

 

the HIGH speed setting.

 

 

(4) dierent speed settings.

 

dierent speed settings.

 

 

HIGH speed setting.

 

are required.

 

the W-41 wall control.

CAUTION! Failure to set the pull-chain

speed to HIGH can result in faulty

operation of the fan and damage to

the W-41 wall control. To conrm fan

is set to HIGH: Turn W-41 fan speed

switch to ‘HI’ - set fastest fan speed

with pull chain.

CAUTION! Failure to set the pull-

chain speed to HIGH can result in

faulty operation of the fan and

damage to the W-81 wall control.

To confirm fan is set to HIGH:

Turn W-81 fan speed switch to

‘HI’ - set fastest fan speed with

pull chain.

4SPEED





14

® 3

WALL CONTROL AND HARDWARE (not to scale)

Switch Mounting

Screws (2)

Wall Plate

Screws

(2) White

(2) Almond

White Wall

Plate(1)

W-85

Wall Control

Switch Bezels

(1) White

(1) Almond

Almond Wall

Plate(1)

(4) Wire Cap

Before installing the W-85 wall control you will need

to check and see if you will need to change the

bezel on the front of the wall control from WHITE to

ALMOND. If you are going to use white, skip these

steps and go to wall control installation starting on

page 15. The bezel can be changed at any time

before or after installation. The wall control does

not need to be uninstalled to replace the bezel.

W-85 Wall Control Bezel Replacement installation

as follows

Step 17a. Locate the four (4) tabs holding the bezel to

the front of the switch, then press in on each tab one

at a time, removing the bezel as shown in Figure #1.

Step 17b. Locate the rubber key pad attached to

the four (4) locating pins as shown in Figure #2 and

remove rubber key pad from the WHITE bezel, also

as shown in Figure #2.



To avoid possible electrical shock, make cer-

tain that electricity is turned off at the circuit

breaker or fuse box before attempting any in-

stallation or repair procedure

CAUTION! NOT turning the power OFF at the

circuit breaker or fuse box may cause damage to

the electronics within the wall control and or the PC

board on the fan.

Figure #2

WHITE

BEZEL

RUBBER KEY

PAD

LOCATING

PINS (4)

LOCATING

PINS

HOLES(4)

W-85 CONTROL INSTALLATION

Figure #1

BEZEL

BEZEL

TABS

15

® 3

LOCATING

PINS (4)

Figure #5

ALMOND

BEZEL

BEZEL

TABS

BEZEL

ALIGNMENT

PIN AND HOLE

Figure #3

ALMOND

BEZEL

RUBBER KEY

PAD

W-85 Wall Control Bezel replacement: -

CONTINUED

Step 17c. Reinstall the rubber key pad on to the

four (4) locating pins located on the almond bezel

as shown in Figure #3 and #4.

Step 17d. To attach the bezel back on to the front

of the switch you will need to align the four (4) tabs

on the bezel with the front of the wall control and

by gently pressing on both top and button of the

bezel at the same time, snap the bezel back on to

the front of the switch as shown in gure #5.

Step 17e. Check your work by pressing on the

light, fan, reverse and power buttons, making sure

that the buttons do not stick and that each switch

functions properly.

RUBBER KEY

PAD

ALMOND

BEZEL

Figure #4

LOCATING

PINS

(4)

16

® 3



W-85 CONTROL INSTALLATION

1. Use only the Casablanca W-85 wall control.

2. Do not use any additional control with your Inteli-

Touch 3 fan (for example, dimmer, or fan speed

control).

3. Do not use more than one fan per wall control.

4. No other light xtures or electrical appliances

may be connected on the circuit controlled by the

W-85 wall control.

W-85 is used to describe either white (-11) or almond nish.

If you have multiple Inteli-Touch 3 fans, refer to the section

"Changing Frequency Setting" on page 18.

1. Remove the screws and switch plate from the existing

switch box.

2. Remove the screws holding the switch in the switch

box.

3. Pull the existing switch from the switch box to expose

the wire connections.

4. Remove the two wires from the switch.

5. Connect the BLACK wire from the POWER SOURCE

that you just removed from the switch to the BLACK/

The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This

controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this

reason the following precautions must be observed:



Ensure power is turned OFF at the breaker or fuse panel before starting installation.

NOTE: The RED wire is not used in this ap-

plication, DO NOT remove the crimped cap

from the wire..



STRIPED WIRE

W-85

Wall Control

2 BLACK

WIRES

RED WIRE

NOT USED

(FIGURE #2)

(FIGURE #1)

NOTE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch® 3 fans with DOWNLIGHTS

ONLY.

WHITE STRIP wire on the W-85 wall con-

trol. Secure this connection with a wire nut.

6. Connect the second BLACK wire that you

just removed from the switch to the second

BLACK wire on the located on the back of

the W-85 wall control. Secure this connec-

tion with a wire nut.

7. Connect the green ground wire coming

from the back of the W-85 control to the

ground wire in the switch box. Secure the

splice with a wire nut.

8. Check your work by using the wiring dia-

grams as shown in Figures # 1 and #2.

9. Install the W-85 in the wall box with the

two long screws provided.

10. Install the wall plate with the two color-

matched screws.

SINGLE W85 INSTALLATION

W-85

17

® 3

DUAL W85 INSTALLATION

To control the fan and lights from two locations (a three-way circuit), use two W-85

wall controls as shown in the wiring diagram in Figure #5. Before installing the

two switches into the wall, place both switches side by side, then locate the 4 dip

switches on the side of the two switches. Then make sure that the dip switches

are set to the same address on both switches as shown in Figure #4. When setting

these dip switches you are setting the channel number that is required to control

both your fan and lights from both sides of the room. If you are installing other

Inteli-Touch® 3 fans within your home you may need to reset the dip switches on

these other fans to a different channel before installing your W-85 wall control into

the wall. Please review the section on channel changing on this instruction sheet.



(FIGURE #4)



Ensure power is turned OFF at the breaker or fuse panel before

starting installation.

To control the fan and lights from two locations (a three-way circuit), use two

W-85 wall controls.

1. Remove the screws and switch plate from the existing switch box

and the screws holding the switch in the switch box.

2. Pull the existing switch from the switch box to expose the wire con-

nections.

3. Determine which wire is connected to the common terminal from

the power source (120V AC) of the three-way switch. (The terminal

will be marked on switch).

4. Remove the wire from the common terminal of the three-way switch.

Connect this wire to the remaining black/white striped wire on the W-85

control. Secure this splice with a wire nut.

5. Remove the two remaining wires from the three-way switch. Con-

nect the black wire of these wires to a black wire on the W-85 control.

Secure the splice with a wire nut. The remaining red wire is to be con-

nected to the other red wire on the

W-85. Secure the splice with a wire nut.

6. Connect the green ground wire coming from the back of the W-85 con-

trol to the ground wire in the switch box. Secure the splice with a wire

nut.

7. Check your work by using the wiring diagrams as shown in Figure #5

on this page.

8. Install the W-85 in the wall box with the two long screws provided.

9.Install the wall plate with the two short color-matched screws provided.

10.Installation of the second W-85 control is identical. Repeat steps 1 through 9.

W-85

Wall Control



STRIPED WIRE

2 RED WIRES

2 BLACK

WIRES

(FIGURE #5)

W-84

BLACK

BLACK

BLACK

BLACK

BLACK

BLACK

BLACK

RED

GREEN

120V AC

BLACK

BLACK WITH

WHITE STRIPE

W-84

RED RED

RED

BLACK WITH

WHITE STRIPE

GREEN

NEUTRAL

WHITE

GREEN

W-85 W-85

18

® 3 OPERATION POWER

The button is normally left in the on position. Always turn the power off

during cleaning or servicing the fan and during thunderstorms. It is also used to

exit or enter additional programs.

The button must be left on to retain a previously set fan speed or light level.

OPERATION SPEED CONTROL

FAN CONTROL

ON - OFF:

A momentary

press of the FAN

button

CHANGE SPEED:

Press and hold

FAN button longer

than one second

There are six individual speed settings for the fan; each speed is indicated

by an audible tone of increasing pitch.

To select the desired fan speed:

1. With fan off, press and hold the button labeled . The fan blades

will start rotating at the slowest speed, and will increase in steps.

2. Release the button when the desired speed is reached.

The fan speed is now in memory and will automatically come on at the

same speed each time the button is used. To maintain this level

of speed, turn the fan on by pressing less than one second. To

lower speed, turn fan off, then on by pressing and holding the

button until the desired speed is reached. When the fan is on, you may

increase the speed by pressing and holding the button until the

desired speed is reached, then release it.

OPERATION REVERSING AIRFLOW

The direction of airow can be changed from down-

ward to upward or from upward to downward.

To reverse the airow:

1. Make sure the is on and blades are Turn-

ing.

2. Press the button.

Note: A four-toned signal

indicates the command was

accepted by the fan. A few

seconds later the fan will slow

to a stop and then reverse

direction.

LIGHT CONTROL

ON - OFF:

A momentary press of

the  button

-

NESS:







SECOND

To turn the lights off and on, press and release the button for less than

one second.

1) First press/release of the button- The light will turn ON.

2) Second press/release of the button- The light will turn OFF.

To vary the light brightness at each touch level:

To vary the light brightness:

1. With lights off, press and hold the button. After one second the lights will

come on at their lowest level and gradually become brighter.

OPERATION LIGHTS

NOTE: Light Operation - the light varies from “bright” to “dim” over

approximately 8 seconds. This sequence will reverse the light when it

reaches the brightest or dimmest level if you continue to hold the LIGHT

button. Release the button when the desired level is reached.

2. Release the button when the desired brightness level is reached.

The brightness level is now in the fan memory and will automatically come on at

the same brightness the next time the button is used.

19

® 3 CHANGING FREQUENCY SETTING

NOTE: All fans leave the factory set to

“1111”

You will only have to change the dip switch settings in the remote if you

are using more than one fan in the same area and want to control them

separately.

DIP





SET TO ‘1111’

(Factory Setting)



SET TO ‘1001’

AUTOMATIC DEMONSTRATION PROGRAM

A multi-tone signal will verify the start of the test pro-

gram which proceeds as follows:

• Lights slowly increase to full intensity.

• Fan accelerates to speed three with audio tones.

• Light dims to half intensity.

• Fan accelerates to full speed with audio tones.

• Fan reverses at full speed with audio tones.

• Fan operates at full speed.

• Fan turns off with audio tones (blades coast for a

short time).

• Lights turn off.

The complete cycle lasts slightly over one minute. It

will continue to repeat until the is turned off

for more than ve seconds, cancelling the program.

Programmed into every Inteli-Touch® 3 Series fan is

an Automatic Demonstration Program. It can be used

to fully demonstrate and test the operation of the fan.

To enter the demonstration program:

1. Turn off for at least 5 seconds. This will

clear the fan memory ready for programming.

2. Turn on.

3. Immediately operate the buttons in the following

sequence:

+++ +

NOTE: DO NOT set dip switch setting in the remote

to ‘0000’, this may cause frequency interference

from other Casablanca Products.

Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle

switch, for the fan you want to change.

Step 2. Remove the screws and switch plate from the existing switch box.

Step 3. Remove the screws holding the switch in the switch box.

Step 4. Pull the existing W-85 switch from the switch box to expose the dip

switches located on the side of the control as shown in Figure #1.

Step 5. Change the dip switch settings, assuring that they are different from

the previously installed Inteli-Touch® 3 fan.

Step 6. Mount the W-85 Wall Control unit back into the wall electrical box.

Step 7. At the circuit breaker or fuse box and at the toggle switch, turn the

power off for the fan whose frequency you are changing.

Step 8. Within 20 seconds of restoring power to the ceiling fan and the

W-85 Wall Control press and hold both the “FAN” and “REVERSE” buttons

as shown in Figure #2 for 3 seconds, you will hear one tone from the Piezo

Buzzer indicating the command has been accepted.

20

® 3

OPERATION HOMESAFE® PROGRAM

The  makes an unoccupied home appear occupied by turning

the lights on and off at random times.

To enter the Home-Safe Program:

1) To operate the lights and fan for Home Safe Program – Press the But-

ton off for a least 5 seconds.

2) Turn the on. Immediately press the buttons in the following sequence:

+ + + . A series of tones will be heard through the

piezo-buzzer and ashing lights indicating the command has been accepted will

follow. This program overrides all manual control of lights and fan. Once the lights

turn on, they will automatically turn off after 2 hours.

3) The lights will automatically cycle on and off in a controlled sequence as follows:

ON 1 hour, OFF ½ hour, ON 2 hours, OFF 1 hour, ON ½ hour then OFF 2 hours.

This seven hour pattern will repeat continuously so that a different pattern of lighting

is seen each day of the week.

4) To cancel the Home-Safe Program, press the Button OFF for ve

seconds.

OPERATION SAFEEXIT® AND LIGHTMINDER® PROGRAM

NOTE: Both Light-Minder and Safe-Exit programs will always run at the same

time.

The Light-Minder Program automatically turns OFF the fan mounted lights after two

hours.

To enter the Light-Minder Program:

1) To operate the lights for Light Minder Program – Press the button off for at

least 5 seconds.

2) Turn the on. Immediately press the buttons in the following sequence:

+ + + . A series of tones will be heard through the piezo-

buzzer indicating the command has been accepted. Once the lights turn on, they will

automatically turn off after 2 hours.

3) Light operation still remains normal, if you leave the room and turn OFF the lights

will blink to indicate this Safe-Exit command has been accepted. The lights will stay

on for 30 seconds and then begin to dim. After thirty seconds have elapsed, the lights

will turn completely off.

4) To cancel the Light-Minder and Safe-Exit Programs, press the button.

The Safe-Exit Program gives you about thirty seconds of light when you turn the

lights off, enabling you to exit your home before the lights go out. To enter the Safe-

Exit Program:

1) To operate the lights for Safe-Exit Program – Press the button off for at

least ve seconds.

2) Turn the Power on. Immediately press the buttons in the following sequence:

+ + + . Immediately press the Button after an audio tone

is heard from the fan controller. The lights will blink to indicate this command has been

accepted. The lights will stay on for 30 seconds and then begin to dim. After thirty

seconds have elapsed, the lights will turn completely off.

3) To cancel the Safe-Exit Program, press the button off for ve seconds.

NOTE: If the lights are left on in the room, the lights will automatically turn

OFF after 2 hours. ( this is Light-Minder)

Light-Minder

Safe-Exit

21

® 3

OPERATION FANMINDER™ PROGRAM

The Fan-Minder feature will add to your comfort when used in the bedroom. The program

reduces the speed of the fan each two-hour interval to compensate for cooling night air.

To enter the Fan-Minder Program:

1. Turn the OFF for at least 5 seconds.

2. Turn the ON.

3. Immediately operate the buttons in the following sequence:

+ + +

4. The fan will respond with three descending tones. A timer is now initiated and the fan will

reduce one speed for each two-hour interval. The fan will not, however, descend below

the second lowest speed.

5. You may increase the fan speed by pressing and holding the button until the

desired speed is reached, then release it. The fan will again reduce one speed for each

2 hour interval.

5. To cancel the Fan-Minder Program, turn the OFF for three seconds.

22

® 3

Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.

TROUBLESHOOTING TIPS

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device

may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired

operation of the device.

1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver,

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or

an experienced radio/TV technician for help. Note: Any changes or modications to the transmitter or receiver not expressly

approved by Casablanca Fan Company may void one’s authority to operate this remote control.

PROBLEM POSSIBLE REMEDIES

Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position.

Check all wire connections. Make sure the power is turned off during this

inspection.

• Pin connectors are not making good contact. Check all connections.

• The fan receiver is defective. Replace the fan receiver.

• Reset the frequency setting: Turn the power off at the circuit breaker

for the fan that is not functioning only. Within 20 seconds from restoring

power to the ceiling fan and the W-85 Wall Control press and hold both

the “Fan” and “REVERSE” buttons as shown in Figure #2 for 3 seconds,

you will hear one tone from the Piezo Buzzer indicating the command

has been accepted. The Fan will come on at “low” speed in the reverse

direction.

Fan wobbles or shakes excessively • Be sure the canopy pin is set properly into the slot on the ball.

• Check that the blade holders have not been bent during installation and

the blades are balanced.

• The hanger bracket and/or the ceiling outlet are attached too loosely.

Make sure the hanger bracket is attached tightly to the ceiling outlet box

and the downrod assembly is secured rmly.

• The downrod is attached to the downrod base too loosely. Make sure all

the screws are securely tightened.

Fan is noisy during operation • When changing fan speeds, you may hear several audible clicks. This is

normal operation.

• Check and tighten the light xture retaining screws, glass shade screws,

and/or lightbulb(s).

• Tighten the canopy screws and mounting plate assembly. Make sure

the wire nuts inside the canopy and switch housing are not touching the

metal parts and that they have not fallen off the wire splices. Tighten as

necessary.

• Tighten the blade holders to the ywheel (or Direct Drive motor) and the

blades to the bladeholder screws.

• Make sure all the screws in the motor housing are snug but not overly

tight.

Fan does not run on low speed • If fan is new, it may need to be “broken in.” Run at high speed for several

days.