Casio G Shock Solar Atomic Watch Gw69001V Users Manual QW 3179

MO0905-EA qw3179

GW69001V to the manual d57f8b5c-6872-4429-ab2c-88067f66eb66

2015-01-21

: Casio Casio-Casio-G-Shock-Solar-Atomic-Watch-Gw69001V-Users-Manual-243943 casio-casio-g-shock-solar-atomic-watch-gw69001v-users-manual-243943 casio pdf

Open the PDF directly: View PDF .
Page Count: 6

Getting Acquainted
General Guide
Radio-controlled Atomic Timekeeping
World Time
Alarms
Stopwatch
Countdown Timer
Illumination
Power Supply
Timekeeping
Reference
Specifications
City Code Table

Operation Guide 3179

MO0905-EA

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your

purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the watch is

stored by a rechargeable battery. Leaving or using the

watch where it is not exposed to light causes the battery

to run down. Make sure the watch is exposed to light as

much as possible.

•When you are not wearing the watch on your wrist,

position the face so it is pointed at a source of bright

light.

•You should try to keep the watch outside of your sleeve

as much as possible. Charging is reduced significantly if

the face is covered only partially.

Bright Light

Solar cell

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

•The watch continues to operate, even when it is not exposed to light. Leaving the

watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch

settings after recharging. To ensure normal watch operation, be sure to keep it

exposed to light as much as possible.

•The actual level at which some functions are disabled depends on the watch model.

•Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a

single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a window

Approximately about 8 hours exposure to indoor fluorescent lighting

•Be sure to read “Power Supply” for important information you need to know

when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving function

has turned off the display to conserve power.

•See “Power Saving Function” for more information.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage

or loss suffered by you or any third party arising through the use of this product or

its malfunction.

About This Manual

•Depending on the model of your watch, display text appears either as dark figures

on a light background or light figures on a dark background. All sample displays in

this manual are shown using dark figures on a light background.

•Button operations are indicated using the letters shown in the illustration.

•Each section of this manual provides you with the information you need to perform

operations in each mode. Further details and technical information can be found in

the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press L to illuminate

the display.

Timekeeping Mode

Press C.

Countdown Timer Mode Stopwatch Mode

Alarm Mode

▲

World Time Mode

▲

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly.

•This watch is designed to pick up the time calibration signals transmitted in Germany

(Mainflingen), England (Anthorn), the United States (Fort Collins), China (Shangqiu),

and Japan (Fukushima, Fukuoka/Saga).

Current Time Setting

This watch adjusts its time setting automatically in accordance with a time calibration

signal. You also can perform a manual procedure to set the time and date, when

necessary.

•The first thing you should do after purchasing this watch is to specify your

Home City (the city where you normally will use the watch). For more

information, see “To specify your Home City” below.

•When using the watch outside the areas covered by the time signal transmitters, you

will have to adjust the current time setting manually as required. See “Timekeeping”

for more information about manual time settings.

•The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of

Canada, the continental United States, and Mexico.

To specify your Home City

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press D (east) and B (west) to select the city code

you want to use as your Home City.

LIS, LON : Lisbon, London

MAD, PAR, ROM, BER, STO : Madrid, Paris,

Rome, Berlin, Stockholm

ATH : Athens

MOW : Moscow

HKG, BJS, TPE : Hong Kong, Beijing, Taipei

SEL, TYO : Seoul, Tokyo

HNL : Honolulu

ANC : Anchorage

City code

PM indicator

Seconds

Hour : Minutes

YVR, LAX : Vancouver, Los Angeles

YEA, DEN: Edmonton, Denver

MEX, CHI : Mexico City, Chicago

NYC : New York

YHZ : Halifax

YYT : St.Johns

3. Press A to exit the setting screen.

•Normally, your watch should show the correct time as soon as you select your Home

City code. If it does not, it should adjust automatically after the next auto receive

operation (in the middle of the night). You also can perform manual receive or you

can set the time manually.

•The watch will receive the time calibration signal automatically from the applicable

transmitter (in the middle of the night) and update its settings accordingly. For

information about the relationship between city codes and transmitters, see

“Important!” under “Time Calibration Signal Reception” and “Transmitters”.

•See the maps under “Approximate Reception Ranges” for information about the

reception ranges of the watch.

•You can disable time signal reception, if you want. See “To turn auto receive on and

off” for more information.

•Under factory default settings, auto receive is turned off for all of the following city

codes: MOW (Moscow), HNL (Honolulu), and ANC (Anchorage). For details about

turning on auto receive for these city codes, see “To turn auto receive on and off”.

Time Calibration Signal Reception

There are two different methods you can use to receive the time calibration signal:

auto receive and manual receive.

•Auto Receive

With auto receive, the watch receives the time calibration signal automatically up to

6 times a day (5 times a day for the Chinese calibration signal). When any auto

receive is successful, the remaining auto receive operations are not performed. For

more information, see “About Auto Receive”.

•Manual Receive

Manual receive lets you start a time calibration receive operation with the press of a

button. For more information, see “To perform manual receive”.

Important!

•When getting ready to receive the time calibration signal, position the watch as

shown in the nearby illustration, with its 12 o’clock side pointing towards a window.

This watch is designed to receive a time calibration signal late at night. Because of

this, you should place the watch near a window as shown in the illustration when you

take it off at night. Make sure there are no metal objects nearby.

12 o’clock

•Make sure the watch is facing the right way.

•Proper signal reception can be difficult or even impossible under the conditions listed

below.

Inside or

among

buildings

Inside a

vehicle

Near a

construction

site, airport,

or other

sources of

electrical

noise

Near high-

tension power

lines

Near

household

appliances,

office

equipment,

or a mobile

phone

Among or

behind

mountains

Operation Guide 3179

•Signal reception normally is better at night than during the day.

•Time calibration signal reception takes from two to seven minutes, but in some

cases it can take as long as 14 minutes. Take care that you do not perform any

button operations or move the watch during this time.

•The time calibration signal the watch will attempt to pick up depends on its current

Home City code setting as shown below.

Home City Code

LIS, LON, MAD, PAR, ROM,

BER, STO, ATH, MOW*

HKG, BJS

TPE, SEL, TYO

HNL*, ANC*, YVR, LAX, YEA,

DEN, MEX, CHI, NYC, YHZ, YYT

Frequency

60.0 kHz

77.5 kHz

68.5 kHz

40.0 kHz

60.0 kHz

Transmitter

Anthorn (England)

Mainflingen (Germany)

Shangqiu City (China)

Fukushima (Japan)

Fukuoka/Saga (Japan)

Fort Collins, Colorado

(the United States)

* The areas covered by the HNL, ANC, and MOW city codes are quite far from the

time calibration signal transmitters, and so certain conditions may cause problems

with signal reception.

•Calibration signal reception is disabled while a countdown timer operation is in

progress.

Approximate Reception Ranges

U.K. and German Signals

Anthorn

Mainflingen

1,500 kilometers

500 kilometers

The Anthorn signal

is receivable within

this area.

U.S. Signal

Fort Collins

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Signals are receivable in the Taiwan area when reception conditions are good.

Shangqiu

1,000 kilometers

Fukuoka/Saga

500 kilometers

Fukushima

500 kilometers

Changchun

Beijing

1,500 kilometers

Shanghai

Chengdu

Japan Signals

China Signal

Hong Kong

•Signal reception may not be possible at the distances noted below during certain

times of the year or day. Radio interference also may cause problems with reception.

Mainflingen (Germany) or Anthorn (England) transmitters: 500 kilometers

(310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 1,500 kilometers (910 miles)

•Even when the watch is within the reception range of the transmitter, signal

reception will be impossible if the signal is blocked by mountains or other geological

formations between the watch and signal source.

•Signal reception is affected by weather, atmospheric conditions, and seasonal

changes.

•See the information under “Signal Reception Troubleshooting” if you experience

problems with time calibration signal reception.

About Auto Receive

The watch receives the time calibration signal automatically up to 6 times a day

(5 times a day for the Chinese calibration signal). When any auto receive is

successful, the remaining auto receive operations are not performed. The reception

schedule (calibration times) depends on your currently selected Home City, and

whether standard time or Daylight Saving Time is selected for your Home City.

2:00 am

3:00 am

4:00 am

5:00 am

Midnight*

3:00 am

4:00 am

5:00 am

Midnight*

1:00 am*

4:00 am

5:00 am

Midnight*

1:00 am*

2:00 am*

5:00 am

Midnight*

1:00 am*

2:00 am*

3:00 am*

Standard Time

Daylight Saving Time

Standard Time

Daylight Saving Time

Standard Time

Daylight Saving Time

Standard Time

Daylight Saving Time

1:00 am

2:00 am

3:00 am

4:00 am

5:00 am

Midnight*

1:00 am*

2:00 am*

3:00 am*

4:00 am*

LIS

LON

MAD

PAR

ROM

BER

STO

ATH

MOW

Your Home City Auto Receive Start Times

12 3456

*Next day

HKG

BJS

TPE

SEL

TYO

HNL

ANC

YVR

LAX

YEA

DEN

MEX

CHI

NYC

YHZ

YYT

Standard Time and

Daylight Saving Time

Standard Time

Standard Time and

Daylight Saving Time

1:00 am

Midnight

2:00 am

1:00 am

3:00 am

2:00 am

4:00 am

3:00 am

5:00 am

4:00 am

5:00 am

Note

•When a calibration time is reached, the watch will receive the calibration signal only

if it is in either the Timekeeping Mode or World Time Mode. Reception is not

performed if a calibration time is reached while you are configuring settings.

•Auto receive of the calibration signal is designed to be performed early in the

morning, while you sleep (provided that the Timekeeping Mode time is set correctly).

Before going to bed for the night, remove the watch from your wrist, and put it in a

location where it can receive the signal easily.

•The watch receives the calibration signal for two to seven minutes everyday when

the time in the Timekeeping Mode reaches a calibration time. Do not perform any

button operation within seven minutes before or after the calibration times. Doing so

can interfere with correct calibration.

•Remember that reception of the calibration signal depends on the current time in the

Timekeeping Mode. The receive operation will be performed whenever the display

shows any one of the calibration times, regardless of whether or not the displayed

time actually is the correct time.

About the Signal Strength Indicator

The signal strength indicator shows the strength of the calibration signal being

received. For best reception, be sure to keep the watch in a location where signal

strength is strongest. The signal strength indicator is displayed while an auto or

manual receive operation is in progress.

RCVD indicator

Signal strength indicator

Strong

(Level 3)

Weak

(Level 1)

•Even in an area where signal strength is strong, it takes about 10 seconds for signal

reception to stabilize enough for the signal strength indicator to indicate signal

strength.

•Use the signal strength indicator as a guide for checking signal strength and for

finding the best location for the watch during signal receive operations.

•Following reception of the time calibration signal and calibration of the watch’s time

setting, the RCVD indicator will remain on the display in all modes. The RCVD

indicator will not be displayed if signal reception was unsuccessful or after you adjust

the current time setting manually.

•The RCVD indicator is displayed only when the watch is able to receive both time

and date data successfully. It does not appear when only time data is received.

•The RCVD indicator indicates that at least one of the auto calibration signal receive

operations was successful. Note, however, that the RCVD indicator disappears from

the display each day when the first auto receive operation of the day is performed.

To perform manual receive

1. Enter the Timekeeping Mode.

2. Hold down D for about two seconds until RCVD starts

to flash on the display. This indicates that manual

receive is in progress.

•Time calibration signal reception takes from two to

seven minutes. Take care that you do not perform

any button operations or move the watch during this

time.

•If the receive operation is successful, the reception

date and time appear on the display, along with the

GET indicator.

3. After manual receive is complete, press D to return to

normal timekeeping.

•The watch also will return to normal timekeeping if you

do not perform any button operation for about one or

two minutes.

Receiving

Receive successful

•If the latest reception fails but a previous reception was

successful, an indicator (RCVD) will be on the display.

•The watch will return to normal timekeeping without

changing the time setting if you press D or if you do not

perform any button operation for about one or two

minutes.

Note

•To interrupt a receive operation and return to normal

timekeeping, press D.

If there was a previously

successful reception

If no reception was

successful

Receive failed

To turn auto receive on and off

1. In the Timekeeping Mode, press D to display the last

successful receive time and date screen.

2. Hold down A until the current auto receive setting (ON

or OFF) starts to flash. This is the setting screen.

•Note that the setting screen will not appear if the

currently selected Home City is one that does not

support time calibration reception.

3. Press D to toggle auto receive on (ON) and off

(OFF).

4. Press A to exit the setting screen.

•For information about city codes that support signal

receive, see “To specify your Home City”.

On/Off status

To check the latest signal reception results

Press D to view the last successful receive time and

date. Press D again to return to the previous screen.

Operation Guide 3179

•The watch is not in the

Timekeeping Mode.

•Your current Home City is not one

of the following: LIS, LON, MAD,

PAR , ROM, BER, STO, ATH,

MOW, HKG, BJS, TPE, SEL, TYO,

HNL, ANC, YVR, LAX, YEA, DEN,

MEX, CHI, NYC, YHZ, or YYT

•You changed the time setting

manually.

•The DST setting was changed

manually in the World Time Mode.

•You pressed a button while signal

receive was in progress.

•Even if receive is successful, the

RCVD indicator will disappear

from the display each day when

the first auto receive operation of

the day is performed.

•Time data (hour, minutes, seconds)

only was received during the last

receive operation. The RCVD

indicator appears only when time

data and date data (year, month,

day) are both received.

Cannot perform

manual receive.

Auto receive is

turned on, but

the RCVD

indicator does

not appear on

the display.

•Enter the Timekeeping

Mode and try again.

•Select LIS, LON, MAD,

PAR, ROM, BER, STO,

ATH, MOW, HKG, BJS,

TPE, SEL, TYO, HNL, ANC,

YVR, LAX, YEA, DEN,

MEX, CHI, NYC, YHZ,

or YYT as your Home City.

•Perform manual signal

receive or wait until the next

auto signal receive

operation is performed.

•Check to make sure the

watch is in a location where

it can receive the signal.

What you should doProblem Probable Cause

Signal Reception Troubleshooting

Check the following points whenever you experience problems with signal reception.

•For further information, see “Important!” under “Time Calibration Signal Reception”

and “Radio-controlled Atomic Timekeeping Precautions”.

•If the time is one hour off, the DST

setting may be incorrect.

•The Home City code setting is not

correct for the area where you are

using the watch.

•Change the DST setting to

Auto DST.

•Select the correct Home

City code.

Time setting

is incorrect

following

signal

reception.

World Time

World Time shows the current time in 48 cities (31 time

zones) around the world.

•The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an error in

any World Time Mode time, check to make sure you

have the correct city selected as your Home City. Also

check to make sure that the current time as shown in

the Timekeeping Mode is correct.

•Select a city code in the World Time Mode to display the

current time in any particular time zone around the

globe. See the “City Code Table” for information about

the UTC differential settings that are supported.

Current time in

selected city

City code

•All of the operations in this section are performed in the World Time Mode, which

you enter by pressing C.

To view the time in another city

While in the World Time Mode, use the D (eastward) and B (westward) to scroll

through the city codes (time zones).

•Pressing the D and B at the same time will jump to the UTC time zone.

To toggle a city code time between Standard Time and Daylight Saving Time

1. In the World Time Mode, use D and B to display the

city code (time zone) whose Standard Time/Daylight

Saving Time setting you want to change.

2. Hold down A to toggle between Daylight Saving Time

(DST indicator displayed) and Standard Time (DST

indicator not displayed).

•The DST indicator is shown on the World Time Mode

screen while Daylight Saving Time is turned on.

•Note that the Standard Time/Daylight Saving Time

setting affects only the currently displayed city code.

Other city codes are not affected.

•Note that you cannot switch between Standard Time

and Daylight Saving Time while UTC is selected as the

city code.

DST indicator

Alarms

The Alarm Mode gives you a choice of four one-time

alarms and one snooze alarm.

Also use the Alarm Mode to turn the Hourly Time Signal

(SIG) on and off.

•There are five alarm screens numbered AL1, AL2,

AL3 and AL4 for the one-time alarm, and a snooze

alarm screen indicated by SNZ. The Hourly Time

Signal screen is indicated by SIG.

•All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

Alarm number

Alarm time

(Hour : Minutes)

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

•To set a one-time alarm, display alarm screen AL1, AL2, AL3 or AL4.

To set the snooze alarm, display the SNZ screen.

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and B (–) to change it.

•With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off.

•Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the operations below during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the

SNZ

setting screen

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press B to toggle it on and off.

•Turning on a alarm (AL1, AL2, AL3, AL4 or

SNZ) displays the alarm on indicator on its Alarm Mode

screen.

•In all modes, the alarm on indicator is shown for any

alarm that currently is turned on.

•The alarm on indicator flashes while the alarm is

sounding.

•The snooze alarm indicator flashes while the snooze

alarm is sounding and during the 5-minute intervals

between alarms.

Alarm on indicator

Snooze alarm

indicator

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal (SIG).

2. Press B to toggle it on and off.

•The Hourly Time Signal on indicator is shown on the

display in all modes while this function is turned on.

Hourly time signal

on indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

•The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

•The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

•All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

1/100 second

Hours

Seconds

Minutes

To measure times with the stopwatch

Elapsed Time

Split Time

Two Finishes

Start

Stop Re-start Stop

Split

(SPL displayed)

Split release Stop

Split

First runner finishes.

Display time of first

runner.

Stop

Second runner

finishes.

Split release

Display time of

second runner.

➤➤➤

➤

Clear

Countdown Timer

You can set the countdown timer within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero.

•All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

Countdown End Beeper

The countdown end beeper lets you know when the

countdown reaches zero. The beeper stops after about 10

seconds or when you press any button.

Minutes

Seconds

Hours

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

•If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” to

display it.

2. Press C to move the flashing in the sequence shown

below to select other settings.

Hours Minutes

Operation Guide 3179

3. When the setting you want to change is flashing, use D and B to change it as

described below.

•To specify a countdown start time of 24 hours, set .

4. Press A to exit the setting screen.

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

•The countdown timer operation continues even if you

exit the Countdown Timer Mode.

•Press D while a countdown operation is in progress to

pause it. Press D again to resume the countdown.

•To stop a countdown operation completely, first pause it

(by pressing D), and then press B. This returns the

countdown time to its starting value.

Current timer

time Timer start time

Button Operation

Use D (+) and B (–) to change the setting.

Setting

Hours, Minutes

Screen

Illumination

This watch has an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch’s auto light switch turns on illumination

automatically when you angle the watch towards your face.

•The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

•See “Illumination Precautions” for other important

information about using illumination.

To illuminate the display manually

In any mode, press L to turn on illumination.

•The above operation turns on illumination regardless of

the current auto light switch setting.

Auto light switch on

indicator

•You can use the procedure below to select either 1.5 seconds or 3 seconds as the

illumination duration. When you press L, the illumination will remain on for about

1.5 seconds or 3 seconds, depending on the current illumination duration setting.

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the

display contents start to flash. This is the setting screen.

2. Press C 10 times until the current illumination duration

setting ( or ) appears.

3. Press D to toggle the setting between

(approximately 1.5 seconds) and (approximately

3 seconds).

4. Press A to exit the setting screen.

About the Auto Light Switch

Turning on the auto light switch causes illumination to turn on, whenever you position

your wrist as described below in any mode. Note that this watch features a “Full Auto

EL Light,” so the auto light switch operates only when available light is below a certain

level. It does not turn on the backlight under bright light.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes illumination to turn on.

• Wear the watch on the outside of your wrist.

Parallel to

ground More than 40°

Warning!

••

•Always make sure you are in a safe place whenever you are reading the

display of the watch using the auto light switch. Be especially careful when

running or engaged in any other activity that can result in accident or injury.

Also take care that sudden illumination by the auto light switch does not

startle or distract others around you.

••

•When you are wearing the watch, make sure that its auto light switch is turned

off before riding a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create a

distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down L for about three seconds to toggle the auto

light switch on (auto light switch on indicator displayed) and off (auto light switch on

indicator not displayed).

•The auto light switch on indicator is on the display in all modes while the auto light

switch is turned on.

Power Supply

This watch is equipped with a solar cell and a rechargeable battery that is charged by

the electrical power produced by the solar cell. The illustration shown below shows

how you should position the watch for charging.

Example: Orient the watch so its face is

pointing at a light source.

•The illustration shows how to position a

watch with a resin band.

•Note that charging efficiency drops when

any part of the solar cell is blocked by

clothing, etc.

•You should try to keep the watch outside of

your sleeve as much as possible. Charging

is reduced significantly if the face is

covered only partially.

Solar cell

•This watch uses a rechargeable battery to store power produced by the solar cell, so

regular battery replacement is not required. However, after very long use, the

rechargeable battery may lose its ability to achieve a full charge. If you experience

problems getting the rechargeable battery to charge fully, contact your dealer or

CASIO distributor about having it replaced.

•Never try to remove or replace the watch’s rechargeable battery yourself. Use of the

wrong type of battery can damage the watch.

•All data stored in memory is deleted, and the current time and all other settings

return to their initial factory defaults whenever battery power drops to Level 5 and

when you have the battery replaced.

•Turn on the watch’s Power Saving function and keep it in an area normally exposed

to bright light when storing it for long periods. This helps to keep the rechargeable

battery from going dead.

Level

Battery Power Indicator

(Charge Soon Alert)

Function Status

All functions enabled.

Auto and manual receive,

illumination, and beeper

disabled.

Except for timekeeping and

the CHG (charge) indicator,

all functions and display

indicators disabled.

All functions disabled.

Battery Power Indicator and Recover Indicator

The battery power indicator on the display shows you the current status of the

rechargeable battery’s power.

Battery power

indicator

•The flashing LOW indicator at Level 3 tells you that battery power is very low, and

that exposure to bright light for charging is required as soon as possible.

•At Level 5, all functions are disabled and settings return to their initial factory

defaults. Once the battery reaches Level 2 after falling to Level 5, reconfigure the

current time, date, and other settings.

•The watch’s Home City code setting will change automatically to TYO (Tokyo)

whenever the battery drops to Level 5. With this Home City code setting, the watch is

configured to receive the time calibration signals of Japan. If you are using the watch

in North America or Europe, or China you will need to change the Home City code

setting to match your location whenever the battery drops to Level 5.

•

Display indicators reappear as soon as the battery is charged from Level 5 to Level 2.

•Leaving the watch exposed to direct sunlight or some other very strong light source

can cause the battery power indicator to show a reading temporarily that is higher

than the actual battery level. The correct battery level should be indicated after a few

minutes.

•Performing illumination, or beeper operations during a

short period may cause (recover) to appear on the

display.

After some time, battery power will recover and

(recover) will disappear, indicating that the above

functions are enabled again.

•If (recover) appears frequently, it probably means

that remaining battery power is low. Leave the watch in

bright light to allow it to charge.

Recover indicator

Charging Precautions

Certain charging conditions can cause the watch to become very hot. Avoid leaving

the watch in the areas described below whenever charging its rechargeable battery.

Also note that allowing the watch to become very hot can cause its liquid crystal

display to black out. The appearance of the LCD should become normal again when

the watch returns to a lower temperature.

Warning!

Leaving the watch in bright light to charge its rechargeable battery can cause it

to become quite hot. Take care when handling the watch to avoid burn injury.

The watch can become particularly hot when exposed to the following

conditions for long periods.

•On the dashboard of a car parked in direct sunlight

•Too close to an incandescent lamp

•Under direct sunlight

Exposure Level (Brightness)

Outdoor Sunlight (50,000 lux)

Sunlight Through a Window (10,000 lux)

Daylight Through a Window on a Cloudy Day (5,000 lux)

Indoor Fluorescent Lighting (500 lux)

Approximate

Exposure Time

5 minutes

24 minutes

48 minutes

8 hours

Charging Guide

The following table shows the amount of time the watch needs to be exposed to light

each day in order to generate enough power for normal daily operations.

•For details about the battery operating time and daily operating conditions, see the

“Power Supply” section of the Specifications.

•Stable operation is promoted by frequent exposure to light.

Recovery Times

The table below shows the amount exposure that is required to take the battery from

one level to the next.

Approximate Exposure Time

Level 5 Level 4 Level 3 Level 2 Level 1

3 hours 18 hours 5 hours

9 hours 90 hours 24 hours

14 hours 182 hours 49 hours

155 hours - - - - - - - - - - - - - - - -

Exposure Level

(Brightness)

Outdoor Sunlight

(50,000 lux)

Sunlight Through a

Window (10,000 lux)

Daylight Through a

Window on a Cloudy

Day (5,000 lux)

Indoor Fluorescent

Lighting (500 lux)

▲

Important!

•Storing the watch for long periods in an area where there is no light or wearing it in

such a way that it is blocked from exposure to light can cause rechargeable battery

power to run down. Be sure that the watch is exposed to bright light whenever

possible.

•The above exposure time values are all for reference only. Actual required exposure

times depend on lighting conditions.

Operation Guide 3179

Timekeeping

Press the B button to toggle the lower display between

the day of the week and date, and the currently selected

World Time city and time (Dual Time).

Use the Timekeeping Mode to set and view the current

time and date.

Read This Before You Set the Time and Date!

This watch is preset with a number of city codes, each of

which represents the time zone where that city is located.

When setting the time, it is important that you first select

the correct city code for your Home City (the city where

you normally use the watch). If your location is not

included in the preset city codes, select the preset city

code that is in the same time zone as your location.

•Note that all of the times for the World Time Mode city

codes are displayed in accordance with the time and

date settings you configure in the Timekeeping Mode.

Current Time

PM indicator

Hour : Minutes

Seconds

Day of week

▲

Dual Time

▲

Dual timeCity code

Month – Day

To set the time and date manually

1. In the Timekeeping Mode hold down A until the city

code starts to flash, which indicates the setting screen.

2. Use D and B to select the city code you want.

•Make sure you select your Home City code before

changing any other setting.

•For full information on city codes, see the “City Code

Table”.

3. Press C to move the flashing in the sequence shown below to select the other

setting.

Seconds

12/24-Hour

Format Hour Minutes

DST

Month Year

City Code

DayPower Saving Illumination

Duration

Button

Operation Tone

•The following steps explain how to configure timekeeping settings only.

4. When the timekeeping setting you want to change is flashing, use D or B to

change it as described below.

Change the city code

Cycle between Auto DST (AvtA), Daylight

Saving Time (ON) and Standard Time

(OFF).

Toggle between 12-hour ( ) and 24-

hour ( ) timekeeping

Reset the seconds to

Change the hour and minutes

Use D (east) and B

(west).

Press D.

Use D (+) and B (–).

Screen: To do this: Do this:

5. Press A to exit the setting screen.

•Auto DST (AvtA) can be selected only while LIS, LON, MAD, PAR, ROM, BER,

STO, ATH, MOW,TPE, SEL, TYO, HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI,

NYC, YHZ, or YYT is selected as the Home City code. For more information, see

“Daylight Saving Time (DST)” below.

•The day of the week is displayed automatically in accordance with the date (year,

month, and day) settings.

Change the year, month, or day

Toggle the button operation tone between

(on) and (off)

Toggle the illumination duration between

(approximately 1.5 seconds) and

(approximately 3 seconds).

Toggle between Power Saving on ( ) and

off ( )

Use D (+) and B (–).

Press D.

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without

any indicator.

•The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is

applied in all other modes.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

The time calibration signals transmitted from Mainflingen (Germany), Anthorn

(England), or Fort Collins (the United States) include both Standard Time and DST

data. When the Auto DST setting is turned on, the watch switches between Standard

Time and DST (summer time) automatically in accordance with the signals.

•Though the time calibration signal transmitted by the Fukushima and Fukuoka/Saga,

Japan transmitters include summer time data, summer time currently is not

implemented in Japan (as of 2008).

•The default DST setting is Auto DST (AvtA) whenever you select LIS, LON, MAD,

PAR, ROM, BER, STO, ATH, MOW, TYO, ANC, YVR, LAX, YEA, DEN, MEX, CHI,

NYC, YHZ, or YYT as your Home City code.

•If you experience problems receiving the time calibration signal in your area, it

probably is best to switch between Standard Time and Daylight Saving Time

(summer time) manually.

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to cycle through the DST settings in the

sequence shown below.

Auto DST (

AvtA

) DST off (

OFF

) DST on (

)

DST indicator

•If you change your Home City to one that is within the same transmitter area, the

current DST setting will be retained. If you change to a city that is outside your

current transmitter area, DST will be turned off automatically.

Transmitter

Japan

China

U.S.

Europe (U.K., Germany)

None

Covered City Codes

TPE, SEL, TYO

HKG, BJS

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ, YYT

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW

All other city codes

4. When the setting you want is selected, press A to exit the setting screen.

• The DST indicator appears to indicate that Daylight Saving Time is turned on.

Reference

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Graphic Area

The information shown in the graphic area depends on the current mode.

Mode

Timekeeping Mode

World Time Mode

Alarm Mode

Stopwatch Mode

CountdownTimer Mode

Graphic Area

Timekeeping Mode seconds

No indication

Stopwatch Mode 1/10 seconds

CountdownTimer Mode seconds

Graphic Area

Button Operation Tone

The button operation tone sounds any time you press one

of the watch’s buttons. You can turn the button operation

tone on or off as desired.

•Even if you turn off the button operation tone, alarms,

the Hourly Time Signal, and other beepers all operate

normally.

To turn the button operation tone on and off

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C nine times until the current button operation

tone setting ( or ) appears.

3. Press D to toggle the setting between (tone on)

and (tone off).

4. Press A to exit the setting screen.

•The mute indicator is displayed in all modes when the

button operation tone is turned off.

Mute indicator

Power Saving Function

When turned on, the Power Saving function enters a

sleep state automatically whenever the watch is left in an

area for a certain period where it is dark. The table below

shows how watch functions are affected by the Power

Saving function.

Power saving indicator

Elapsed Time

in Dark

60 to 70 minutes

6 or 7 days

Display

Blank, with Power Saving

indicator flashing

Blank, with Power Saving

indicator not flashing

Operation

All functions enabled, except for the

display

Auto receive, beeper tone,

illumination, and display are disabled.

•Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.

•The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch

is already in the sleep state when 6:00 AM arrives, however, it will remain in the

sleep state.

To recover from the sleep state

Perform any one of the following operations.

•Move the watch to a well-lit area.

•Press any button.

•Angle the watch towards your face for reading.

To turn Power Saving on and off

1. In the Timekeeping Mode, hold down A until the city

code starts to flash, which indicates the setting screen.

2. Press C 11 times until the Power Saving on/off screen

appears.

3. Press D to toggle Power Saving on ( ) and off ( ).

4. Press A to exit the setting screen.

•The Power Saving indicator is on the display in all

modes while Power Saving is turned on.

On/Off status

Operation Guide 3179

Radio-controlled Atomic Timekeeping Precautions

•Strong electrostatic charge can result in the wrong time being set.

•The time calibration signal bounces off the ionosphere. Because of this, such factors

as changes in the reflectivity of the ionosphere, as well as movement of the

ionosphere to higher altitudes due to seasonal atmospheric changes or the time of

day may change the reception range of the signal and make reception temporarily

impossible.

•Even if the time calibration signal is received properly, certain conditions can cause

the time setting to be off by up to one second.

•The current time setting in accordance with the time calibration signal takes priority

over any time settings you make manually.

•The watch is designed to update the date and day of the week automatically for the

period January 1, 2000 to December 31, 2099. Setting of the date by the time

calibration signal cannot be performed starting from January 1, 2100.

•This watch can receive signals that differentiate between leap years and non-leap

years.

•Though this watch is designed to receive both time data (hour, minutes, seconds)

and date data (year, month, day), certain signal conditions can limit reception to time

data only.

•If you are in an area where proper time calibration signal reception is impossible, the

watch keeps the time with the precision noted in “Specifications”.

•If you have problems with proper time calibration signal reception or if the time

setting is wrong after signal reception, check your current city code, DST (summer

time), and auto receive settings.

•The Home City setting reverts to the initial default of TYO (Tokyo) whenever the

battery power level drops to Level 5 or when you have the rechargeable battery

replaced. If this happens, change the Home City to the setting you want.

Transmitters

The time calibration signal received by this watch depends on the currently selected

Home City code.

•When a U.S. time zone is selected, the watch receives the time calibration signal

transmitted from the United States (Fort Collins).

•When a Japanese time zone is selected, the watch receives the time calibration

signal transmitted from Japan (Fukushima and Fukuoka/Saga).

•When a European time zone is selected, the watch receives the time calibration

signals transmitted from Germany (Mainflingen) and England (Anthorn).

•When a China time zone is selected, the watch receives the time calibration signals

transmitted from China (Shangqiu City).

•When your Home City is LIS, LON, MAD, PAR , ROM, BER, STO, ATH, MOW

(which can receive both the Anthorn and Mainflingen signals), the watch first tries to

pick up the signal it last successfully received. If that fails, it tries the other signal. For

the first receive after you select your Home City, the watch tries the nearest signal

first (Anthorn for LIS, LON, Mainflingen for MAD, PAR , ROM, BER, STO, ATH, and

MOW).

Auto Return

•If you do not perform any operation for about two or three minutes while a setting

screen (with a flashing setting) is on the display, the watch will exit the setting screen

automatically.

Scrolling

The B and D are used in various modes and setting screens to scroll through data

on the display. In most cases, holding down these buttons during a scroll operation

scrolls at high speed.

Initial Screens

When you enter the World Time Mode or Alarm Mode, the data you were viewing

when you last exited the mode appears first.

Timekeeping

•Resetting the seconds to 00 while the current count is in the range of 30 to 59

causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are

reset to 00 without changing the minutes.

•The year can be set in the range of 2000 to 2099.

•The watch’s built-in full automatic calendar makes allowances for different month

lengths and leap years. Once you set the date, there should be no reason to change

it except after you have the watch’s battery replaced.

•The current time for all city codes in the Timekeeping Mode and World Time Mode is

calculated in accordance with the Coordinated Universal Time (UTC) for each city,

based on your Home City time setting.

World Time

•The seconds count of the World Time is synchronized with the seconds count of the

Timekeeping Mode.

Illumination Precautions

•The electro-luminescent panel that provides illumination loses power after very long

use.

•Illumination may be difficult to see when viewed under direct sunlight.

•The watch may emit an audible sound whenever the display is illuminated. This is

due to vibration of the EL panel used for illumination, and does not indicate

malfunction.

•Illumination turns off automatically whenever an alarm sounds.

•Frequent use of illumination runs down the battery.

Auto light switch precautions

•Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light

switch to operate when it is not needed, which shortens battery life. If you want to

wear the watch on the inside of your wrist, turn off the auto light switch feature.

•Illumination may not turn on if the face of the watch is

more than 15 degrees above or below parallel. Make

sure that the back of your hand is parallel to the ground.

•Illumination turns off after a preset amount of time (1.5

or 3 seconds), even if you keep the watch pointed

towards your face.

•Static electricity or magnetic force can interfere with proper operation of the auto

light switch. If illumination does not turn on, try moving the watch back to the starting

position (parallel with the ground) and then tilt it back toward you again. If this does

not work, drop your arm all the way down so it hangs at your side, and then bring it

back up again.

•Under certain conditions, illumination may not turn on until about one second after

you turn the face of the watch towards you. This does not necessarily indicate

malfunction of the auto light switch.

•You may notice a very faint clicking sound coming from the watch when it is shaken

back and forth. This sound is caused by mechanical operation of the auto light

switch, and does not indicate a problem with the watch.

More than 15 degrees

too high

Specifications

Accuracy at normal temperature: ± 15 seconds a month

Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week

Time format: 12-hour and 24-hour

Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099

Other: Home City code (can be assigned one of 48 city codes); Standard Time /

Daylight Saving Time (summer time)

Time Calibration Signal Reception: Auto receive 6 times a day (5 times a day for the

Chinese calibration signal) (Remaining auto receives cancelled as soon as

one is successful); Manual receive

Receivable Time Calibration Signals: Mainflingen, Germany (Call Sign: DCF77,

Frequency: 77.5 kHz); Anthorn, England (Call Sign: MSF, Frequency: 60.0

kHz); Fort Collins, Colorado, the United States (Call Sign: WWVB, Frequency:

60.0 kHz); Fukushima, Japan (Call Sign: JJY, Frequency: 40.0 kHz); Fukuoka/

Saga, Japan (Call Sign: JJY, Frequency: 60.0 kHz); Shangqiu City, Henan

Province, China (Call Sign: BPC, Frequency: 68.5 kHz)

World Time: 48 cities (31 time zones)

Other: Daylight Saving Time/Standard Time

Alarms: 5 daily alarms (four one-time alarms; one snooze alarm); Hourly Time Signal

Stopwatch:

Measuring unit: 1/100 second

Measuring capacity: 23:59' 59.99''

Measuring modes: Elapsed time, split time, two finishes

Countdown Timer:

Measuring unit: 1 second

Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)

Illumination: EL (electro-luminescent panel); Full Auto Light Switch; Selectable

illumination duration

Other: Button operation tone on/off

Power Supply: Solar cell and one rechargeable battery

Approximate battery operating time: 9 months (from full charge to Level 4) under

the following conditions:

•Watch not exposed to light

•Internal timekeeping

•Display on 18 hours per day, sleep state 6 hours per day

•1 illumination operation(1.5 second) per day

•10 seconds of alarm operation per day

•Approximately 4 minutes of signal reception per day

Frequent use of illumination runs down the battery. Particular care is required

when using the auto light switch.

City Code Table

Pago Pago

Honolulu

Anchorage

Vancouver

Los Angeles

Edmonton

Denver

Mexico City

Chicago

New York

Santiago

Halifax

St. Johns

Rio De Janeiro

Fernando de Noronha

Praia

Lisbon

London

Madrid

Paris

Rome

Berlin

Stockholm

Athens

Cairo

Jerusalem

–11

–10

–9

–8

–7

–6

–5

–4

–3.5

–3

–2

–1

PPG

HNL

ANC

YVR

LAX

YEA

DEN

MEX

CHI

NYC

SCL

YHZ

YYT

RIO

FEN

RAI

UTC

LIS

LON

MAD

PAR

ROM

BER

STO

AT H

CAI

JRS

City UTC Offset/

GMT Differential

City

Code City UTC Offset/

GMT Differential

City

Code

•Based on data as of June 2008.

•The rules governing global times (UTC offset and GMT differential) and summer

time are determined by each individual country.

MOW

JED

THR

DXB

KBL

KHI

DEL

KTM

DAC

RGN

BKK

SIN

HKG

BJS

TPE

SEL

TYO

ADL

GUM

SYD

NOU

WLG

Moscow

Jeddah

Te h r a n

Dubai

Kabul

Karachi

Delhi

Kathmandu

Dhaka

Yangon

Bangkok

Singapore

Hong Kong

Beijing

Taipei

Seoul

Tokyo

Adelaide

Guam

Sydney

Noumea

Wellington

+3.5

+4.5

+5.5

+5.75

+6.5

+9.5

+10

+11

+12

Casio G Shock Solar Atomic Watch Gw69001V Users Manual QW 3179

MO0905-EA qw3179

GW69001V to the manual d57f8b5c-6872-4429-ab2c-88067f66eb66

Navigation menu

Versions of this User Manual:

Views

Navigation