Casio 5269 Operation Manual QW

2014-12-12

: Casio Casio-5269-Operation-Manual-119412 casio-5269-operation-manual-119412 casio pdf

Open the PDF directly: View PDF .
Page Count: 9

Download
Open PDF In Browser	View PDF

MO1208-EA

Operation Guide 5269
ENGLISH
Congratulations upon your selection of this CASIO watch.

Warning!
• The measurement functions built into this watch are not intended for taking
measurements that require professional or industrial precision. Values produced
by this watch should be considered as reasonable representations only.
• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of
this product or its malfunction.

E-1

About This Manual
• To ensure correct direction readings by this watch, be sure to perform
bidirectional calibration before using it. The watch may produce incorrect
direction readings if you do not perform bidirectional calibration. For more
information, see “To perform bidirectional calibration” (page E-36).
• Keep the watch away from audio speakers, magnetic necklace, cell phone,
and other devices that generate strong magnetism. Exposure to strong
magnetism can magnetize the watch and cause incorrect direction readings. If
incorrect readings continue even after you perform bidirectional calibration, it
could mean that your watch has been magnetized. If this happens, contact
your original retailer or an authorized CASIO Service Center.

• Depending on the model of your watch, digital display
text appears either as dark ﬁgures on a light
background, or light ﬁgures on a dark background. All
sample displays in this manual are shown using dark
ﬁgures on a light background.
• Button operations are indicated using the letters shown
in the illustration.
• Note that the product illustrations in this manual are
intended for reference only, and so the actual product
may appear somewhat different than depicted by an
illustration.

E-2

E-3

Things to check before using the watch
1. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “Conﬁguring Home City Settings” (page E-17) to conﬁgure
your Home City and daylight saving time settings.

3. Set the current time.
See “Conﬁguring Current Time and Date Settings” (page E-22).
The watch is now ready for use.

Important!
Proper World Time Mode, Sunrise/Sunset Mode, and Moon Age Mode data depend
on correct Home City, time, and date settings in the Timekeeping Mode. Make sure
you conﬁgure these settings correctly.
2. Conﬁgure latitude and longitude settings for your current location.
See “To select a Home City by conﬁguring latitude and longitude settings” (page
E-20).

E-4

E-5

Contents
E-3

About This Manual

E-4

Things to check before using the watch

E-11 Mode Reference Guide
E-16 Timekeeping
E-17 Conﬁguring Home City Settings
E-17 To conﬁgure Home City settings
E-19 To change the Daylight Saving Time (summer time) setting
E-20 Conﬁguring Latitude and Longitude Settings for Your Current Location
E-20 To select a Home City by conﬁguring latitude and longitude settings
E-22 Conﬁguring Current Time and Date Settings
E-22 To change the current time and date settings

E-26 Hand Home Position Adjustment
E-26 To adjust home positions
E-29 Taking Direction Readings
E-30 To take a direction reading
E-36 To perform bidirectional calibration
E-38 To perform magnetic declination correction
E-43 Thermometer
E-43 To enter and exit the Thermometer Mode
E-45 To correct the temperature value
E-47 Specifying Temperature Unit
E-47 To specify the temperature unit
E-49 Looking up Sunrise and Sunset Times
E-49 To look up the sunrise and sunset times on a speciﬁc date
E-50 To toggle between sunrise time and sunset time
E-51 To view the sunrise/sunset time for a particular date

E-6

E-52 Using Moon Data
E-52 To look up the Moon age on a speciﬁc date
E-54 Using the Alarm
E-54 To enter the Alarm Mode
E-55 To set an alarm time
E-56 To test the alarm
E-57 To turn an alarm and the Hourly Time Signal on and off
E-57 To stop the alarm
E-58 Using the Stopwatch
E-58 To enter the Stopwatch Mode
E-58 To perform an elapsed time operation
E-58 To pause at a split time

E-7

E-60 Using the Countdown Timer
E-60 To enter the Countdown Timer Mode
E-60 To specify the countdown start time
E-61 To perform a countdown timer operation
E-62 To stop the alarm
E-63 Checking the Current Time in a Different Time Zone
E-63 To enter the World Time Mode
E-64 To view the time in another time zone
E-64 To specify standard time or daylight saving time (DST) for a city
E-65 Illumination
E-65 To turn on illumination
E-66 To change the illumination duration
E-68 Button Operation Tone
E-68 To turn the button operation tone on and off

E-8

E-9

Operation Guide 5269
Mode Reference Guide

E-70 Troubleshooting
E-75 Speciﬁcations

Your watch has 9 “modes”. The mode you should select depends on what you want to do.
To do this:
• View the current time and date in the Home City
• Conﬁgure Home City and daylight saving time (DST) settings
• Conﬁgure current location latitude and longitude settings
• Conﬁgure time and date settings
• Determine your current bearing or the direction from your current
location to a destination as a direction indicator and angle value
• Determine your current location using the watch and a map
Determine the temperature at your current location
View the sunrise and sunset times for a speciﬁc date
Determine a Moon age value
Set an alarm time
Use the stopwatch to measure elapsed time
Use the countdown timer
View the current time in one of 48 cities (31 time zones) around the globe

Enter this mode:

See:

Timekeeping Mode

E-16

Digital Compass
Mode

E-29

Thermometer Mode
Sunrise/Sunset Mode
Moon Age Mode
Alarm Mode
Stopwatch Mode
Countdown Timer Mode
World Time Mode

E-43
E-49
E-52
E-54
E-58
E-60
E-63
E-11

E-10

Selecting a Mode
• The illustration below shows which buttons you need to press to navigate between
modes.
• To return to the Timekeeping Mode from any other mode, hold down C for about
two seconds.
• In any mode, press L to illuminate the display.
Alarm Mode

Timekeeping Mode

Sunrise/Sunset Mode

Digital Compass Mode

Moon Age Mode

World Time Mode
Stopwatch Mode

Thermometer Mode

Countdown Timer Mode

E-13

E-12

General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Auto Return Features
• If you do not perform any operation for a certain amount of time in certain modes as
shown in the table below, the watch will automatically return to the Timekeeping
Mode.
Mode

No operation time

Digital Compass, Thermometer

1 to 2 minutes

Sunrise/Sunset, Moon Age, Alarm

2 to 3 minutes

Initial Screens
When you enter the Sunrise/Sunset Mode, Digital Compass Mode, Alarm Mode, or
World Time Mode, the data you were viewing when you last exited the mode will
appear ﬁrst.
Scrolling
The B and D buttons are used on the setting screen to scroll through available
settings on the digital display. In most cases, holding down these buttons during a
scroll operation scrolls through the data at high speed.

• If you leave a setting screen (one with ﬂashing digits) on the digital display for two
or three minutes without performing any operation, the watch exits the setting
screen automatically.

E-14

E-15

Timekeeping

Conﬁguring Home City Settings

Use the Timekeeping Mode to set and view the current time and date.
• Each press of A in the Timekeeping Mode toggles the digital display between the
current date and the current time.
• You can select one of the two following Date Screen display formats: SUN 6.30 or
SUN 30.6. For information about how to select the format, see “Date Display
Format” under “To change the current time and date settings” (page E-22).

There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).

Date screen
Month Day

Day of week

Regular timekeeping screen
Hour : Minutes Seconds

To conﬁgure Home City settings
1. In the Timekeeping Mode, hold down A for at least two
City Name
seconds until ADJUST appears on the digital display.
This is the setting mode. Release A after ADJUST
appears.
• The city name of the currently selected Home City
data will appear on the digital display with an arrow
( ) ﬂashing to the left.
• The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
• For details about city data, see the “City Data Table”
at the back of this manual.

E-16

E-17

2. Press D (East) and B (West) to scroll through city names until the one you want
to use as your Home City data is displayed.
3. Press C to display the DST setting screen.
4. Press D to toggle between Daylight Saving Time (DST ON) and Standard Time
(DST OFF).

Setting
DST indicator

E-18

5. When the setting is the way you want, press A twice to
return to the Timekeeping Mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
Note
• After you specify city data, the watch will use UTC*
offsets to calculate the current time for other time
zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide
scientiﬁc standard of timekeeping.
The reference point for UTC is Greenwich, England.

To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A for at least two
seconds until ADJUST appears on the digital display.
Release A after ADJUST appears.
• The name of the city currently selected as your
Home City will appear on the digital display with an
arrow ( ) ﬂashing to the left.
Setting
DST indicator

2. Press C to display the DST setting screen.
3. Press D to toggle between Daylight Saving Time
(DST ON) and Standard Time (DST OFF).
4. When the setting is the way you want, press A twice to
return to the Timekeeping Mode.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.

E-19

Operation Guide 5269
Conﬁguring Latitude and Longitude Settings for Your Current Location
You can ensure correct display of sunrise and sunset time settings, and of moon ages
by conﬁguring latitude and longitude settings for your current location.
To select a Home City by conﬁguring latitude and longitude settings
1. In the Timekeeping Mode, hold down A for at least two
seconds until ADJUST appears on the digital display.
This is the setting mode. Release A after ADJUST
appears.
• Your current Home City data will appear on the
digital display with an arrow ( ) ﬂashing to the left.
2. Press A to display the latitude setting screen with the
current latitude setting ﬂashing.

3. Use D (+) and B (–) to change the ﬂashing value in 0.1° increments.
• Holding down D or B while the latitude or longitude setting screen is
displayed will scroll the value to the left of the decimal point (the value to the
right does not change) at high speed.
S 62.0°

S 61.9°

S 0.1°

N 0°

N 0.1°

N 61.9°

N 62.0°

4. When the latitude is the value you want, press C to display the longitude setting
screen with the current longitude setting ﬂashing.
5. Use D (+) and B (–) to change the ﬂashing value in 0.1° increments.
W 179.9°

W 179.8°

W 0.1°

E 0°

E 0.1°

E 179.9°

E 180°

6. When the settings are the way you want, press A to return to the Timekeeping
Mode.
E-20

E-21

Conﬁguring Current Time and Date Settings
You can use the procedure below to adjust the current time and date settings if they
are not correct.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-26).
To change the current time and date settings
1. In the Timekeeping Mode, hold down A for at least two
seconds until ADJUST appears on the digital display.
This is the setting mode. Release A after ADJUST
appears.
• The name of the city currently selected as your Home
City will appear on the digital display with an arrow
( ) ﬂashing to the left.

2. Use D and B to select the city data you want.
• Select your Home City data before changing any other setting.
• For full information on city data, see the “City Data Table” at the back of this
manual.
3. Press C to move the ﬂashing in the sequence shown below to select the other settings.
City data

DST

Date Display Format

12/24-Hour Format

Illumination Duration

Seconds

Hour

Button Operation Tone On/Off

Minute

Day

Year

Month

• The following steps explain how to conﬁgure timekeeping settings only.
4. When the timekeeping setting you want to change is ﬂashing, use B and/or D to
change it as described below.

City name

E-22

E-23

Screen

To do this:

Do this:

Change the city name

Use D (East) and
B (West).

Toggle between Daylight Saving Time
(DST ON) and Standard Time (DST OFF).

Press D.

Toggle between 12-hour (12H) and 24-hour
(24H) timekeeping.

Press D.

Reset the seconds to 00
Change the hour or minute

Note
• For information about selecting a Home City and conﬁguring the DST setting, see
“Conﬁguring Home City Settings” (page E-17).
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• Changing your Home City setting will initialize the latitude and longitude settings to
the location of the Home City.

Press D.

Change the year, month, or day

Use D (+) and
B (–).

Select the date display format (DMY, YMD,
MDY)

Press D.

5. When the settings are the way you want, press A twice to return to the
Timekeeping Mode.
E-24

E-25

Hand Home Position Adjustment

Hour and minute hands

The hour, minute, and second hands of this watch can be put out of position by strong
magnetism or strong impact. When this happens, you can use the procedure below to
adjust the hand positions.
To adjust home positions
Second hand

1. In the Timekeeping Mode, hold down A for at least
four seconds until HAND SET appears on the digital
display. This is the setting mode. Release A after
HAND SET appears.
• This will cause SEC 00 to ﬂash on the digital
display, indicating the second hand adjustment
mode.

2. Check the position of the second hand.
• If the second hand is pointing to 12 o’clock, it is in
the correct home position. If it isn’t, use D (forward)
and B (back) to adjust the second hand position
so it points to 12 o’clock.
• Holding down either button will cause the second
hand to move at high speed.
3. Press C. This will cause 0:00 to ﬂash on the digital
display, indicating the hour and minute adjustment
mode.

Correct hour and
minute hand positions

4. Check the positions of the hour and minute hands.
• The hands are in the correct home positions if they
are pointing to 12 o’clock. If they aren’t, use D
(forward) and B (back) to adjust their positions.
• Holding down either button will cause the hour and
minute hands to move at high speed.

E-26

5. Press A to exit the setting screen.
• This will cause the hour and minute hands to move to the current Timekeeping
Mode time.

E-28

E-27

Taking Direction Readings
The watch has a magnetic sensor that makes it possible to take digital compass
readings. You can use the digital compass to ﬁnd the direction to a speciﬁc objective
and to determine your current position.
• See “Magnetic North and True North” (page E-40) for information about the two
types of north. For information about maximizing digital compass accuracy, see
“Calibrating Direction Readings” (page E-34) and “Digital Compass Precautions”
(page E-40).

E-29

Operation Guide 5269
To take a direction reading
12 o’clock position
1. Point the 12 o’clock position of the watch in the
direction you want to read.
North pointer

Direction
indicator

NNW N0
NW
E
N
N

Angle value
(in degrees)

ENE E

WSW W

270

SSE S

E-30

ES
E

180

2. In the Timekeeping Mode or Thermometer Mode, keep
the watch horizontal as you press B.
• COMPASS will appear on the digital display and
then direction reading will start.
• After the watch completes a reading, the second
hand will indicate north. The direction indicator
will show a literal indicator (abbreviation) for the
direction where 12 o’clock of the watch is pointed. A
direction angle will also be displayed.
Starting a digital compass direction reading causes
consecutive readings to be taken each second for
20 seconds. After a series of consecutive readings
is complete, - - - appears in place of the literal
direction indicator on the display.
• See “Digital Compass Readings” (page E-31) for
information about what appears on the digital display.

North indicated
on the map

Example: Determining your current position and your
objective on a map
Having an idea of your current location and the direction
to your destination is important when mountain climbing or
hiking. In this example, we show you how to plot directions
on a map and determine your current location using
direction measurements taken by the watch.

1. In the Timekeeping Mode or Thermometer Mode, press
B.

3. Press C to return to the Timekeeping Mode.
• If you do not perform any button operation for one or two minutes, the watch
will automatically return to the Timekeeping Mode.

Digital Compass Readings
• The following table shows the meanings of each of the direction abbreviations that appear
on the digital display.
Direction

Meaning

Direction

Meaning

Direction

Meaning

Direction

Meaning

North

NNE

Northnortheast

Northeast

ENE

Eastnortheast

East

ESE

Eastsoutheast

Southeast

SSE

Southsoutheast

South

SSW

Southsouthwest

Southwest

WSW

Westsouthwest

WNW

Westnorthwest

Northwest

NNW

Northnorthwest

West

E-31

2. Rotate the map (without moving the watch) until north on the map is aligned with
north as indicated by the watch’s second hand.
Depending on how the watch is set up, it may be indicating magnetic north or true
north.
Magnetic north: Indicates north in accordance with the Earth’s magnetic ﬁeld.
True north: Indicates the direction to the North Pole.
• For information about setting the watch up to indicate magnetic north or true
north, see “Magnetic Declination Correction” (page E-37).
3. Determine your location and destination by checking the map and the geographic
contours around you.

North indicated by
north pointer
E-33

E-32

Calibrating Direction Readings
You can use the information in this section to calibrate direction readings, which helps
to improve digital compass accuracy.

Direction Reading Calibration Methods
Important!
• To ensure correct direction readings by this watch, be sure to perform bidirectional
calibration before using it. The watch may produce incorrect direction readings if
you do not perform bidirectional calibration.
• Keep the watch away from audio speakers, magnetic necklace, cell phone, and
other devices that generate strong magnetism. Exposure to strong magnetism can
magnetize the watch and cause incorrect direction readings. If incorrect readings
continue even after you perform bidirectional calibration, it could mean that your
watch has been magnetized. If this happens, contact your original retailer or an
authorized CASIO Service Center.

Bidirectional Calibration
• Use this method when using the watch to take readings in an area where magnetic
force is present, or if you notice that the readings produced by the watch are
different from another compass.
Magnetic Declination Calibration
• You can use this method to specify a magnetic declination value, which sets the
digital compass up to take magnetic north or true north readings.
Precautions about bidirectional calibration
• You can use any two opposing directions for bidirectional calibration. You must,
however, make sure that they are 180 degrees opposite each other. Remember
that if you perform the procedure incorrectly, you will get wrong bearing sensor
readings.
• Do not move the watch while calibration of either direction is in progress.
• You should perform bidirectional calibration in an environment that is the same as
that where you plan to be taking direction readings. If you plan to take direction
readings in an open ﬁeld, for example, calibrate in an open ﬁeld.

E-34

E-35

To perform bidirectional calibration
1. In the Digital Compass Mode, hold down A for two
seconds.
• This will cause the bidirectional calibration screen to
appear on the digital display.
• The second hand will move to 12 o’clock. This
causes an arrow ( ) symbol to ﬂash on the left
side of the digital display and -1- to be displayed to
indicate that the watch is ready for calibration of the
ﬁrst direction.
2. Place the watch on a level surface facing any direction
you want, and press B to calibrate the ﬁrst direction.
• - - - will remain on the digital display while
calibration is in progress. OK will appear when
ﬁrst direction calibration is complete. About one
second after that, the ﬂashing arrow will change to
point downwards ( ) and -2- will be displayed. This
means that the watch is ready for calibration of the
second direction.

3. Rotate the watch 180 degrees.
4. Press B again to calibrate the second direction.
• - - - will remain on the digital display while
calibration is in progress. OK will appear when
second direction calibration is complete.
• If ERR appears on the digital display, press B
again to restart calibration.

• Magnetic Declination Correction
With magnetic declination correction, you input a magnetic declination angle
(difference between magnetic north and true north), which allows the watch to
indicate true north. You can perform this procedure when the magnetic declination
angle is indicated on the map you are using. Note that you can input the declination
angle in whole degree units only, so you may need to round off the value speciﬁed on
the map. If your map indicates the declination angle as 7.4°, you should input 7°. In
the case of 7.6° input 8°, for 7.5° you can input 7° or 8°.

E-36

E-37

To perform magnetic declination correction
1. In the Digital Compass Mode, hold down A for two
Magnetic declination
seconds.
angle direction value
(E, W, or OFF)
• This will cause the bidirectional calibration screen
to appear on the digital display.
2. Press C to display the magnetic declination setting
screen (DEC).

• You can select a value within the range of W 90° to E 90° with these settings.
• You can turn off (OFF) magnetic declination correction by pressing D and B
at the same time.
• The illustration, for example, shows the value you should input and the direction
setting you should select when the map shows a magnetic declination of 7°
West.
4. When the setting is the way you want, press A to exit the setting screen.

3. Use D (East) and B (West) to change the settings.
• The following explains magnetic declination angle
direction settings.
OFF: No magnetic declination correction performed.
The northerly magnetic declination setting
(DEC) will be 0°.
E:
When magnetic north is to the east (east
Magnetic declination
declination)
angle value
W: When magnetic north is to the west (west
declination)
E-38

E-39

Operation Guide 5269
Digital Compass Precautions
Magnetic North and True North
The northerly direction can be expressed either as
True north
magnetic north or true north, which are different from each
other. Also, it is important to keep in mind that magnetic
Magnetic north
north moves over time.
• Magnetic north is the north that is indicated by the
needle of a compass.
• True north, which is the location of the North Pole of the
Earth’s axis, is the north that is normally indicated on
Earth
maps.
• The difference between magnetic north and true north
is called the “declination”. The closer you get to the
North Pole, the greater the declination angle.

Location
• Taking a direction reading when you are near a source of strong magnetism can
cause large errors in readings. Because of this, you should avoid taking direction
readings while in the vicinity of the following types of objects: permanent magnets
(magnetic necklaces, etc.), concentrations of metal (metal doors, lockers, etc.),
high tension wires, aerial wires, household appliances (TVs, personal computers,
washing machines, freezers, etc.).
• Accurate direction readings are impossible while in a train, boat, air plane, etc.
• Accurate readings are also impossible indoors, especially inside ferroconcrete
structures. This is because the metal framework of such structures picks up
magnetism from appliances, etc.

E-40

Storage
• The precision of the bearing sensor may deteriorate if the watch becomes
magnetized. Because of this, you should store the watch away from magnets or any
other sources of strong magnetism, including: permanent magnets (magnetic
necklaces, etc.) and household appliances (TVs, personal computers, washing
machines, freezers, etc.).
• Whenever you suspect that the watch may have become magnetized, perform the
procedure under “To perform bidirectional calibration” (page E-36).

E-41

Thermometer
This watch uses a temperature sensor to take temperature readings.
To enter and exit the Thermometer Mode
1. In the Timekeeping Mode or Digital Compass Mode,
press D.
• THERMO will appear on the digital display for about
one second indicating that temperature readings
are being taken. After that, the measurement result
will appear.
• The watch will take temperature readings every ﬁ ve
seconds for one or two minutes.
• To restart temperature readings, press D.
Temperature

E-42

Temperature
• Temperature is displayed in units of 0.1°C (or 0.2°F).
• The displayed temperature value changes to --.- °C (or °F) if a measured
temperature falls outside the range of –10.0°C to 60.0°C (14.0°F to 140.0°F). The
temperature value will reappear as soon as the measured temperature is within the
allowable range.

2. Press C to return to the Timekeeping Mode.
• If you do not perform any button operation for one
or two minutes after temperature measurement is
complete, the watch will automatically return to the
Timekeeping Mode.

E-43

Important!
• Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following before doing anything.
– Compare the readings produced by the watch with those of another reliable and
accurate thermometer.
– If adjustment is required, remove the watch from your wrist and wait for 20 or 30
minutes to give the temperature of the watch time to stabilize.

Display Units
You can select either Celsius (°C) or Fahrenheit (°F) for the displayed temperature
value. See “To specify temperature unit” (page E-47) for more information.

Temperature Sensor Calibration
The watch’s temperature sensor is calibrated at the factory and normally requires no
further adjustment. If you notice serious errors in the temperature readings produced
by the watch, you can calibrate the sensor to correct the errors.

To correct the temperature value
You can correct the temperature readings displayed by
the watch in accordance with another measuring
instrument for more accurate readings.
1. In the Thermometer Mode, hold down A until the
current temperature value ﬂashes on the digital display.
This is the setting screen.

E-44

2. Use D (+) and B (–) to calibrate the temperature value with the reading of another
instrument.
• Each press of a button changes the temperature value in units of 0.1°C (0.2°F).
• To return the currently ﬂashing value to its initial factory default setting, press
B and D at the same time. OFF will appear at the ﬂashing location for about
one second, followed by the initial default value.
3. Press A to return to the Thermometer Mode.
Thermometer Precautions
• Temperature measurements are affected by your body temperature (while you are
wearing the watch), direct sunlight, and moisture. To achieve a more accurate
temperature measurement, remove the watch from your wrist, place it in a well
ventilated location out of direct sunlight, and wipe all moisture from the case. It
takes approximately 20 to 30 minutes for the case of the watch to reach the actual
surrounding temperature.
• When taking temperature readings, it is best to remove the watch from your wrist in
order to eliminate the effects of body heat. Remove the watch from your wrist and
allow it to hang freely from your bag or in another location where it is not exposed
to direct sunlight.

E-45

Specifying Temperature Unit
Use the procedure below to specify the temperature unit to be used in the
Thermometer Mode.
Important!
When TOKYO is selected as the Home City, the
temperature unit is set automatically to Celsius (°C).
These settings cannot be changed.
To specify the temperature unit
1. Enter the Thermometer Mode and then hold down A for
about two seconds until the current temperature value
ﬂashes on the digital display. This is the setting screen.
2. Press C to display the temperature unit setting screen
with either °C or °F (the current setting) ﬂashing.

E-46

3. Press D to toggle the temperature unit between °C (Celsius) and °F (Fahrenheit).
4. After the setting is the way you want, press A to exit the setting screen.

E-47

Looking up Sunrise and Sunset Times
You can use the Sunrise/Sunset Mode to look up the sunrise and sunset times for a
particular date (year, month, day) and location.
To look up the sunrise and sunset times on a speciﬁc date
Use C to select the Sunrise/Sunset Mode as shown on
page E-13.
• SUNRISE TIME or SUNSET TIME will appear on the
)
(or
digital display for about one second. After that the
current year, month, and day will appear for about one
second.
• Next, CALC will appear to indicate that calculation is in
progress. After the calculation is complete, the sunrise
time or sunset time for the current date will appear.
• What appears ﬁrst when the enter the Sunrise/Sunset
Mode (either the sunrise time or sunset time) will be the
Sunrise time or
time that was displayed when you last exited the
sunset time
Sunrise/Sunset Mode.

E-48

E-49

Operation Guide 5269
Note
• Sunrise and sunset times are calculated in accordance with the current date based
on the currently speciﬁed Home City, latitude, and longitude.
• Before trying to use the Sunrise/Sunset Mode, you need to conﬁgure settings for the
Home City, longitude, and latitude for the location whose sunrise and sunset times
you want to view.
To toggle between sunrise time and sunset time
Press A.

To view the sunrise/sunset time for a particular date
While the sunrise time or sunset time is displayed in the
Sunrise/Sunset Mode, use B (+) and D (–) to scroll
through the dates.
• The sunrise time or sunset time for the currently
selected date will appear on the digital display.
• You can select any date between January 1, 2000 and
December 31, 2099.
Sunrise time or
sunset time

Note
• If you think that the sunrise and/or sunset times
are not correct for some reason, check the watch’s
Home City, longitude and latitude settings.
• The sunrise and sunset times displayed by this
watch are times at sea level. Sunrise and sunset
times are different at altitudes other than sea level.

E-50

E-51

Using Moon Data
The Moon Age Mode displays a value that indicates the Moon age at noon on the
current date.
To look up the Moon age on a speciﬁc date
1. Use C to select the Moon Age Mode (MOON AGE) as
Moon age
shown on page E-12.
• MOON AGE will appear on the digital display for
about one second. After that the current year, month,
and day will appear for about one second.
• Next, CALC will appear on the digital display
indicating that Moon age calculation is in progress.
After the calculation is complete, the Moon age value
for the current date will appear.

2. While a Moon age value is displayed you can use the D (+) and B (–) buttons to
scroll from day to day.
• Scrolling to another day will cause CALC to appear on the digital display for one
second indicating that Moon age calculation is in progress. The Moon age for
the selected data will appear when calculation is complete.
• Hold down C for two seconds to return to the Timekeeping Mode.
Note
• Moon age is calculated to an accuracy of ±1 day.
• If the Moon data is not correct, check your Timekeeping Mode settings and correct
them if necessary.

E-52

E-53

Using the Alarm
Alarm
number

Alarm time
(Hour : Minutes) or SIG
Alternates
(1 second)

You can set ﬁve independent daily alarms. When a daily
alarm is turned on, an alarm tone will sound for about 10
seconds each day when the time in the Timekeeping
Mode reaches the preset alarm time. This is true even if
the watch is not in the Timekeeping Mode.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.

• The alarm number indicates an alarm screen. SIG is shown when the Hourly Time
Signal screen is on the digital display.
• When you enter the Alarm Mode, the data you were viewing when you last exited
the mode appears ﬁrst.
To set an alarm time
1. In the Alarm Mode, use D and B to scroll through the
alarm screens until the one whose time you want to set
is displayed.

To enter the Alarm Mode
Use C to select the Alarm Mode (ALARM) as shown on
page E-12.
• ALARM will appear on the digital display for about one
second. After that, the digital display will show the
current alarm time and alarm number (–1 to –5), or the
hourly time signal setting. In the case of an alarm, the
digital display alternates at one-second intervals
between the alarm number and the on/off setting screen.

−1

−2

−3

SIG

−5

−4

2. Hold down A until the alarm time starts to ﬂash. This is
the setting screen.

E-54

E-55

3. Press C to move the ﬂashing between the hour and minute settings.
4. While a setting is ﬂashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. or p.m.

To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use D and B to select an alarm or
the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want is
selected, press A to toggle it between on and off.

5. Press A to exit the setting screen.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.

Hourly time signal
on indicator

• The alarm on indicator (when any alarm is on) and the
Hourly Time Signal on indicator (when the Hourly
Time Signal is on) are shown on the digital display
in all modes.

Alarm on indicator

To stop the alarm
Press any button.

E-56

E-57

Using the Stopwatch

• Digital display alternates between SPL and the 1/100-second value at one-second
intervals.

The stopwatch measures elapsed time and split times.
To enter the Stopwatch Mode
Use C to select the Stopwatch Mode (STW) as shown on
Seconds
Hours
page E-12.
• STW will appear on the digital display for about one
second. Next, the digital display will change to show
the stopwatch time.
To perform an elapsed time operation

Minutes
1/100 second

E-58

Start

Stop

(Restart)

(Stop)

Reset

Note
• The Stopwatch Mode can indicate elapsed time up to 23 hours, 59 minutes, 59.99
seconds.
• Once started, stopwatch timing continues until you press B to reset it, even if you
exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch
limit deﬁned above.
• Exiting the Stopwatch Mode while a split time is frozen on the digital display clears
the split time and returns to elapsed time measurement.

To pause at a split time
D

Start

Split

Split release Stop

Reset
E-59

Operation Guide 5269
Using the Countdown Timer
The countdown timer can be conﬁgured to start at a preset time and sound an alarm
when the end of the countdown is reached.
To enter the Countdown Timer Mode
Use C to select the Countdown Timer Mode (TIMER) as
shown on page E-12.
• TIMER will appear on the digital display for about one
second. Next, the digital display will change to show
the countdown time.

• If a countdown is paused, press B to reset to the current countdown start
time.
2. Hold down A until the minute setting of the current countdown start time starts to
ﬂash. This is the setting screen.
3. Press C to move the ﬂashing between the minute and second settings.
4. Use D (+) and B (–) to change the ﬂashing item.
• To set the starting value of the countdown time to 100 minutes, set 00'00".
5. Press A to exit the setting screen.
To perform a countdown timer operation

Countdown time
(Minutes, seconds)

To specify the countdown start time
1. Enter the Countdown Timer Mode.
• If a countdown is in progress (indicated by the
seconds counting down), press D to stop it and
then press B to reset to the current countdown
start time.

Start

Stop

(Restart)

(Stop)

Reset

• Before starting a countdown timer operation, check to make sure that a countdown
operation is not already in progress (indicated by the seconds counting down). If it
is, press D to stop it and then B to reset to the countdown start time.

E-60

E-61

• An alarm sounds for ten seconds when the end of the countdown is reached. This
alarm will sound in all modes. The countdown time is reset to its starting value
automatically after the alarm sounds.
To stop the alarm
Press any button.

Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 31 time zones (48
cities) around the globe. The city that is currently selected in the World Time Mode is
called the “World Time City”.
Currently
selected
World
Time City

To enter the World Time Mode
Use C to select the World Time Mode (WORLD TIME)
as shown on page E-13.
• WORLD TIME will appear on the digital display for
about one second. Next, the name of the currently
selected World Time city will scroll across the digital
display. Finally, the current time in the World Time city
will appear.
• To display the World Time city name again, press A.

Current time in the
currently selected
World Time City
E-62

E-63

To view the time in another time zone
In the World Time Mode, use B (East) and D (West) to scroll through World Time
cities and view the current time in displayed city.
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use B (East) and D (West) to
display the world time city (time zone) whose Standard
Time/Daylight Saving Time setting you want to change.

DST indicator

2. Hold down A for at least two seconds to toggle
between Daylight Saving Time (DST ON) and Standard
Time (DST OFF).
• Changing the DST setting of your Home City in the
World Time Mode will also change the DST setting
of the Timekeeping Mode time.

Illumination
The display of the watch is illuminated for easy reading in
the dark.
To turn on illumination
In any mode (except when a setting screen is on the
digital display), press L to illuminate the display.
• You can use the procedure below to select either 1.5
seconds or three seconds as the illumination duration.
When you press L, the display will remain illuminated
for about 1.5 seconds or three seconds, depending on
the current illumination duration setting.

• Note that you cannot switch between standard time/daylight saving time
(DST) while UTC is selected as the World Time City.
• Note that the standard time/daylight saving time (DST) setting affects only the
currently selected time zone. Other time zones are not affected.
E-64

To change the illumination duration
1. In the Timekeeping Mode, hold down A for at least two seconds until ADJUST
appears on the digital display. This is the setting mode. Release A after ADJUST
appears.
• The name of the city currently selected as your Home City will appear on the
digital display with an arrow ( ) ﬂashing to the left.
2. Press C 10 times until LIGHT 1 or LIGHT 3 is displayed.
• See step 3 under “To change the current time and date settings” (page E-22)
for information about how to scroll through setting screens.

E-65

Illumination Precautions
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Illumination will not turn on while an alarm is sounding, while high-speed hand
movement is in progress, while a sensor is taking a reading, or while the watch is
performing calculation (CALC displayed). Illumination will turn on if L is pressed
between sensor reading operations.
• Frequent use of illumination runs down the battery.

3. Press D to toggle the illumination duration between three seconds (LIGHT 3
displayed) and 1.5 seconds (LIGHT 1 displayed).
4. When the setting is the way you want, press A twice to return to the Timekeeping
Mode.

E-66

Button Operation Tone
The button operation tone sounds any time you press one of the watch’s buttons. You
can turn the button operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, and
Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A for at least two
seconds until ADJUST appears on the digital display.
This is the setting mode. Release A after ADJUST
appears.
• The name of the city currently selected as your
Home City will appear on the digital display with an
arrow ( ) ﬂashing to the left.

E-68

E-67

2. Use C to cycle through settings on the digital display until the current button
operation tone setting (MUTE or KEY ) is displayed.
• See step 3 under “To change the current time and date settings” (page E-22)
for information about how to scroll through setting screens.
3. Press D to toggle the button operation tone between on (KEY ) and off (MUTE).
4. When the setting is the way you want, press A twice to return to the Timekeeping
Mode.

E-69

Operation Guide 5269
Troubleshooting
Time Setting
■ Why is the current time setting off by a couple of hours?
Your Home City setting may be wrong (page E-17). Check your Home City setting and
correct it, if necessary.

■ Why does “ERR” appear while a sensor operation is in progress?
Subjecting the watch to strong impact can cause sensor malfunction or improper
contact of internal circuitry. When this happens, ERR (error) will appear on the digital
display and sensor operations will be disabled.
Direction Reading and
Temperature Measurement

■ Why is the current time setting off by one hour?
You may need to change your Home City’s standard time/daylight saving time (DST)
setting. Use the procedure under “To change the current time and date settings” (page
E-22) to change the standard time/daylight saving time (DST) setting.
Sensor modes
■ Why can’t I change the temperature unit setting?
The temperature unit setting is always Celsius (°C) whenever TOKYO is selected as
the Home City. In this case, the setting cannot be changed.

• If ERR appears while a measurement operation is being performed in a sensor
mode, restart the measurement. If ERR appears on the digital display again, it can
mean there is something wrong with the sensor.
• If ERR keeps appearing during measurement, it can mean there is a problem with
the applicable sensor.

E-70

E-71

■ Why does “ERR” appear on the digital display following bidirectional
calibration?
If - - - appears and then changes to ERR (error) on the calibration screen, it means
that there is something wrong with the sensor.
• If ERR disappears after about one second, try performing the calibration again.
• If ERR keeps appearing, contact your original dealer or nearest authorized CASIO
distributor to have the watch checked.
Whenever you have a sensor malfunction, take the watch to your original dealer or
nearest authorized CASIO distributor as soon as possible.

■ What causes different direction readings to produce different results at the
same location?
Magnetism generated by nearby high-tension wires is interfering with detection of
terrestrial magnetism. Move away from the high-tension wires and try again.
■ Why am I having problems taking direction readings indoors?
A TV, personal computer, speakers, or some other object is interfering with terrestrial
magnetism readings. Move away from the object causing the interference or take the
direction reading outdoors. Indoor direction readings are particularly difﬁcult inside
ferro-concrete structures. Remember that you will not be able to take direction
readings inside of trains, airplanes, etc.

■ What causes incorrect direction readings?
• Incorrect bidirectional calibration. Perform bidirectional calibration (page E-36).
• Nearby source of strong magnetism, such as a household appliance, a large steel
bridge, a steel beam, overhead wires, etc., or an attempt to perform direction
measurement on a train, boat, etc. Move away from large metal objects and try
again.
E-72

E-73

Battery
■ Why is the low battery alert ﬂashing?
Battery power is low. Watch operations are disabled while
the low battery alert is ﬂashing on the digital display.
If the low battery alert disappears after battery power
recovers but then starts to ﬂash again after a short while,
it means that you need to have the watch’s battery
replaced.
Low battery alert

Speciﬁcations
Accuracy at normal temperature: ±30 seconds a month
Digital Timekeeping: Hour, minutes, seconds, a.m. (A)/p.m. (P), month, day, day of
the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City (can be assigned one of 48 city codes); Standard Time / Daylight
Saving Time (summer time)
Analog Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds
Digital Compass: North indicated by second hand; 20 seconds continuous readings;
Calibration (bidirectional); Magnetic declination correction; Magnetic north
indication; display of one of 16 direction indicators; Angle value 0° to 359°
Thermometer:
Measurement and display range: –10.0 to 60.0°C (or 14.0 to 140.0°F)
Display unit: 0.1°C (or 0.2°F)
Reading timing: 5-second intervals for 1 to 2 minutes

E-74

E-75

Bearing Sensor Precision:
Direction: Within ±15°
Values are guaranteed for a temperature range of –10°C to 40°C (14°F to 104°F).
Temperature Sensor Precision:
±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)
Moon Age: Display of Moon age values for speciﬁc dates
Sunrise/Sunset: Sunrise time and sunset time for speciﬁc date
Alarms: 5 daily alarms; hourly time signal
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59 59.99
Measuring modes: Elapsed time, split time
Countdown Timer:
Measuring unit: 1 second
Countdown start time setting range: 1 second to 100 minutes (1-minute
increments and 1-second increments)

World Time: 48 cities (31 time zones)
Other: Daylight Saving Time/Standard Time
Illumination: LED (Light-emitting diode); Selectable illumination duration
(approximately 1.5 seconds or 3 seconds)
Other: Button operation tone on/off
Battery: Two silver oxide batteries (Type: SR927W)
Approximate battery operating time: 2 years under the following conditions:
• 1 illumination operation (1.5 seconds) per day
• 20 seconds of continuous direction readings, 20 times per month
• 2 minutes of continuous temperature readings (5-second intervals), once per
week
• 20 seconds of alarm operation per day
Frequent use of illumination runs down the battery.

E-76

E-77

City Code Table

UTC Offset/
GMT Differential

City Name

Latitude (°)
North Latitude +,
South Latitude –

Longitude (°)
East Longitude +,
West Longitude –
35.2

UTC Offset/
GMT Differential

City Name

Latitude (°)
North Latitude +,
South Latitude –

Longitude (°)
East Longitude +,
West Longitude –

2.0

Jerusalem

31.8

3.0

Moscow

55.8

37.6

0.0

UTC

51.5

3.0

Jeddah

21.5

39.2

0.0

Lisbon

38.7

–9.1

3.5

Tehran

35.7

51.4

0.0

London

51.5

–0.1

4.0

Dubai

25.3

55.3

1.0

Madrid

40.4

–3.7

4.5

Kabul

34.5

69.2

1.0

Paris

48.9

2.4

5.0

Karachi

24.9

67.0

1.0

Rome

41.9

12.5

5.5

Delhi

28.6

77.2

1.0

Berlin

52.5

13.4

5.75

Kathmandu

27.7

85.3

1.0

Stockholm

59.3

18.1

6.0

Dhaka

23.7

90.4

2.0

Athens

38.0

23.7

6.5

Yangon

16.8

96.2

2.0

Cairo

30.0

31.2

7.0

Bangkok

13.7

100.5

L-1

Operation Guide 5269
UTC Offset/
GMT Differential

City Name

Latitude (°)
North Latitude +,
South Latitude –

Longitude (°)
East Longitude +,
West Longitude –

UTC Offset/
GMT Differential

City Name

Latitude (°)
North Latitude +,
South Latitude –

Longitude (°)
East Longitude +,
West Longitude –

8.0

Singapore

1.3

103.8

8.0

Hong Kong

22.4

114.1

–10.0

Honolulu

21.3

–157.9

–9.0

Anchorage

61.2

8.0

Beijing

39.9

–149.9

116.4

–8.0

Vancouver

49.3

8.0

Taipei

–123.1

25.1

121.6

–8.0

Los Angeles

34.1

9.0

–118.2

Seoul

37.6

127.0

–7.0

Edmonton

53.5

–113.5

9.0

Tokyo

35.7

139.7

–7.0

Denver

39.7

–105.0

9.5

Adelaide

–34.9

138.6

–6.0

Mexico City

19.4

–99.1

10.0

Guam

13.4

144.8

–6.0

Chicago

41.9

–87.6

10.0

Sydney

–33.9

151.2

–5.0

New York

40.7

–74.0

11.0

Noumea

–22.3

166.5

–4.0

Santiago

–33.4

–70.6

12.0

Wellington

–41.3

174.8

–4.0

Halifax

44.6

–63.6

–11.0

Pago Pago

–14.3

–170.7

–3.5

St.Johns

47.6

–52.7

L-2

L-3

UTC Offset/
GMT Differential

City Name

Latitude (°)
North Latitude +,
South Latitude –

–3.0

Rio De Janeiro

–2.0

Fernando de Noronha –3.8

–32.4

–1.0

Praia

–23.5

–22.9
14.9

Longitude (°)
East Longitude +,
West Longitude –
–43.2

• UTC Offset/GMT Differential: Based on data for June 2012
• The rules governing global times (GMT differential and UTC offset) and summer
time are determined by each individual country.

L-4

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Author                          : CASIO COMPUTER CO., LTD.
Create Date                     : 2012:08:02 11:33:22+09:00
Keywords                        : PDF, Manual
Modify Date                     : 2014:12:07 12:56:15+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Metadata Date                   : 2014:12:07 12:56:15+08:00
Creator Tool                    : Adobe Acrobat 7.0
Document ID                     : uuid:3AD674684ADCE111A965E6F8E0432E4A
Instance ID                     : uuid:0ee64a32-6189-b34b-92a3-c472db44b637
Derived From Instance ID        : uuid:5fcc767e-c8d4-4654-b7e2-e7e3731b1aa7
Derived From Document ID        : uuid:94f01c27-9c75-4e34-9ada-cd405c25d082
Format                          : application/postscript
Title                           : QW-5269
Creator                         : CASIO COMPUTER CO., LTD.
Page Layout                     : OneColumn
Page Count                      : 9

EXIF Metadata provided by EXIF.tools

Casio 5269 Operation Manual QW

Navigation menu

Versions of this User Manual:

Views

Navigation