Casio Aqs800W 1B2V Wrist Watch Aqs800W1B2V Users Manual QW 5208
AQS800W1B2V to the manual 18dfdd95-b622-4615-aad2-5616ddfdf785
2015-01-21
: Casio Casio-Casio-Aqs800W-1B2V-Wrist-Watch-Aqs800W1B2V-Users-Manual-243924 casio-casio-aqs800w-1b2v-wrist-watch-aqs800w1b2v-users-manual-243924 casio pdf
Open the PDF directly: View PDF
Page Count: 6
![Operation Guide 5208MO1106-EAE-1Getting AcquaintedCongratulations upon your selection of this CASIO watch. To get the most out of yourpurchase, be sure to read this manual carefully.Keep the watch exposed to bright lightThe electricity generated by the solar cell of the watch isstored by a built-in battery. Leaving or using the watchwhere it is not exposed to light causes the battery to rundown. Make sure the watch is exposed to light as much aspossible.•When you are not wearing the watch on your wrist,position the face so it is pointed at a source of brightlight.•You should try to keep the watch outside of your sleeveas much as possible. Charging is reduced significantly ifthe face is only partially covered.lllllllllllBright LightSolar cellE-2Battery charges in the light. Battery discharges in the dark.AllfunctionsenabledLEVEL 1LEVEL 2LEVEL 3LEVEL 4ChargeRechargeable batteryBright LightElectrical energySolar cell(Converts light to electrical power.)LEVEL 1LEVEL 2LEVEL 3LEVEL 4Some or allfunctionsdisabledDis-charge•The watch continues to operate, even when it is not exposed to light. Leaving thewatch in the dark can cause the battery to run down, which will result in some watchfunctions being disabled. If the battery goes dead, you will have to re-configurewatch settings after recharging. To ensure normal watch operation, be sure to keep itexposed to light as much as possible.E-3•The actual level at which some functions are disabled depends on the watch model.•Be sure to read “Power Supply” (page E-33) for important information youneed to know when exposing the watch to bright light.If the display of the watch is blank...If the display of the watch is blank, it means that the watch’s Power Saving functionhas turned off the display to conserve power.•See “Power Saving Function” (page E-46) for more information.E-4About This Manual•Depending on the model of your watch, display textappears either as dark figures on a light background, orlight figures on a dark background. All sample displaysin this manual are shown using dark figures on a lightbackground.•Button operations are indicated using the letters shownin the illustration.•Each section of this manual provides you with theinformation you need to perform operations in eachmode. Further details and technical information can befound in the “Reference” section.E-5ContentsGeneral Guide ......................................................................................................... E-8Timekeeping .......................................................................................................... E-10World Time ............................................................................................................. E-17Alarms .................................................................................................................... E-20Countdown Timer .................................................................................................. E-24Stopwatch .............................................................................................................. E-29Illumination ............................................................................................................ E-31Power Supply ........................................................................................................ E-33Adjusting Home Positions ................................................................................... E-42Reference .............................................................................................................. E-44Specifications ....................................................................................................... E-50E-6Procedure LookupThe following is a handy reference list of all the operational procedures contained inthis manual.To set the current digital time and date .............................................................. E-11To change the Daylight Saving Time (summer time) setting ............................ E-15To view the time in another city ........................................................................... E-18To toggle a city code time between Standard Timeand Daylight Saving Time ............................................................................... E-18To swap your Home City and World Time City ................................................... E-19To set an alarm time ............................................................................................. E-21To turn an alarm on and off .................................................................................. E-23To turn the Hourly Time Signal on and off .......................................................... E-23E-7To configure the countdown timer ...................................................................... E-25To use the countdown timer ................................................................................ E-27To measure times with the stopwatch ................................................................ E-30To illuminate the display ...................................................................................... E-31To specify the illumination duration ................................................................... E-32To check the current battery level ....................................................................... E-35To adjust home positions ..................................................................................... E-42To turn the button operation tone on and off ..................................................... E-45To recover from the sleep state ........................................................................... E-47E-8Timekeeping ModeC▲General Guide•Press C to change from mode to mode.•In any mode (except when a setting screen is on the display), press B to illuminatethe face of the watch.Battery Level IndicatorC▲E-9Stopwatch Mode Countdown Timer ModeAlarm Mode▲World Time ModeCC▲▲C C▲](https://usermanual.wiki/Casio/CasioCasioAqs800W1B2VWristWatchAqs800W1B2VUsersManual243924.1116237483-User-Guide-Page-1.png)
![Operation Guide 5208E-10•All of the operations in this section are performed in the Timekeeping Mode, whichyou can enter by pressing C (page E-8).TimekeepingUse the Timekeeping Mode to set and view the current time and date.•When setting the time, you can also configure settings for the 12/24-hour format.•Each press of D cycles the digital display in the sequence shown below.DDay Day of weekDD▲▲PM indicatorHour : MinuteSecondSecond SecondMonth▲E-11City codeSetting the Digital Time and DateMake sure you select your Home City code before you change the current time anddate settings. World Time Mode times are all displayed in accordance with theTimekeeping Mode settings. Because of this, World Time Mode times will not becorrect if you do not select the proper Home City code before setting the time anddate in the Timekeeping Mode.To set the current digital time and date1. In the Timekeeping Mode, hold down A for about twoseconds, until “ADJ” appears on the display.•Your current Home City code will be flashing on thescreen.2. Press C to move the flashing in the sequence shownbelow to select other settings.E-123. While the setting you want to change is flashing, use D and B to change it asexplained below.Screen: To do this:Change the city codeToggle between Daylight Saving Time(ON) and Standard Time (OFF).Toggle between 12-hour (12H) and24-hour (24H) timekeepingReset the seconds to 00Do this:Press D (east) and B (west).Press D.Press D.Press D.City CodeLanguage IlluminationDuration Day Month Ye a rDST 12/24-HourFormat Seconds Hour MinutesButton OperationTo n eE-13To do this:Change the hour or minutesChange the yearChange the month or dayToggle the button operation tonebetween (on) and (off)Toggle the illumination duration betweenLT1 (approximately 1.5 seconds) andLT3 (approximately 3 seconds).Change the day of the week languageENG: English POR: PortugueseESP: Spanish FRA: FrenchDEU: German ITA : ItalianScreen: Do this:Use D (+) and B (–).Press D.Press D.Use D (+) and B (–).•See “City Code Table” at the back of this manual for a complete list of availablecity codes.E-144. Press A to exit the setting screen.•The day of the week is automatically displayed in accordance with the date (year,month, and day) settings.12-hour and 24-hour timekeeping•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits fortimes in the range of noon to 11:59 p.m. and no indicator appears for times in therange of midnight to 11:59 a.m.•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, withoutany indicator.•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode isapplied in all other modes.Daylight Saving Time (DST)Daylight Saving Time (summer time) advances the time setting by one hour fromStandard Time. Remember that not all countries or even local areas use DaylightSaving Time.E-15To change the Daylight Saving Time (summer time) setting1. In the Timekeeping Mode, hold down A for about two seconds, until “ADJ” appearson the display.•Your current Home City code will be flashing on the screen.2. Press C once to display the DST setting screen.3. Press D to toggle between Daylight Saving Time (ON displayed) and StandardTime (OFF displayed).4. When the setting you want is selected, press A to exit the setting screen.•The DST indicator appears on the display to indicate that Daylight Saving Time isturned on.E-16Analog TimekeepingThe analog time of this watch is synchronized with the digital time. The analog timesetting is adjusted automatically whenever you change the digital time.Note•The hands for the analog timepiece move to adjust to a new setting whenever any ofthe following occurs.When you change the digital time settingWhen you change the Home City code and/or DST setting•If the analog time does not match the digital time for any reason, use the proceduredescribed under “To adjust home positions” (page E-42) to match the analog settingto the digital setting.•Whenever you need to adjust both the digital and the analog time settings, makesure you adjust the digital setting first.•Depending on how much the hands have to move in order to synchronize to thedigital time, it may take some time before they stop moving.E-17World TimeThe World Time Mode digitally displays the current time in48 cities (31 time zones) around the world.•If the current time shown for a city is wrong, check yourHome City time settings and make the necessarychanges (page E-11).•After you press C to enter the World Time Mode, yourcurrently selected World Time City code will appear onthe digital display for about two seconds. After that, thecurrent time in that city will appear.•All of the operations in this section are performed in theWorld Time Mode, which you enter by pressing C(page E-9).City codeCurrent time inselected cityE-18To view the time in another cityIf you press D while in the World Time Mode, your currently selected World Time Citycode will appear on the digital display for about two seconds. After that, the currenttime in that city will appear. Pressing D again while the World Time City code isdisplayed will scroll to the next city code.•For full information on city codes, see the “City Code Table” at the back of thismanual.To toggle a city code time between Standard Time and Daylight Saving Time1. In the World Time Mode, use D to display the city code(time zone) whose Standard Time/Daylight Saving Timesetting you want to change.2. Hold down A to toggle Daylight Saving Time (DSTindicator displayed) and Standard Time (DST indicatornot displayed).• The DST indicator will appear on the display wheneveryou display a city code for which Daylight Saving Time isturned on.DST indicatorE-19• Note that the DST/Standard Time setting affects only the currently displayed citycode. Other city codes are not affected.Swapping your Home City and World Time CityYou can use the procedure below to swap your Home City and World Time City. Thischanges your Home City to your World Time City, and your World Time City to yourHome City. This capability can come in handy when you frequently travel between twocities in different time zones.To swap your Home City and World Time City1. In the World Time Mode, use D to select the World Time City you want.2. Hold down A and B until the watch beeps.• This will make the World Time City you selected in step 1 your Home City, and causethe hour and minute hands to move to the current time in that city. At the same time,it will change the Home City you had selected prior to step 2 your World Time City.• After swapping the Home City and World Time City, the watch stays in the WorldTime Mode with the city that was selected as the Home City prior to step 2 nowdisplayed as the World Time City.](https://usermanual.wiki/Casio/CasioCasioAqs800W1B2VWristWatchAqs800W1B2VUsersManual243924.1116237483-User-Guide-Page-2.png)