Casio Clock 2323 Users Manual QW 2322/2323

2323 to the manual a1689e17-1dc5-488c-95b7-fa273b3bd4c3

2015-01-21

: Casio Casio-Casio-Clock-2323-Users-Manual-242919 casio-casio-clock-2323-users-manual-242919 casio pdf

Open the PDF directly: View PDF PDF.
Page Count: 2

DownloadCasio Casio-Casio-Clock-2323-Users-Manual- QW-2322/2323  Casio-casio-clock-2323-users-manual
Open PDF In BrowserView PDF
Module No.2322/2323

2322/2323-1

GENERAL GUIDE
• Press A to change from mode to mode.
The operational procedures for Module 2322 and 2323 are identical. All of the
illustrations in this manual show Module 2322.
Timekeeping Mode

[Module 2323]

Calendar Mode

Alarm Mode

Stopwatch Mode

Dual Time Mode

[Module 2322]

ABOUT THE BACKLIGHT

ALARM MODE

• Press L to illuminate the display for about 2 seconds.
• The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This does not indicate
malfunction of the watch.
• The illumination provided by the backlight may be hard to see when viewed under direct
sunlight.
• The backlight automatically turns off whenever an alarm sounds.
• When the backlight is turned on, it blinks whenever the minute hand moves. This is normal,
and does not indicate malfunction of the watch.

When the Daily Alarm is turned on, an alarm sounds for 20 seconds at the preset time each
day. When the Hourly Time Signal is switched on, the watch beeps every hour on the hour.

To set the alarm time and to turn the Daily Alarm and Hourly Time Signal on and off
Alarm on indicator
Hourly Time Signal on indicator
Hold down
C.

Press C .

TIMEKEEPING MODE

To set the time and date
Hour hand Minute hand

Press C.

Seconds

Press C.

Hour

12/24
Press C.

Press
C.

Left
minutes
digit

Right
minutes
digit

Alarm/Hourly
Time
Signal
on/off
setting
Alarm/Hourly
Time
Signal
setting

Press C.

Hour Minutes

• Use this mode to set the current time. An incorrect digital time setting will result in incorrect
operation of the calendar.

Hold down C.

Press
C.

Hour

1. Hold down C until the hour digits start to flash.
2. Press A to increase the hour digits. Holding down A changes the digits at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select for normal
timekeeping.
3. Press C to move the selection to the left minutes digit.
4. Press A to increase the left minutes digit. Holding down A changes the digit at high speed.
5. Press C to move the selection to the right minutes digit.
6. Press A to increase the right minutes digit. Holding down A changes the digit at high speed.
7. Press C to move Daily Alarm and Hourly Time Signal on and off setting.
8. Press A to change the status of the Daily Alarm and Hourly Time Signal in the following
sequence.
• At this time Daily Alarm and Hourly Time Signal automatically turn on.

Minutes
Press C.

Hour Seconds
Minutes
PM indicator

Both ON

1. Hold down C until the seconds digits start to flash.
2. Press A to reset the seconds to 00. If you press A while the seconds count is in the range
of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds count
is in the range of 00 to 29, the minutes count is unchanged.
3. Press C to move the selection to the hour digits.
4. Press A to increase the hour digits. Holding down A changes the hour digits at high speed.
5. Press C to move the selection to the minutes digits.
6. Press A to increase the minutes digits. Holding down A changes the minutes digits at high
speed.
7. Press C to move the selection to 12/24.
8. Press A to toggle the timekeeping format between 12-hour and 24-hour.
• When 12-hour format is selected, the indicator P appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.
9. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Timekeeping Mode automatically.

Daily Alarm
Alarm
Only
only

Hourly
Hourly Time
Time
Signal
Signal Only
only

9. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Alarm Mode automatically.

To stop the alarm

• Press any button to stop the alarm after it starts to sound.

To test the alarm and select an alarm tone
Hold down A in any mode (except when making any settings) to sound the alarm.
Each time you test the alarm, a four different alarm tones. The alarm tone you select is used for
the Daily Alarm and Hourly Time Signal.
• Note that holding down A also changes the mode.

To set the hands
When in any Mode, press B with a thin object to advance the analog time setting. Each press
of B advances the time by 20 seconds. Three presses advance by one minute.
Holding down B advances the analog setting at high speed. You can only advance the setting
and cannot reverse it.

Both OFF
Both

DUAL TIME MODE
To semt the Dual Time

Hold down C.

CALENDAR MODE

Press C.

Hour

Minutes

Press C .

12/24
Press C .

To set the date
Hour
Seconds
Minutes
PM indicator
Hold down C.

Press C .

Month

Day

Press C.

Day of week
Press C.

Month

Day of week
Day

1. Hold down C until the month digits start to flash.
2. Press A to increase the month digits. Holding down A changes the digits at high speed.
3. Press C to move the selection to day digits.
4. Press A to increase the day digits. Holding down A changes the digits at high speed.
5. Press C to move the selection to the day of the week indication.
6. Press A to advance to the next day. Holding down A changes the indication at high speed.
7. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Calendar Mode automatically.

1. Hold down C until the hour digits start to flash.
2. Press A to increase the hour digits. Holding down A changes the digits at high speed.
3. Press C to move the selection to the minutes digits.
4. Press A to increase the minutes digits. Holding down A changes the digits at high speed.
5. Press C to move the selection to 12/24.
6. Press A to toggle the timekeeping format between 12-hour and 24-hour.
• When 12-hour format is selected, the indicator P appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.
7. Press C to complete the procedure.
• If you do not operate any button for a few minutes while a selection is flashing, the flashing
stops and the watch goes back to the Dual Time Mode automatically.
• In the Dual Time Mode, the seconds count is synchronized with the seconds count of the
Timekeeping Mode.

2322/2323-2
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time. The range of
the stopwatch is 59 minutes 59.99 seconds.

To use the Stopwatch

Minutes
1/100 second
Seconds

1. Press C to start the stopwatch.
2. Press C to stop the time measurement.
• You can press C as many times as you want to resume and stop
timing.
3. After you are finished using the stopwatch, hold down C to clear
the stopwatch time to all zeros.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2000:04:20 13:26:47
Producer                        : Acrobat Distiller 3.01 for Power Macintosh
Author                          : MAS
Creator                         : PageMaker 6.5
Title                           : QW-2322/2323
Keywords                        : WAT
Modify Date                     : 2000:06:15 14:17:53+09:00
Page Count                      : 2
Page Mode                       : UseThumbs
Page Layout                     : OneColumn
EXIF Metadata provided by EXIF.tools

Navigation menu