Casio Px 330 Users Manual PX330_e

Web-Px330E1B web-px330e1b

px-330 to the manual 69769c90-7fb0-442e-9487-3d4a76a12249

PX330 PX330_EN PX-330 | Electronic Musical Instruments | Manuals | CASIO

2015-01-21

: Casio Casio-Casio-Px-330-Users-Manual-243717 casio-casio-px-330-users-manual-243717 casio pdf

Open the PDF directly: View PDF .
Page Count: 72

PX330ES1B

USER’S GUIDE

GUÍA DEL USUARIO

Please keep all information for future reference.

Guarde toda documentación para futuras consultas.

Safety Precautions

Before trying to use the piano, be sure to read

the separate “Safety Precautions”.

Precauciones de seguridad

Antes de intentar usar el piano, asegúrese de

leer las “Precauciones de seguridad” separadas.

EnglishEspañol

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Important!

Please note the following important information before using this product.

• Before using the AD-A12150LW Adaptor to power the product, be sure to check the AC Adaptor for any damage first. Carefully check the

power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is seriously damaged.

• The product is not intended for children under 3 years.

• Use only the CASIO AD-A12150LW adaptor.

• The AC adaptor is not a toy.

• Be sure to disconnect the AC adaptor before cleaning the product.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit

from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury

from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.

When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For that purpose, locate

the apparatus in a way that secures easy access to the power cord.

Declaration of Conformity

Model Number: PX-330

Trade Name: CASIO COMPUTER CO., LTD.

Responsible party: CASIO AMERICA, INC.

Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801

Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the

equipment.

Manufacturer:

CASIO COMPUTER CO.,LTD.

6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Responsible within the European Union:

CASIO EUROPE GmbH

Casio-Platz 1, 22848 Norderstedt, Germany

This mark applies in EU countries only.

E-1

English

Contents

General Guide...........................E-2

Installing the Music Stand........................................... E-3

Saving Settings and Using Panel Lock....................... E-4

Returning the Digital Piano to Its

Factory Default Settings ............................................. E-4

Power Outlet .............................E-5

Using an AC Adaptor .................................................. E-5

Connections.............................. E-6

Connecting Headphones ............................................ E-6

Connecting a Pedal .................................................... E-6

Connecting Audio Equipment or an Amplifier ............. E-7

Bundled and Optional Accessories............................. E-8

Using Built-in Tones ................E-9

Turning on the Digital Piano and

Playing Something...................................................... E-9

Selecting a Tone......................................................... E-9

Layering Two Tones ................................................. E-10

Splitting the Keyboard between Two Tones ............. E-11

Using Octave Shift .................................................... E-12

Adjusting the Brilliance of a Tone ............................. E-12

Adding Reverb to the Tone....................................... E-13

Adding the Chorus Effect to the Tone....................... E-13

Using the Metronome ............................................... E-14

Using the Pitch Bend Wheel ..................................... E-15

Playing a Duet .......................................................... E-15

Using Auto

Accompaniment .....................E-17

Playing an Auto Accompaniment.............................. E-17

Using One-Touch Presets ........................................ E-20

Using Auto Harmonize.............................................. E-20

Creating Your Own Original Rhythms....................... E-21

Playing Demo Songs..............E-24

Playing Tone Demo Songs ....................................... E-24

Listening to Songs Loaded from an

External Source ........................................................ E-25

Music Presets .........................E-27

Selecting a Music Preset .......................................... E-27

Creating an Original User Preset.............................. E-28

Registering Tone and

Rhythm Setups.......................E-32

Saving Registration Data .......................................... E-33

Recalling a Registration............................................ E-33

Recording Your

Keyboard Play ........................E-34

Recording or Playing Back a Single Song ................E-34

Recording or Playing Back Multiple Songs ............... E-35

Recording to a Specific Track (Part) ......................... E-35

Deleting Recorder Data............................................. E-37

Re-recording Part of a Recorder Song

(Punch-in Recording) ................................................E-37

Other Settings.........................E-40

Configuring Settings.................................................. E-40

Using a Memory Card ............E-44

Loading and Removing a Memory Card ................... E-45

Formatting a Memory Card ....................................... E-45

Saving Digital Piano Data to a Memory Card............ E-46

Loading Data from a Memory Card........................... E-47

Deleting Memory Card Data...................................... E-47

Renaming a Memory Card File ................................. E-48

Playing Back a Song from a Memory Card............... E-48

Saving Data to Digital Piano Memory

(Internal Area) Instead of a Memory Card................. E-49

Error Messages......................................................... E-50

Connecting to a Computer ....E-51

Minimum Computer System Requirements .............. E-51

Connecting the Digital Piano to Your Computer ....... E-51

Using MIDI ................................................................ E-52

Transferring Data between the Digital Piano

and a Computer ........................................................ E-52

Reference ................................E-56

Troubleshooting ........................................................ E-56

Product Specifications............................................... E-57

Operating Precautions .............................................. E-58

Appendix ...................................A-1

Tone List ..................................................................... A-1

Drum Assignment List ................................................. A-3

Rhythm List ................................................................. A-4

Music Preset List......................................................... A-6

Fingering Guide........................................................... A-8

Chord Example List..................................................... A-9

MIDI Implementation Chart

Company and product names used in this

manual may be registered trademarks of others.

E-2

General Guide

3 4 5 6 bm bn bo bp7 bk

8 9 bl

ck cl cm cn co cp cq cr dm

br bs cs ct dk dl dn

bq ∗

dp dsdq dr dt ek

el em

BottomLeft Side

Back

General Guide

E-3

English

•This manual uses the numbers and names below to refer to buttons and controllers.

Insert the bottom of the music stand into the

groove on the top of the Digital Piano’s

console.

*Installing the Music Stand

1VOLUME controller

2INTRO/REPEAT button

3NORMAL/FILL-IN, sREW button

4VARIATION/FILL-IN, dFF button

5SYNCHRO/ENDING, PAUSE button

6START/STOP, PLAY/STOP button

7ACCOMP ON/OFF, PART button

8METRONOME button

9RECORDER button

bk TEMPO buttons

bl RHYTHM, USER SONGS button

bm POPS/JAZZ, MUSIC PRESET button

bn LATIN/WORLD, MUSIC PRESET button

bo BALLAD/PIANO RHYTHMS,

RHYTHM EDITOR button

bp USER RHYTHMS, RHYTHM EDITOR button

bq Display

br TONE, REGISTRATION button

bs FUNCTION button

bt w/NO, q/YES buttons

ck GRAND PIANO (MODERN) button

cl GRAND PIANO (CLASSIC) button

cm ELEC PIANO button

cn VIBES/CLAVI button

co ORGAN button

cp STRINGS/SYNTH-PAD button

cq BASS/GUITAR button

cr VARIOUS/GM TONES button

cs REVERB, REV TYPE, EXIT button

ct CHORUS, CHOR TYPE, u button

dk SPLIT, SPLIT POINT, i button

dl CARD/INTERNAL, SAVE/LOAD,

ENTER button

dm STORE, USB DEVICE MODE button

dn SD CARD SLOT

do PITCH BEND wheel

dp USB port

dq MIDI OUT/IN terminals

dr DAMPER, SOFT/SOSTENUTO PEDAL jacks

ds DC 12V terminal

dt LINE OUT R, L/MONO jacks

ek LINE IN R, L/MONO jacks

el POWER button

em PHONES jacks

en Pedal connector

E-4

General Guide

Your Digital Piano lets you save its current settings,

and lock its buttons to protect against operation errors.

For details, see “Setting Backup” (page E-43) and

“Panel Lock” (page E-43).

Perform the following procedure when you want to

return the Digital Piano’s stored data and settings to

their initial factory defaults.

Turn off the Digital Piano.

While holding down both the br (TONE) and

bs (FUNCTION) buttons, press the el

(POWER) button.

The Digital Piano will turn on and initialize its internal

system. You will be able to use the Digital Piano in a

short while.

NOTE

•See “Turning on the Digital Piano and Playing

Something” (page E-9) for information about

turning digital power on and off.

Saving Settings and Using

Panel Lock

Returning the Digital Piano to

Its Factory Default Settings

E-5

English

Power Outlet

Your Digital Piano runs on standard household power.

Be sure to turn off power whenever you are not using

the Digital Piano.

Use only the AC adaptor (JEITA Standard, with unified

polarity plug) that comes with this Digital Piano. Use

of a different type of AC adaptor can cause

malfunction of the Digital Piano.

Specified AC Adaptor: AD-A12150LW

•Use the supplied power cord to connect the AC

adaptor as shown in the illustration below.

Note the following important precautions to avoid

damage to the power cord.

During Use

•Never pull on the cord with excessive force.

•Never repeatedly pull on the cord.

•Never twist the cord at the base of the plug or

connector.

During Movement

•Before moving the Digital Piano, be sure to unplug

the AC adaptor from the power outlet.

During Storage

•Loop and bundle the power cord, but never wind it

around the AC adaptor.

IMPORTANT!

• Never connect the AC adaptor (JEITA Standard,

with unified polarity plug) that comes with this Digital

Piano to any other device besides this piano. Doing

so creates the risk of malfunction.

• Make sure the Digital Piano is turned off before

plugging in or unplugging the AC adaptor.

• The AC adaptor will become warm to the touch after

very long use. This is normal and does not indicate

malfunction.

Using an AC Adaptor

Household power outlet

Power cordDC 12V terminal

AC adaptor

E-6

Connections

IMPORTANT!

• Before connecting headphones, be sure to use the

Digital Piano’s VOLUME controller to turn the

volume down to a low level. After connecting, you

can adjust the volume to the level you want.

• The Digital Piano automatically adjusts sound output

to optimize for headphones (when headphones are

connected) or the built-in speakers (when

headphones are not connected).

Left Side

Connect commercially available headphones to the

PHONES jacks. Connecting headphones to either of

the PHONES jacks cuts off output to the speakers,

which means you can practice even late at night

without bothering others. To protect your hearing,

make sure that you do not set the volume level too high

when using headphones.

The back of the Digital Piano has two pedal jacks, one

for a damper pedal and one for a soft/sostenuto pedal.

To connect to the pedal jack

Depending on the type of operation you want the

pedal (SP-3) to perform, connect the pedal’s cable

either to the Digital Piano’s DAMPER PEDAL jack or

SOFT/SOSTENUTO PEDAL jack. If you want to use

both operations (jacks) at the same time, you need to

purchase another optionally available pedal.

Back

NOTE

•You can connect a pedal to the SOFT/SOSTENUTO

PEDAL jack and apply either a soft or sostenuto

effect to the notes you play. For details, see “Soft/

Sostenuto Pedal Jack Setting” (page E-43).

Pedal Functions

zDamper Pedal

Pressing the damper pedal while playing will cause the

notes you play to reverberate for a very long time.

•Whenever a piano tone is selected, pressing this

pedal will activate the Digital Piano’s Acoustic

Resonance effect, which causes notes to resonate in

the same way they do when the damper pedal on an

acoustic piano is pressed. For details, see “Acoustic

Resonance” (page E-41).

zSoft Pedal

Pressing this pedal suppresses notes played on the

keyboard after the pedal was pressed, and makes them

sound softer.

zSostenuto Pedal

Only the notes that are played while this pedal are

depressed are sustained until the pedal is released.

Connecting Headphones

Connecting a Pedal

PHONES jacks

Commercially available

headphones

Mini plug

PEDAL jacks

SP-3

English

Connections

E-7

Pedal Connector

You can connect the optionally available 3-Pedal Unit

(SP-32) to the pedal connector on the bottom of the

Digital Piano. You can then use the pedals for

expression that is similar to that available on an

acoustic piano.

NOTE

•The SP-32 Pedal Unit supports half-pedal operation

(pressing the pedal part way). You can adjust the

amount of the effect is applied when the damper

pedal is pressed part way. For details, see “Half

Pedal Effect” (page E-43).

•The optionally available CS-67P special stand is

required in order to use the SP-32 Pedal Unit.

You can connect audio equipment or a music amplifier

to the Digital Piano and then play through external

speakers for more powerful volume and better sound

quality.

IMPORTANT!

• The Digital Piano automatically adjusts sound output

to optimize for headphone output (when headphones

are connected) or built-in speaker output (when

headphones are not connected). This also will cause

a change in the output quality from the Digital

Piano’s LINE OUT R and L/MONO jacks.

• Whenever connecting a device to the Digital Piano,

first use the VOLUME controller to set the volume to

a low level. After connecting, you can adjust the

volume to the level you want.

• Whenever you connect any device to the Digital

Piano, be sure to read the user documentation that

comes with the device.

Pedal connector

Bottom

Connecting Audio Equipment

or an Amplifier

INPUT 1

INPUT 2

Guitar amplifier

Keyboard amplifier, etc.

Standard plug

Standard jack

LEFT (White)

RIGHT (Red)

Tape recorder,

MIDI sound source, etc.

Audio amplifier AUX IN jack, etc.

Pin plug

E-8

Connections

Playing Output from External Equipment

through the Piano’s Speakers 1

Use commercially available cables to connect the

external audio equipment to the piano’s LINE IN jacks

as shown in Figure 1.

LINE IN R jack input sounds through the piano’s right

speaker, while LINE IN L/MONO jack input sounds

through the left speaker. Connecting to the LINE IN

L/MONO jack only causes the same output to be

produced from both speakers. It is up to you to

purchase connecting cables that are compatible with

the equipment you are connecting.

Connecting to Audio Equipment 2

Use commercially available cables to connect the

external audio equipment to the piano’s LINE OUT

jacks as shown in Figure 2. LINE OUT R jack output is

right channel sound, while LINE OUT L/MONO jack

output is left channel sound. It is up to you to purchase

connecting cables like the ones shown in the

illustration for connection of audio equipment.

Normally in this configuration you must set the audio

equipment’s input selector to the setting that specifies

the terminal (such as AUX IN) to which the piano is

connected. Use the piano’s VOLUME controller to

adjust the volume level.

Connecting to a Musical Instrument

Amplifier 3

Use commercially available cables to connect the

amplifier to the piano’s LINE OUT jacks as shown in

Figure 3. LINE OUT R jack output is right channel

sound, while LINE OUT L/MONO jack output is left

channel sound. Connecting to the LINE OUT

L/ MONO jack only outputs a mixture of both

channels. It is up to you to purchase connecting cable

like the one shown in the illustration for connection of

the amplifier. Use the piano’s VOLUME controller to

adjust the volume level.

Use only accessories that are specified for use with this

Digital Piano.

Use of unauthorized accessories creates the risk of fire,

electric shock, and personal injury.

NOTE

•You can get information about accessories that are

sold separately for this product from the CASIO

catalog available from your retailer, and from the

CASIO website at the following URL.

http://world.casio.com/

Bundled and Optional

Accessories

E-9

English

Using Built-in Tones

Press the el (POWER) button.

This turns on power.

•To turn off the Digital Piano, press the el button

again.

After a short while, the display screen should

appear as shown below, which indicates that

the Digital Piano is ready to be played.

Use the 1 (VOLUME) controller to adjust the

volume level.

Play something on the keyboard.

Your Digital Piano has 250 tones, divided into eight

groups.

•For more information, see the “Tone List” (page

A-1).

•The Digital Piano has built-in demonstration tunes

that highlight the different characteristics of tones.

For more information, see “Playing Tone Demo

Songs” (page E-24).

Press the br (TONE) button so its upper lamp

is lit.

•Each press of the button toggles between the upper

and lower lamps.

IMPORTANT!

• Continuing on to the next step while the

REGISTRATION lamp is lit will perform a registration

recall operation (page E-32), which will change the

setup of the Digital Piano. Make sure that the TONE

lamp is lit before you advance to the next step.

Use the “Tone List” (page A-1) to look up the

group and the number of the tone you want to

select.

dlENTER

dkSPLIT, ibsFUNCTION

1VOLUME

7PA R T

bkTEMPO

csREVERB

brTONE

ctCHORUS, ubtw, q8METRONOME

blUSER SONGS

ck–crTone groups

Turning on the Digital Piano

and Playing Something

el button

Left Side

Selecting a Tone

Lit

E-10

Using Built-in Tones

Use the ck to cr (tone groups) buttons to

select the group you want.

Example: To select the ORGAN group

Use the bt (w, q) buttons to select the

tone you want.

Example: To select “002 Jazz Organ”

NOTE

•Pressing q and w at the same time will jump to

tone 001 of the currently selected group. Holding

down either button changes the tone number at high

speed.

•See page E-40 for more information about scrolling.

You can layer two different tones so they play at the

same time when you press a keyboard key.

•The first tone you select is called the “main tone,”

while the second tone is called the “layered tone.”

Select the main tone.

Example: To select MELLOW PIANO in the CLASSIC

group, press the cl (CLASSIC) button and

then use the bt (w, q) buttons to select

“002 Mellow Piano”.

Hold down the button of the group that

contains the tone you want to select as the

layered tone until “LAYER: ON” appears on

the display as shown below for a few

moments.

This will layer the tones currently selected in the two

groups.

The button you held down in step 2 will light to

indicate that it is selected.

Example: When BASS/GUITAR group is selected

Use the bt (w, q) buttons to select the

tone you want in the group you selected in

step 2.

Example: When “006 Picked Bass” is selected

To unlayer the tones and return the keyboard

to a single tone, press any one of the tone

group buttons.

NOTE

•You can adjust the balance between the main tone

and layered tone. For details, see “Layered Tone

Volume (Layer Balance)” (page E-41).

Layering Two Tones

Lit

Tone number

Tone name

Lit

Layered tone number

Layered tone name

English

Using Built-in Tones

E-11

You can split the keyboard so the left side (lower

range) plays one tone and the right side (upper range)

plays a different tone.

Example: To split the keyboard between the GM SLAP

BASS 1 tone on the left (lower range) and the

GRAND PIANO tone on the right (upper range).

Press the dk (SPLIT) button.

This causes the SPLIT lamp to light, indicating that the

keyboard is split between two tones.

Select the tone you want to assign to the left

side (lower range) of the keyboard.

Example: To select GM SLAP BASS 1 in the VARIOUS/

GM TONES group, press the cr (VARIOUS/

GM TONES) button and then use the bt (w,

q) buttons to select “073 GM SlapBass1”.

To unsplit the keyboard and return it to a

single tone, press the dk (SPLIT) button.

The SPLIT lamp will go out, indicating that the

keyboard is no longer split.

NOTE

•If the keyboard is set up with layered tones (page

E-10) when you perform the above split operation,

the layered tones will play on the right (upper

range) side of the keyboard.

Moving the Keyboard Split Point

You can use the procedure below to specify the

location on the keyboard where it splits between the

left side and the right side. That location is called the

“split point”.

Hold down the dk (SPLIT) button until the

split point setting screen appears on the

display as shown below.

Press the keyboard key where you want to

specify as the leftmost key of the right (upper

range) tone.

This specifies the split point.

Press the dk (SPLIT) button.

This exits the split point screen.

Splitting the Keyboard

between Two Tones

Left (Lower Range)

Tone: GM SLAP BASS 1

Right (Upper Range)

Tone: GRAND PIANO

Lit

Left tone number

Left tone name

Left (Lower Range) side Right (Upper Range) side

Split point

Current split point key name

E-12

Using Built-in Tones

After you split the keyboard (page E-11), you may find

out that the lower range notes on the left are too low or

that the upper range notes on the right are too high.

You can use octave shift to shift the octaves of the

upper range and lower range upwards or downwards

in octave units.

While holding down the bs (FUNCTION)

button, press the br (TONE) button.

This displays the octave shift screen.

Use the 7 (PART) button to select the range

whose octave you want to change.

•Each press of 7 (PART) cycles through the ranges

below.

Use the bt (w, q) buttons to shift the

octave of the currently selected range.

•You can shift the octave within the range of –2 to 0 to

Press the bs (FUNCTION) button.

This exits the octave shift screen.

NOTE

•Octave shift also can be performed as described for

“Octave Shift” (page E-41).

Press the bs (FUNCTION) button.

The FUNCTION lamp will light and the function screen

will appear on the display.

Use the dk (i) and ct (u) buttons to select

the Tmpr/Effect screen.

Press the dl (ENTER) button.

This will display a screen for selecting settings in the

Tmpr/Effect group.

Use the dk (i) or ct (u) button to select

the brilliance screen shown below.

Use the

(

) buttons to adjust the

brilliance of the currently selected tone. You

can adjust brilliance in the range of –3 to 0 to 3.

Press the bs (FUNCTION) button.

This will exit the brilliance screen and cause the

FUNCTION lamp to go out.

NOTE

•See “Other Settings” (page E-40) for details about

using the bs (FUNCTION) button.

Using Octave Shift

Shift amount

Currently selected range

U1 (Upper1): Main tone

U2 (Upper2): Layered tone

L1 (Lower1): Left (lower range) tone

Adjusting the Brilliance of a

Tone

w: Mellower and softer

q: Brighter and harder

Lit

English

Using Built-in Tones

E-13

Press the cs (REVERB) button to toggle

reverb on and off.

Selecting the Reverb Type

You can select from among the following four types of

reverb.

1: Room

2: Hall

3: Large Hall

4: Stadium

Hold down the cs (REVERB) button until the

reverb type selection screen shown below

appears on the display.

Use the bt (w, q) buttons to select the

reverb type you want.

Press the cs (REVERB) button to exit the

reverb type screen.

Press the ct (CHORUS) button to toggle

chorus (which adds depth to a tone) on and

off.

Selecting the Chorus Type

You can select from among the following four chorus

types.

1: LightChorus

2: Chorus

3: Deep Chorus

4: Flanger

Hold down the ct (CHORUS) button until the

chorus type selection screen shown below

appears on the display.

Use the bt (w, q) buttons to select the

chorus type you want.

Press the ct (CHORUS) button to exit the

chorus type screen.

Adding Reverb to the Tone

Lit when on

Adding the Chorus Effect to

the Tone

Lit when on

E-14

Using Built-in Tones

Press the 8 (METRONOME) button.

This will start the metronome.

Press the 8 (METRONOME) button again to

stop the metronome.

Changing the Beats Per Measure

You can specify from two to six beats per measure for

the metronome. After you do, a chime will sound at the

beginning of each measure. Specifying 0 for this setting

will sound a straight beat, without a chime. This setting

lets you practice with a steady beat.

Hold down the 8 (METRONOME) button

until the number of beats per measure screen

shown below appears on the display.

Use the bt (w, q) buttons to select the

beats per measure value you want.

Press the 8 (METRONOME) button to exit

the number of beats per measure screen.

Changing the Tempo Setting

There are two different methods you can use to change

the tempo setting: by pressing q (faster) and w

(slower) buttons or by tapping a beat with a button.

■To adjust the tempo using q and w

buttons

Use the bk (TEMPO w, q) buttons to

adjust the tempo setting.

Each press of a button increases or decreases the beats

per minute value by one.

•Holding down either button changes the value at

high speed.

•You can specify a tempo value in the range of 20 to

255.

■To adjust the tempo by tapping a beat

While holding down the bs (FUNCTION)

button, tap the q bk (TEMPO) button four

times in time with the beat you want to

specify.

•The tempo setting will change in accordance with the

timing of your tapping.

•After you use this method to specify the approximate

tempo, you can then use the procedure under “To

adjust the tempo using q and w buttons” to adjust

the setting to a more exact value.

Using the Metronome

Lights with the first beat

of each measure

Lights with each subsequent beat of

each measure

Tempo value

Tap four times

English

Using Built-in Tones

E-15

Adjusting the Metronome Volume

You can use the following procedure to adjust the

volume level of the metronome, without affecting the

volume of Digital Piano output.

While holding down the bs (FUNCTION)

button, press the 8 (METRONOME) button.

This displays the metronome volume screen.

Use the bt (w, q) buttons to adjust the

metronome volume.

Press the bs (FUNCTION) button.

This will exit the metronome volume screen and cause

the FUNCTION lamp to go out.

NOTE

•You also can use the procedure under “Metronome

Volume” (page E-41) to adjust the metronome

volume.

You can use the pitch bend wheel to slide the pitch of

notes smoothly upwards and downwards. This

capability makes it possible to reproduce saxophone

and electric guitar choking effects.

Adding a Pitch Bend Effect

While playing a note on the

keyboard, rotate the pitch bend

wheel on the left of the keyboard

upwards or downwards.

The amount the note bends depends on

how much you rotate the pitch bend

wheel.

•Do not have the pitch bend wheel

rotated as you turn on the Digital Piano.

NOTE

•You also can configure pitch bend wheel operation

by specifying the amount of pitch change at

maximum rotation in either direction. See “Pitch

Bend Range” (page E-43) for more information.

You can use the Duet Mode to split the Digital Piano’s

keyboard in the center so two people can play a duet.

This makes it possible to configure the keyboard so, for

example, the teacher can play on the left and the

student can follow along on the right. Or one person

can play the left hand part on the left, while another

plays the right hand part on the right.

Pedal Operation when Playing a Duet

zOptional SP-32 Pedal Unit

zOptional SP-3 Pedal Unit

To use the SP-3 Pedal Unit as the right keyboard

damper pedal, connect it to the dr (DAMPER PEDAL)

terminal.

•Half-pedal operation is not supported in this case.

To use the SP-3 Pedal Unit as the left keyboard (initial

default setting) or right keyboard damper pedal

(selectable), connect it to the dr (SOFT/SOSTENUTO

PEDAL) terminal.

•For information about how to select left or right

keyboard control with the SP-3 Pedal Unit, see

“Soft/Sostenuto Pedal Jack Setting” (page E-43).

Using the Pitch Bend Wheel

Metronome volume

Playing a Duet

C3 C4 C5 C6 C3 C4 C5 C

Right keyboardLeft keyboard

(Middle C) (Middle C)

Left and right side damper pedal

Left keyboard

damper pedal

Right side damper pedal

(Half-pedal operation

supported)

E-16

Using Built-in Tones

Configuring the Digital Piano for Duet

Play

Press the bl (USER SONGS) button so its

lower lamp is lit.

•To practice with songs stored on a memory card,

press the dl (CARD/INTERNAL) button so its lamp

is lit in place of the bl (USER SONGS) button.

While holding down the bs (FUNCTION)

button, press the dk (SPLIT) button.

This causes the Duet Mode on/off screen to appear.

•The keyboard keys are disabled while this screen is

displayed.

Press the bt (q) button to turn on the Duet

Mode.

This will cause the dk (SPLIT) button lamp to flash.

Press the bs (FUNCTION) button.

This exits the Duet mode on/off screen and configures

the Digital Piano’s keyboard for duet play.

To turn off the Duet Mode, press the dk

(SPLIT) button so the SPLIT lamp goes out.

NOTE

•You also can use the procedure under “Duet Mode”

(page E-41) to turn the Duet Mode on or off.

Changing the Octave of a Duet Mode

Keyboard

You can use the following procedure to change the

octave of the left and right Duet Mode keyboards.

While holding down the bs (FUNCTION)

button, press the dk (SPLIT) button.

This displays the Duet Mode on/off screen shown in

step 2 under “Configuring the Digital Piano for Duet

Play” (page E-16). If the Duet Mode is currently turned

off, press the bt (q) button to turn it on.

Of the four C keys in the left keyboard, press

the one that you want to have located at

middle C.

•This will sound the note assigned to C4 and change

the octave of the left keyboard.

Example: To change the configuration so the leftmost C

key is middle C as shown below.

You can use the same procedure as step 2 to

select one of the C keys in the right keyboard

to shift its octave as well.

Press the bs (FUNCTION) button.

This exits the Duet Mode on/off screen and causes the

bs (FUNCION) button lamp to go out.

The left and right keyboards will be configured

according to your settings.

NOTE

•Turning off the Duet Mode will clear your octave

shift settings and return the keyboard to its initial

default settings.

Lit

C4 C5 C6 C7 C3 C4 C5 C6

1 octave higher than initial setting Unchanged

Leftmost C key (Pressed key)

E-17

English

Using Auto Accompaniment

With Auto Accompaniment, simply select the

accompaniment rhythm you want and the matching

accompaniment (drums, guitar, etc.) will play

automatically when you play a chord with your left

hand. It’s like having your own personal backup group

along with you wherever you go.

This Digital Piano has 180 built-in Auto

Accompaniment patterns, which are divided into three

groups. You can edit built-in rhythms to create your

own original rhythms (called “user rhythms”), which

you can save in a fourth group. For more information,

see the “Rhythm List” (page A-4).

Press the bl (RHYTHM) button so its upper

lamp is lit.

This enables Auto Accompaniment.

•Each press of the button toggles between the

RHYTHM and USER SONGS lamps.

Use the “Rhythm List” (page A-4) to look up

the group and the number of the rhythm you

want to select.

Use the bm to bp (rhythm groups) buttons to

select the group you want.

Example: When the LATIN/WORLD group is selected

Use the bt (w, q) buttons to select the

rhythm you want.

Example: When “005 Samba 2” is selected

Use the bk (TEMPO w, q) buttons to

adjust the tempo setting.

•This is the same as metronome tempo adjustment

(page E-14).

•To return the rhythm to its standard tempo setting,

press the bk (TEMPO w, q) buttons at the same

time.

bkTEMPO

csEXIT

brTONE dlENTER

btw/NO, q/YES

blRHYTHM

7ACCOMP ON/OFF

5SYNCHRO/ENDING boBALLAD/PIANO RHYTHMS

6START/STOP bpUSER RHYTHMS

2–5Accompaniment

patterns

ck–crInstrument parts

bm–bpRhythm groups

Playing an Auto

Accompaniment

Lit

Rhythm number

Rhythm name

Measure

Tempo

E-18

Using Auto Accompaniment

Press the 7 (ACCOMP ON/OFF) button so

its lamp is lit.

This turns ACCOMP on, so all accompaniment parts

sound.

•Turning ACCOMP off so the ACCOMP lamp is unlit

causes only the percussion instrument parts to sound.

•Each press of the 7 (ACCOMP ON/OFF) button

toggles ACCOMP on and off.

Press the 5 (SYNCHRO/ENDING) button.

This puts Auto Accompaniment into “synchro

standby”. Playing a chord during synchro standby will

cause Auto Accompaniment to start to play

automatically.

•Pressing the 2 (INTRO) button while Auto

Accompaniment is in synchro standby will enter

intro standby. Pressing the 4 (VARIATION) button

will enter variation standby. For details about intro

and variation patterns, see “Modifying Auto

Accompaniment Patterns” (page E-20).

Play the chord you want on the chord

keyboard (left keyboard keys).

Auto Accompaniment will start playing when you play

the chord.

•To start percussion part play without playing a

chord, press the 6 (START/STOP) button.

Example: To play a C chord

Play other chords with left hand as you play

the melody with your right hand.

•You can use “CASIO Chord” or other simplified

chord fingering modes to play chords. For details, see

“Selecting a Chord Fingering Mode” in the following

section.

•You can use the 3 (NORMAL) and 4

(VARIATION) buttons to modify accompaniment

patterns. For details, see “Modifying Auto

Accompaniment Patterns” (page E-20).

10.

When you are finished, press the 6 (START/

STOP) button again to stop Auto

Accompaniment.

•Pressing the 5 (SYNCHRO/ENDING) button

instead of the 6 (START/STOP) button will play an

ending pattern before stopping Auto

Accompaniment play. For details about ending

patterns, see “Modifying Auto Accompaniment

Patterns” (page E-20).

NOTE

•You can use the following procedure to adjust the

volume level of the Auto Accompaniment, without

affecting the volume of Digital Piano output. For

details, see “Auto Accompaniment Volume” (page

E-41).

•You can change the size of the chord keyboard by

using the split feature to move the split point (page

E-11). The keyboard keys to the left of the split point

make up the chord keyboard.

Lit

Flashing

Chord keyboard Melody keyboard

English

Using Auto Accompaniment

E-19

Selecting a Chord Fingering Mode

You can select from among the following five chord

fingering modes.

1: Fingered 1

2: Fingered 2

3: Fingered 3

4: CASIO Chord

5: Full Range

Hold down the 7 (ACCOMP ON/OFF) button

until the chord type selection screen appears

on the display.

Use the bt (w, q) buttons to select the

chord fingering mode you want.

Press the 7 (ACCOMP ON/OFF) button.

This exits the chord fingering screen.

■Fingered 1, 2, 3

With these three chord fingering modes, you play

chords on the chord keyboard using their normal

chord fingerings. Some chord forms are abbreviated,

and can be fingered with one or two keys.

For information about the types of chords you can

finger and their fingerings, see the “Fingering Guide”

(page A-8).

■CASIO CHORD

With “CASIO Chord”, you can use simplified

fingerings to play the four types of chords described

below.

When pressing more than one chord keyboard key,

makes no difference whether the additional keys are

white or black.

■FULL RANGE CHORD

With this chord fingering mode, you can use the full

range of the keyboard to play chords and the melody.

For information about the types of chords you can

finger and their fingerings, see the “Fingering Guide”

(page A-8).

Fingered 1: Play the component notes of the chord on the

keyboard.

Fingered 2: Unlike Fingered 1, 6th input is not possible with

this mode.

Fingered 3: Unlike Fingered 1, this mode allows input of

fraction chords with the lowest keyboard note as

the bass note.

Chord fingering mode

Chord keyboard

Chord Type Example

Major Chords

Press one key, whose note

corresponds to the chord

name.

• To play C Major, press any

C key in the chord

keyboard. The octave of the

note does not matter.

C (C Major)

Minor Chords

Press the chord keyboard key

that corresponds to the major

chord, while also pressing one

other chord keyboard key to

the right.

Cm (C minor)

Seventh Chords

Press the chord keyboard key

that corresponds to the major

chord, while also pressing

two other chord keyboard

keys to the right.

C7 (C seventh)

Minor Seventh Chords

Press the chord keyboard key

that corresponds to the major

chord, while also pressing

three other chord keyboard

keys to the right.

Cm7 (C minor seventh)

Chord keyboard

CCDE F

Note name

CCDE F

Melody keyboard

Chord keyboard

E-20

Using Auto Accompaniment

Modifying Auto Accompaniment Patterns

There are six different Auto Accompaniment patterns,

shown below. You can switch between patterns during

accompaniment play and even modify patterns. Use

buttons 2 through 5 to select the pattern you want.

*1 Press at the beginning of a song.

Accompaniment play proceeds with the normal

pattern after the intro pattern is complete. Pressing

the 4 (VARIATION/FILL-IN) button before

pressing this button will proceed with the variation

pattern after the intro pattern is complete.

*2 Press while a normal pattern is playing to insert a

fill-in pattern.

*3 Press while a variation pattern is playing to insert a

fill-in variation pattern.

*4 Press at the end of a song.

This will play an ending pattern and then stop Auto

Accompaniment.

One-Touch Preset gives you one-touch access to tone

and tempo settings that go well with the currently

selected Auto Accompaniment rhythm pattern.

Hold down the bl (RHYTHM) button for at

least two seconds.

This will configure tone, tempo, and other settings to

match the currently selected rhythm pattern. At this

time, Auto Accompaniment play also will go into

synchro standby, which means that Auto

Accompaniment will start to play automatically when

you finger a chord.

Play a chord on the keyboard.

This will start Auto Accompaniment play.

NOTE

•One-Touch Presets are not supported for user

rhythms (001 through 010 of the USER RHYTHMS

group).

Auto Harmonize lets you add harmony to melody

notes you play with your right hand. You can select

any one of 12 Auto Harmonize settings.

Press the br (TONE) button so its lamp is lit.

Hold down the br (TONE) button until the

auto harmonize screen appears on the

display.

Intro *1Normal Variation Ending *4

2345

Normal fill-in *2Variation fill-in *3

Using One-Touch Presets

Using Auto Harmonize

Lit

Type number Type name

English

Using Auto Accompaniment

E-21

Use the bt (w, q) buttons to select the

Auto Harmonize type you want.

Press the br (TONE) button.

This will exit the auto harmonize screen.

While playing chords, play the melody on the

keyboard.

Harmony will be added to your melody notes based on

the chords you play.

You can use rhythm editing to modify a built-in Auto

Accompaniment rhythm to create an original “user

rhythm” of your own. You can select a part (drum,

bass, etc.) of a normal, intro, or other pattern (page

E-20) and turn it on or off, adjust its volume level, and

perform other operations.

Select the number of the Auto

Accompaniment rhythm you want to edit.

At the same time, press the bo (BALLAD/

PIANO RHYTHMS) and bp (USER

RHYTHMS) buttons.

This displays the rhythm editor screen.

Use the accompaniment pattern buttons (2

through 5) to select the pattern (normal,

intro, ending, etc.) you want to edit.

The button you press will light, indicating that the

pattern is being edited.

•Each press of 3 (NORMAL/FILL-IN) toggles

between NORMAL and FILL-IN, and each press of

4 (VARIATION/FILL-IN) toggles between

VARIATION and FILL-IN. The applicable button

flashes while the fill-in pattern is selected.

Example: When intro is selected

Type

Number

Type Name Description

00 Off Turns off Auto Harmonize.

01 Duet 1

Adds close (separated by two to

four degrees) one-note harmony

below the melody note.

02 Duet 2

Adds open (separated by more

than 4 to 6 degrees) 1-note

harmony below the melody

note.

03 Country Adds country style harmony.

04 Octave Adds the note from the next

lower octave.

05 5th Adds the fifth degree note.

06 3-Way Open Adds 2-note open harmony, for

a total of three notes.

07 3-Way Close Adds 2-note close harmony, for

a total of three notes.

08 Strings Adds harmony that is optimal

for strings.

09 4-Way Open Adds 3-note open harmony, for

a total of four notes.

10 4-Way Close Adds 3-note close harmony, for

a total of four notes.

11 Block Adds block chord notes.

12 Big Band Adds big band style harmony.

Creating Your Own Original

Rhythms

2345

E-22

Using Auto Accompaniment

Use the instrument part buttons (ck through

cr) to select the part (drums, bass etc.) you

want to edit.

The name of the part you select will appear on the

display. Rhythm patterns are made up of the eight parts

shown below.

•Button illumination does not change when you press

the instrument part buttons (ck through cr). Button

illumination indicates whether there is

accompaniment data corresponding to each part.

Example: When bass is selected

Edit the selected part as desired.

The table below describes the parameters you can edit.

•Use the ct (u) and dk (i) buttons to select a

parameter, and the bt (w, q) buttons to change its

setting. You also can use shortcut buttons (see table

below) to select parameters.

•Pressing the bt (w, q) buttons at the same time

will return the currently selected parameter to its

initial default setting.

•Pressing the 6 (START/STOP) button during an

edit operation will sound the accompaniment pattern

with the edits you have made up to that point.

Pressing the 7 (ACCOMP ON/OFF) button will

sound only the instrument part you are editing.

Procedure continues on page E-23.

ck cl cm cn co cp cq cr

Drums Percus-

sion

Bass Chord 1 Chord 2 Chord 3 Chord 4 Chord 5

Parts

Instrument part name

Parameter Description Setting

Shortcut

Button

Rhythm

Select:

Rhythm

Replaces the part

(drum, bass, etc.)

accompaniment

data with that of

the specified

rhythm number. *1

001 to 190:

Rhythm

number *2*3

Tone

Select:

Tone

Switches the part

tone (instrument)

to that of the

specified tone

number.

001 to 250: Tone

Numbers *2*4bn

Prt:

Part on/

off

Toggles each part

on or off.

OFF:

Mutes the part.

ON:

Sounds the

part.

Vol:

Volume

level

Controls the

volume level of

each part.

000 to 127

Pan:

Panning

(position)

Controls whether

the sound of the

part can be heard

from the left side or

right side.

–64 to 0 to 63 *5

Reverb:

Reverb

Controls the level

of the reverb effect

(page E-13) applied

to the part notes.

000 to 127

Chorus:

Chorus

Controls the level

of the chorus effect

(page E-13) applied

to the part notes.

000 to 127

*1 Replacing part accompaniment data clears all edits to the

currently selected accompaniment data made up to that

point.

*2 Sequential numbers starting from 001, which is the first

rhythm of the first group (POPS/JAZZ). See the “Tone

List” (page A-1) and “Rhythm List” (page A-4) for

information on the numbering system.

*3 In the case of the intro and ending, specifying a rhythm

for one part (drum, bass, etc.) will cause the same rhythm

to be specified automatically for all of the other parts of

the pattern.

*4 Only drum set sounds (tone numbers 237 through 250)

can be selected for drum parts and percussion parts.

Drum set sounds cannot be selected for the bass and the

chord 1 through chord 5 parts.

*5 A smaller value shifts leftward, while a larger value shifts

rightward. A value of zero specifies center.

English

Using Auto Accompaniment

E-23

Repeat steps 3 through 5 to edit all of the

accompaniment patterns and parts you want.

After editing is complete, adjust the tempo of

the rhythm as desired.

•The tempo you set here becomes the initial default

tempo of the rhythm.

Press the cs (EXIT) button.

This causes a confirmation message to appear asking if

you want to save your edits.

Press the bt (YES) button.

This displays a screen for specifying the user rhythm

number and rhythm name.

•If you want to exit the editing operation without

saving, press the bt (NO) button instead of the bt

(YES) button.

10.

Decide on the user rhythm number where you

want to save the rhythm and a rhythm name.

•Use the ct (u) and dk (i) buttons to move the

cursor to the user rhythm number and rhythm name

character you want to change. Use the bt (w, q)

buttons to select the number or character you want.

•The rhythm name characters you can select are

shown below. To input a space, press both of the bt

(w and q) buttons at the same time.

11.

Press the dl (ENTER) button.

This saves the data.

•If the rhythm number where you are saving the data

already has data saved to it, a message (Replace?) will

appear on the display to confirm whether you want

to replace the existing data with the new data.

IMPORTANT!

• Saving user rhythm data to a user rhythm number

that already has data will cause the existing data to

be replaced by the new data.

NOTE

•If the size of the accompaniment pattern or

instrument part data is too large to be edited, a

memory full message (Memory Full) will appear on

the display. If that happens, select a different

accompaniment pattern or instrument part for

editing.

Destination user rhythm number

Rhythm name

E-24

Playing Demo Songs

Your Digital Piano comes with eight built-in demo

tunes, which demonstrate the characteristics of each of

the eight tone groups.

While holding down the 7 (PART) button,

press the 6 (PLAY/STOP) button.

This will start sequential playback of the demo songs,

starting from song 1.

•Pressing a tone group button (ck through cr) while

demo song playback is in progress will switch to the

demo song of that group’s tone. Also, you can scroll

through songs manually with the bt (w, q)

buttons.

Press the 6 (PLAY/STOP) button.

This stops demo song playback.

Playback of the demo songs will continue in an endless

loop until you press the 6 (PLAY/STOP) button to

stop it.

NOTE

•Only the operations described above can be

performed while demo song playback is in progress.

btw, qblUSER SONGS

7PA R T

6PLAY/STOP

2REPEAT

Playing Tone Demo Songs

No. Tone Group Name Tune Name

01 GRAND PIANO

MODERN Original

02 GRAND PIANO

CLASSIC Arabesque 1

03 ELEC PIANO Original

04 VIBES/CLAVI Original

05 ORGAN Original

06 STRINGS/

SYNTH-PAD

Nessun Dorma

[Turandot]

07 BASS/GUITAR Original

08 VARIOUS/GM TONES Original

Song number

Song name

Current measure

Song tempo

English

Playing Demo Songs

E-25

You can import song data from an SD memory card or

computer as a user song, and use it for Auto

Accompaniment or for practice.

Load the song data you want to listen to one

of the Digital Piano’s user songs.

•See “Loading Data from a Memory Card” (page E-47)

and “Connecting to a Computer” (page E-51) for

details about how to load data.

•You also could play back data directly from a

memory card without loading it into Digital Piano

memory. For details, see “Playing Back a Song from a

Memory Card” (page E-48).

Press the bl (USER SONGS) button so its

lamp is lit.

•Each press of the button toggles between the upper

and lower lamps.

Use the bt (w, q) buttons to select the

user song you want.

Example: When user song 003 is selected

Press the 6 (PLAY/STOP) button.

This starts playback of the song.

•Press the 4 (FF) button to perform a fast forward

operation or the 3 (REW) button for rewind.

Pressing and releasing either button moves one

measure, while holding down a button scrolls at high

speed.

•Pressing the 5 (PAUSE) button pauses playback.

Press again to resume song playback.

Press the 6 (PLAY/STOP) button again.

This stops song playback.

•Song playback also will stop automatically when the

end of the song is reached. To configure the Digital

Piano to loop song playback without stopping, turn

on “Song Repeat” (page E-42).

Changing the Song Tempo

You can change the song tempo using the same

procedure that you use to adjust the metronome

tempo. For more information, see “Changing the

Tempo Setting” (page E-14).

Playing on the Keyboard Using the Same

Tone as the Song

Hold down the bl (USER SONGS) button for

at least two seconds.

This will assign the same tone as the right hand part of

the current song to the keyboard.

NOTE

•You can use the procedure under “Practicing Either

Hand’s Part (Part Off)” (page E-26) to turn off the

left hand part and play along on the keyboard using

the left hand part tone.

Listening to Songs Loaded

from an External Source

Lit

User song number Song name

23456

Fast forward

Rewind Pause

Lights with the first beat of each measure

Lights with each subsequent beat of each measure

E-26

Playing Demo Songs

Adjusting the Song Volume

You can use the following procedure to adjust the

volume level of the song’s Auto Accompaniment,

without affecting the volume of keyboard tone output.

For details, see “Song Volume” (page E-41).

Practicing Either Hand’s Part (Part Off)

You can turn off the right hand part*1 or left hand

part*2 of a song and play that part on the Digital Piano

while the song plays back.

Press the 7 (PART) button.

This causes “L-[ON] R-[ON]” to appear on the display.

Use the bt (w, q) buttons to turn off the

part you want.

Press (w) to toggle the left hand part or (q) to toggle

the right hand part on and off.

Press the 7 (PART) button again.

This exits the part on/off screen.

Hold down the bl (USER SONGS) button for

at least two seconds.

This will assign the same tone as the hand that is turned

off to the keyboard.

Press the 6 (PLAY/STOP) button to start

song playback.

The part you turned off does not sound, so you can play

it on the keyboard.

Sounding a Count at the Beginning of a

Song

You can configure the Digital Piano to sound a count

before playback of a song starts, which helps to get the

timing right when you are playing along on the

keyboard. For details, see “Pre-count” (page E-42).

Repeating Playback of a Specific Section

(Repeat)

You can configure the Digital Piano to repeat the

section of a song you want to practice. You could, for

example, specify repeat play from measure 5 to

measure 8.

Press the 6 (PLAY/STOP) button.

This starts playback of the song.

When playback reaches the first measure of

the section you want to repeat, press the 2

(REPEAT) button.

This makes the measure the “start measure”.

The 2 (REPEAT) button lamp flashes at this time.

When playback reaches the last measure of

the section you want to repeat, press the 2

(REPEAT) button again.

This makes the measure the “end measure”.

Repeat playback of the specified section starts as soon

as you select the end measure.

The 2 (REPEAT) button lamp is lit (not flashing) at

this time.

Pressing 2 (REPEAT) again returns to

normal play.

This will cause the 2 (REPEAT) button lamp to go out.

*1 Song data Channel 4 (fixed)

*2 Song data Channel 3 (fixed)

Start End

These measures are repeated.

E-27

English

Music Presets

Music Presets provide you with one-touch tone,

rhythm, chord, and other settings that are optimized

for specific musical genres and songs.

In addition to built-in presets, you can create your own

original Music Presets (user presets).

There are a total of 300 built-in Music Presets, which

are divided into three groups (A, B, C). A fourth group

(D) is provided for user presets.

•For more information, see the “Music Preset List”

(page A-6).

Press bm and bn (MUSIC PRESET) at the

same time.

This causes the 7 (ACCOMP ON/OFF) lamp to flash

and the Music Preset screen to appear.

Use buttons bm to bp (Music Preset group

buttons) to select a group, and then use the

bt (w, q) buttons to select the Music

Preset you want.

This will configure the Digital Piano with settings (tone,

rhythm, etc.) of the selected Music Preset.

The following are the settings that are included in a

Music Preset.

Press the 6 (START/STOP) button to start

Auto Accompaniment with the chord

progression of the Music Preset. Play the

melody on the keyboard.

•The preset chord progression repeats until you stop it

by pressing the 6 (START/STOP) button again.

•Pressing the 7 (ACCOMP ON/OFF) button so the

ACCOMP ON/OFF lamp is lit (not flashing) or unlit

will turn off the chord progression of the Music

Preset and play the normal Auto Accompaniment

pattern.

•Each press of the 7 (ACCOMP ON/OFF) button

cycles in the sequence shown below.

•You can use the following steps to change the rhythm

after selecting a Music Preset.

•To change the tone, use the ck through cr (tone

group) buttons to select the tone group and then use

the bt (w, q) buttons to select a tone number.

To exit a Music Preset, press bm and bn

(MUSIC PRESET) at the same time.

csEXIT

dlENTERbtw/NO, q/YES

3REW

6START/STOP

bmbnMUSIC PRESET

4FF

dki

ctu

bm–bpMusic Preset groups ck–crTone groups

Selecting a Music Preset

Music Preset number Music Preset name

•Tones (main, layer, lower split) (page E-9)

•Layer balance (page E-10)

•Octave shift (page E-12)

•Reverb (page E-13)

•Chorus (page E-13)

•Rhythm (page E-21)

•Tempo (page E-20)

•Auto Harmonize (page E-20)

(1)Hold down the bl (RHYTHM) button until the

displayed Music Preset number and name change to

the rhythm number and name.

(2)Use the bt (w, q) buttons to select the rhythm you

want.

(3)Hold down the bl (RHYTHM) button again until

the rhythm number and name change back to the

Music Preset number and name.

LitUnlit Flashing

Normal Auto Accompaniment Music Preset

chord progression

E-28

Music Presets

A Music Preset editor is provided to allow you to

create your own original Music Presets (user presets).

Up to 50 user presets can be stored in Music Preset

Group D.

Select the Music Preset you want to edit in

order to create your user preset.

Change the tone number, rhythm number,

and other settings of the Music Preset as you

want.

•The settings you configure here will be saved as a

user Music Preset. See step 2 under “Selecting a

Music Preset” (page E-27) for the settings you can

configure and save for a user Music Preset.

Press the bo (BALLAD/PIANO RHYTHMS)

and bp (USER RHYTHMS) buttons at the

same time.

This displays a screen for selecting the type of editing

operation you want to perform.

Edit the Music Preset parameters.

After editing everything you want, press the

cs (EXIT) button.

•This will display a message asking if you want to

save the user preset.

Press the bt (YES) button.

This displays a screen for selecting the Music Preset

number and name for storing the edited data.

•If you do not want to save the edited data, press the

bt (NO) button in place of the bt (YES) button.

Use the bt (w, q) buttons to select the

Music Preset number where you want to

store the edited data.

Creating an Original User

Preset

Editing operation type

4-1.To edit the chord progression

Press the bt (w) down button to display

“CHORD” and then press the dl (ENTER)

button to advance to the chord progression

editing screen.

Next, perform the editing operation described

under “To edit the chord progression” (page

E-29). After you finish the editing operation,

press the cs (EXIT) button to return to the

screen for selecting the type of editing

operation, above.

4-2.To edit Auto Accompaniment parameters

Press the bt (q) up button to display

“Parameter” and then press the dl (ENTER)

button to advance to the Auto

Accompaniment parameter editing screen.

Next, perform the editing operation described

under “To edit Auto Accompaniment

parameters” (page E-31). After you finish the

editing operation, press the cs (EXIT) button

to return to the screen for selecting the type of

editing operation, above.

Music Preset name

Music Preset number for data storage

English

Music Presets

E-29

Enter a name for the preset.

Use the ct (u) and dk (i) buttons to move the cursor

to the character you want to change and then use the bt

(w, q) buttons to change the character. The

following shows a table of available characters.

•To input a space, press both of the bt (w and q)

buttons at the same time.

Press the dl (ENTER) button.

This saves the data.

•If the preset number where you are saving the data

already has data saved to it, a message (Replace?) will

appear on the display to confirm whether you want

to replace the existing data with the new data.

■To edit the chord progression

On the editing operation selection screen

(page E-28), select “CHORD” and then press

the dl (ENTER) button to display the chord

progression editing screen shown below.

(1) Step (timing and chord)

The timing of a chord progression is expressed as a

series of three values separated by colons (such as

001:1:00) indicating measure*1 (001), beat (1), and

tick (00).*2 This series of three values is referred to

collectively as a “step”.

The screen shot above shows the first two steps

(001, 002) of the Music Preset. Use the 3 (REW) and

4 (FF) buttons to scroll and view other steps.

*1 Up to 999 measures

*2 There are 12 ticks per beat, as shown below.

(2) Cursor

Specifies the step that is currently selected for

editing.

(3) Resolution

Resolution is a unit used when editing step timing.

The initial resolution is R1 (one measure), but you

also can select R4 (1 beat = 4 quarter notes) when

you want to specify chords for each beat. Use the

instrument part buttons (ck through cr) to select

one of the eight resolutions shown below.

(3) Resolution(2) Cursor (1) Step (timing and chord)

01 02 09 10 1100

Chord progression

Measure 1

Beat 1 Beat 2 Beat 3 Beat 4 Beat 1 Beat 2

Tick

001:1:00

002:1:00

For the sample display

above, the chord change

from C to Bm occurs here.

Measure 2

3 3

R1 R2 R4 R8 R8T R16 R16T R32T

ck cl cm cn co cp cq cr

(1 measure) (2 beats) (1 beat) (1/2 beat) (1/3 beat) (1/4 beat) (1/6 beat) (1/8 beat)

E-30

Music Presets

Use the 3 (REW) and 4 (FF) buttons to

move the cursor (2) on the chord progression

editing screen to the step you want to select.

Change the content of the selected step as

desired.

Repeat the above steps to edit all of the steps

you want.

•You can playback the Music Preset you are currently

editing by pressing the 6 (START/STOP) button.

•The table below describes other Music Preset editing

operations you can perform. Press the bs

(FUNCTION) button, use the ct (u) and dk (i)

buttons to select the editing operation you want,

perform the required operation, and then press the dl

(ENTER) button to apply the edit and return to the

chord progression editing screen.

•To exit the editing operation and discard all of your

edits, press the cs (EXIT) button.

*The Music Presets in groups B, C, and D are

numbered sequentially, following the numbers in

group A, which start with 001. For details about

sequential numbers, see the “Music Preset List” on

page A-6.

After all editing operations are complete,

press the cs (EXIT) button to return to the

editing operation selection screen (page

E-28).

NOTE

•A single preset can contain up to approximately

2,000 chords. If your edits cause the chord limit to be

exceeded, the message “Memory Full” will appear

on the display and further editing will become

impossible.

3-1.Select a chord fingering mode and use the

chord keyboard (page E-19) to input chords.

Fingering a chord causes the cursor (2) to

move to the next step automatically.

•If you want to advance to the next step

without changing the current chord, press

the 5 (PAUSE) button.

•If (3) Resolution is shorter than the time up

to the next step, a new step (without chord)

that is equal to the time of the resolution

will be inserted temporarily into the Music

Preset. Fingering a chord for the new step

will cause the step to be registered as part

of the Music Preset, and the cursor will

advance to the next step.* You can use this

operation to insert a new step between the

current and following step.

*Using the 3 (REW) and 4 (FF) buttons to

move the cursor without inputting a chord

will delete the temporarily inserted step.

3-2.Use the bt (w, q) buttons to change the

step timing (measure:beat:tick).

Each press of either button changing the

timing in accordance with the resolution.

•The range of values you can specify for the

step timing is limited by the steps before

and after the current step.

•The timing of the first step (001:1:00) is

fixed and cannot be changed. Also, the final

step is always one measure, regardless of

the resolution.

3-3.To delete a step, press both of the bt (w and

q) buttons at the same time.

•You cannot delete the first step or the last

step.

Last step

Editing

Operation

(Display)

Description Operation

1Initialize

(Initialize)

Initializes all steps.

Initialization is useful

when you want to create

a totally new chord

progression from

scratch.

–

Change Key

(Change

Key)

Changes the pitch (key)

of the chords in all of the

steps in semitone units.

Use the bt (w, q)

buttons to select the

amount of change

you want (–5 to 6

semitones).

Append

Music Preset

(Append

Chords)

Copies all of the steps of

another Music Preset to

the end of the current

Music Preset.

Use the bt (w, q)

buttons to select the

number∗ of the

Music Preset you

want to add.

Delete

Measures

(DELETE

Measure)

Deletes a specified

number of measures

from the current cursor

step forward.

Use the bt (w, q)

buttons to select the

measures.

Insert

Measure

(INSERT

1Measure)

Inserts a blank measure

at the currently selected

step. –

Music Presets

E-31

English

■To edit Auto Accompaniment parameters

On the editing operation selection screen (page E-28), select “Parameter” and then press the dl

(ENTER) button to display the Auto Accompaniment parameter editing screen shown below.

Use the ct (u) and dk (i) buttons to select a parameter, and the bt (w, q) buttons to change its

setting.

After all editing operations are complete, press the cs (EXIT) button to return to the editing operation

selection screen (page E-28).

Parameter Description Setting

1SYNCHRO TYPE:

Synchro type

Selects the synchro standby status and type

when the Music Preset is selected.

0 Off: Off (no standby)

1 Normal: From standby to normal pattern

2 Variation: From standby to variation pattern

3 Intro: From standby to intro pattern

2DRUM ON/OFF:

Drum on/off Toggles the drum part (page E-22) on or off. OFF: Mutes the part.

ON: Sounds the part.

3PERC ON/OFF:

Percussion on/off

Toggles the percussion part (page E-22) on or

off.

OFF: Mutes the part.

ON: Sounds the part.

4BASS ON/OFF:

Bass on/off Toggles the bass part (page E-22) on or off. OFF: Mutes the part.

ON: Sounds the part.

5 - 9

CHORD1 - 5

ON/OFF:

Chord 1 - 5 on/off

Toggles the Chord 1 through 5 parts (page

E-22) on or off.

OFF: Mutes the parts.

ON: Sounds the parts.

10 INTRO CHORD:

Intro chord

Selects from among major (× 12 keys) and

minor (× 12 keys) for the intro chords.

C - B: Major (C to B)

Cm - Bm: Minor (Cm to Bm)

11 ENDING CHORD:

Ending chord

Selects from among major (× 12 keys) and

minor (× 12 keys) for the ending chords.

C - B: Major (C to B)

Cm - Bm: Minor (Cm to Bm)

12 AUTO FILL-IN:

Auto fill in on/off

Specifies whether or not a fill-in should be

inserted into the final measure of a chord

progression.

OFF: Fill-in not inserted

ON: Fill in inserted

TIMING SET:

Chord progression

variation

• This parameter lets you add different

variations to the timing of the chord

progression being edited. You can use it to

match the chord progression to the beat of a

specific rhythm.

• A chord (step) that is outside of the rhythm’s

beat is cut off.

1 Normal: Edited chord progression proceeds

as-is.

2 Half: Halves chord timing within a measure.

3 Double: Doubles chord timing within a

measure.

4 3/4: Multiplies chord timing within a measure

by 3/4. Select this setting to match to a

6/8 time rhythm.

5 6/4: Multiplies chord timing within a measure

by 3/2. Select this setting to match to a

6/4 time rhythm.

Setting Parameter

E-32

Registering Tone and Rhythm Setups

Registrations let you save Digital Piano setups (tone,

rhythm, tempo, etc.) and for quick and easy recall

when you need them.

Registrations are stored using eight banks of 12 areas

each as shown in the illustration below, for a total of 96

setups. Areas A through D on the left (tone and

accompaniment area) is for storing tones and Auto

Accompaniment settings, while areas 1 through 8 (tone

areas) are for storing tone settings only.

■Registration Data Types

zTone Settings

•Tone numbers (main, layer, lower split)

•Layer on/off

•Layer balance

•Split on/off

•Split point

•Octave shift

•Brightness

•Reverb

•Chorus

•Transpose

•Touch response

•Soft/sostenuto pedal setting

•Damper pedal adjustment

•Pitch bend range

zAuto Accompaniment Settings (Areas A through D

only)

•Rhythm number

•Accomp on/off

•Chord fingering mode

•Synchro standby

•Tempo

•Auto Accompaniment volume

•Auto harmonize

brREGISTRATION

btw, q

dmSTORE

bm–bpTone and accompaniment areas

ck–crTone areas

ABCD 12345678

Bank 7, Area B data Bank 3, Area 2 data

Tone Settings

Keyboard Tone:

003 Harpsichord

Brightness: 2

Reverb: 1 Room

Chorus: Off

Auto Accompaniment

Settings

Rhythm: 005 Pop Rock

Tempo: 180

Accompaniment Volume:

098

Tone Settings

Keyboard Tone:

002 Electric Piano2

Brightness: –1

Reverb: 4 Stadium

Chorus: 1 LightChorus

Tone and

accompaniment area Tone area

Banks

English

Registering Tone and Rhythm Setups

E-33

Configure the Digital Piano with the tone,

rhythm, and other settings you want to save.

While holding down the dm (STORE) button,

use the bt (w, q) buttons to select the bank

where you want to save the registration.

Example: Bank 4

Next, hold down the dm (STORE) button

again as you use the rhythm group buttons

(bm through bp) or instrument part buttons (ck

through cr) to select an area.

The data will be saved to the bank and area you specify.

Example: Bank 4, Area C

Press the br (REGISTRATION) button so its

lower lamp is lit.

This enters the registration recall mode.

Use the bt (w, q) buttons to select the

bank where the registration you want to recall

is located.

Use the rhythm group buttons (bm through bp)

or instrument part buttons (ck through cr) to

specify the area.

This will configure the Digital Piano with the

registration data located at the bank and area you

specified.

Example: When recalling the registration data in Bank

4, Area C

Saving Registration Data

bm bn bo bp

ck cl cm cn co cp cq cr dm

Tone and

accompaniment area

Tone area

Area

Recalling a Registration

Lit

E-34

Recording Your Keyboard Play

You can record your music as you play and store up to

five songs in Digital Piano memory for later playback.

You can divide a song into parts (by instrument, by left

hand and right hand, etc.) and record each part

separately. You can even use “punch-in recording” to

edit specific parts of existing recordings.

The following are the steps for recording or playing

back a single recorder memory song.

Press the 9 (RECORDER) button twice so

its lamp is flashing.

This turns on the recorder and enters record mode.

•Each press of the 9 (RECORDER) button cycles

through modes as shown below.

Configure the tone, rhythm, and other

settings you want to use.

•The settings you configure here will be included as

part of the recorded song data.

•For details about what is included in the recorded

song data, see “System Track” (page E-35).

Play something on the keyboard.

Recording starts as soon as you play something.

•If Auto Accompaniment is playing, it will be

included in the recorded data.

When you are finished, press the 6 (START/

STOP) button.

This will cause the 9 (RECORDER) lamp to flash and

then light, indicating the playback mode.

•If you are using Auto Accompaniment, you also can

end the recording session by pressing the 5

(ENDING) button.

To play back what you have recorded, press

6 (START/STOP) again.

•Each press of 6 starts and stops playback.

To turn off the recorder, press the

(

RECORDER

) button so its lamp goes o

ut.

NOTE

•Recorder memory capacity is approximately 10,000

notes per song. When remaining capacity is 100

notes or less, the 9 (RECORDER) button lamp will

flash at high speed. Recording will stop

automatically when memory becomes full.

•Repeat, fast reverse, fast forward, pause, and tempo

adjustment during playback are the same as when

playing back user songs. See “Listening to Songs

Loaded from an External Source” (page E-25) for

more information.

•You can listen to the song data currently stored in

recorder memory at any time by pressing the

9 (RECORDER) button to enter the playback mode

and then pressing 6 (START/STOP).

dki

ctubsFUNCTION

btw/NO, q/YES

6START/STOP

9RECORDER

Recording or Playing Back a

Single Song

Recorder Off Recorder On

Unlit Lit: Playback mode Flashing: Record mode

Lit: Playback mode

Unlit: Recorder off

English

Recording Your Keyboard Play

E-35

IMPORTANT!

• A new recording replaces (deletes) previously

recorded contents.

• If power to the Digital Piano is cut off while recording

is in progress, everything you recorded up to that

point will be deleted. Take care so power is not

turned off accidentally during recording operations.

You can record up to five songs (numbered 1 through

5) in memory. After that, you can select a specific song

for playback.

Use the 9 (RECORDER) button to cycle

through the recorder modes until the

playback mode is selected.

While holding down the bs (FUNCTION)

button, press the 9 (RECORDER) button.

This displays the song selection screen.

Use the bt (w, q) buttons to select the

song number you want.

Press the cs (EXIT) button to exit the song

selection screen.

To record to the currently selected song,

press the 9 (RECORDER) button. To play

back the currently selected song, press the

6 (START/STOP) button.

If you are recording, continue from step 2

under “Recording or Playing Back a Single

Song” (page E-34).

You can record specific instruments, the left hand and

right hand, or other parts of a song individually, and

then combine them into a final song.

■What is a track?

A “track” is a separate recorded part of a song. The

recorder of this Digital Piano supports a total of 17

tracks, which are divided between two types described

below.

zSystem Track

In addition to notes you play on the keyboard and

other performance operation data, the system track

also includes a wide range of setup information for

the song, including layer on/off, split on/off, tempo,

Auto Accompaniment settings, reverb on/off, etc.

When you record a single-track song to recorder

memory, as shown under “Recording or Playing

Back a Single Song” (page E-34) and “Recording or

Playing Back Multiple Songs” (page E-35),

everything is recorded to the system track.

zTracks 01 through 16

These tracks can be used to record notes, as well as

pitch bend wheel and pedal operations, and the

keyboard tone setting. These tracks can be combined

with the system track and each other to create the

final song.

Recording or Playing Back

Multiple Songs

Lit: Playback mode

Recording to a Specific Track

(Part)

E-36

Recording Your Keyboard Play

■Supported Track Data

The following describes the data that can be recorded

to each type of track.

System Track, Tracks 01 through 16

Keyboard notes, keyboard tone setting (main), pedal

and pitch bend wheel operation

System Track only

Layer, split, octave shift, reverb, chorus, keyboard

temperament, tempo, Auto Accompaniment play, auto

harmonize, one-touch preset, Music Preset,*1

registration*1*2

Record the first part to the system track.

•Use the procedure under “Recording or Playing Back

a Single Song” (page E-34) or “Recording or Playing

Back Multiple Songs” (page E-35) to record to the

system track.

Use the 9 (RECORDER) button to cycle

through the recorder modes until the

RECORDER lamp is flashing (record mode).

While holding down the bs (FUNCTION)

button, press the 9 (RECORDER) button.

This displays the track selection screen.

Use the bt (w, q) button to select the track you

want to record next (T01 through T16).

After selecting a track, press the cs (EXIT) button to

exit the track selection screen.

Select the tone of the part you want to record

to the track.

Press the 6 (START/STOP) button.

This will start playback of what you recorded to the

system track and start recording to the currently

selected track. Play what you want to record to the

current track along with the playback from the system

track.

To stop recording, press the 6 (START/

STOP) button again.

This enters the playback mode. Press the 6 (START/

STOP) button again to play back the track you just

recorded. Each press of 6 (START/STOP) starts and

stops playback.

•You can use the following procedure to turn specific

tracks on (play enabled) and off (play disabled). This

allows you to listen only to the track(s) you want

when recording a new track.

Repeat steps 2 through 6 as required to

record all of the tracks you want.

*1 Recall only

*2 The Auto Accompaniment volume level and

transpose setting of the recalled data is not included

in the recording.

Track Name Display

System Track Sys

Tracks 01 through 16 T01 through T16

Flashing: Record mode

(1) While holding down the bs (FUNCTION)

button, press the 9 (RECORDER) button.

This displays the song selection screen.

(2) Press the dk (i) button once.

This displays the track on/off screen.

(3) Use the bt (w, q) buttons to select the track

you want, and then press the dl (ENTER) button

to toggle it on or off.

English

Recording Your Keyboard Play

E-37

You can use the procedures below to delete an entire

recorder song or to delete a specific track of a recorder

song.

Deleting a Recorder Song

Use the 9 (RECORDER) button to cycle

through the recorder modes until the

RECORDER lamp is lit (playback mode).

While holding down the bs (FUNCTION)

button, press the 9 (RECORDER) button.

This displays the recorder song selection screen.

Use the bt (w, q) buttons to select the

recorder song you want to delete.

Hold down the 9 (RECORDER) button until

the message “Sure?” appears on the display.

Press the bt (YES) button to delete the

recorder song.

•To cancel the delete operation, press the bt (NO)

button.

Deleting a Recorder Song Track

Perform steps 1 through 3 of the procedure

under “Deleting a Recorder Song” to select

the recorder song that contains the track you

want to delete.

Press the dk (i) button.

This displays the track selection screen.

Use the bt (w, q) buttons to select the

track you want to delete.

Hold down the 9 (RECORDER) button until

the message “Sure?” appears on the display.

Press the bt (YES) button to delete the track.

•To cancel the delete operation, press the bt (NO)

button.

You can use punch-in recording to re-record a specific

part of recorder song that you want to improve or

correct.

Turn on the recorder, enter the record mode,

and select the track that contains the section

you want to re-record.

•See step 3 under “Recording to a Specific Track

(Part)” (page E-35).

Hold down the 9 (RECORDER) button until

the punch-in recording screen appears on the

display.

Press the 6 (START/STOP) button.

This will start playback of the selected track.

When playback reaches the point you want to

re-record, play the notes and perform the

other operations you want.

This automatically starts punch-in recording, which

will continue until step 5, below.

•Any one of the following also will start punch-in

recording: a pedal or pitch bend wheel operation;

pressing the 9 (RECORDER) button;*1 changing the

tone setting; changing the rhythm, or tempo setting*2

•You can perform 3 (REW), 4 (FF), and 5 (PAUSE)

button operations during punch-in playback to jump

more quickly to the section you want to re-record.

Deleting Recorder Data

Lit: Playback mode

Re-recording Part of a

Recorder Song

(Punch-in Recording)

*1 Press 9 (RECORDER) when you want to start

punch-in recording without note input or a setting

change.

*2 System track only

Mistake

Playback

Use punch-in

recording to re-record

only this part.

E-38

Recording Your Keyboard Play

To stop punch-in recording, press the 6

(START/STOP) button again.

Anything in the track following the point where you

pressed the 6 (START/STOP) button will be retained

as-is.

•If you want to delete all of the data in the track

following the section you re-recorded with punch-in

recording, press the 9 (RECORDER) button in place

of the 6 (START/STOP) button above.

•If you want to cancel punch-in recording and retain

the original (unedited) track data, hold down the 9

(RECORDER) button until the display exits the

punch-in recording screen.

Specifying the Punch-in Recording

Location (Auto Punch-in Recording)

You can use the following procedure to specify a

particular range for punch-in recording.

Turn on the recorder, enter the record mode,

and display the recording setup screen.

•While holding down the bs (FUNCTION) button,

press the 9 (RECORDER) button.

Use the

(

) and

(

) buttons to display

“AutoPu.IN”, and then use the

(

)

buttons to select the start measure.

Use the ct (u) and dk (i) buttons to

display “AutoPu.OUT”, and then use the bt

(w, q) buttons to select the end measure.

•After selecting the start and end measures, press the

cs (EXIT) button to exit the recording setup screen.

Select the track that contains the range of

measures you want to re-record.

•See step 3 under “Recording to a Specific Track

(Part)” (page E-35).

Hold down the 9 (RECORDER) button until

the punch-in recording screen appears on the

display.

Press the bt (q) button to turn on auto

punch-in recording.

Press the 6 (START/STOP) button to start

playback.

•Punch in recording will start from the start measure

and stop with the end measure automatically.

Play the notes and perform the other

operations you want.

Start measure End measure

Punch-in recording range

English

Recording Your Keyboard Play

E-39

■Performing Punch-in Recording for Areas

Smaller than One Measure

Use the procedure below to specify a punch-in

recording area that includes a part of a measure.

Example: To re-record from beat 3 of measure 2 up to beat

1 of measure 4

Start playback of the song that contains the

section you want to re-record.

When playback reaches the beginning of the

section you want to re-record, press the 2

(REPEAT) button.

When playback reaches the end of the

section you want to re-record, press the 2

(REPEAT) button again.

Press the 6 (START/STOP) button to stop

playback.

Turn on the recorder and select the track that

contains the section you want to re-record.

•For information about selecting a track, see step 3

under “Recording to a Specific Track (Part)” (page

E-35).

Hold down the 9 (RECORDER) button until

the punch-in recording screen appears on the

display.

Press the bt (q) button to turn on auto

punch-in recording.

Press the 2 (REPEAT) button to turn on

repeat.

Press the 6 (START/STOP) button.

This starts punch-in playback from the measure before

the location (start point) you specified in step 2, above.

•Punch-in recording starts automatically when

playback reaches the start point and ends

automatically when it reaches the location you

specified in step 3 (end point).

To re-record this section

E-40

Other Settings

You can use the settings in this section to adjust the

tuning and touch of the keyboard, to configure pedal

and MIDI settings, and to configure other parameters

in order to tailor Digital Piano operation to your

particular needs.

Press the bs (FUNCTION) button.

The FUNCTION lamp will light and the function screen

will appear on the display. (See table below.)

Use the ct (u) and dk (i) buttons to select

one of the parameters (1 through 8) shown in

the table below.

•Parameters 4 through 8 actually are parameter

groups. After selecting a group, press the dl

(ENTER) button, and then use buttons ct (u) and dk

(i) to select the parameter you want.

•Short cut buttons also are available for accessing a

parameter directly after you press the bs

(FUNCTION) button, without going through the

menu. See the “Shortcut Button” column in the table

below for the applicable shortcut button of each

parameter.

Use the bt (w, q) buttons to change the

setting of the currently selected parameter.

•To return to the function screen, press the cs (EXIT)

or bs (FUNCTION) button.

NOTE

•Holding down the bs (FUNCTION) button while

you press the bt (w, q) buttons in step 3 will

scroll the setting in steps of 10.

•You also can use the bs (FUNCTION) button for

faster scrolling while changing the tone number,

rhythm number, and other scrollable settings.

•Keep the bs (FUNCTION) button depressed

while pressing a bt (w, q) button for high-

speed scrolling. Releasing the bs (FUNCTION)

button first can result in another unintended

setting being changed.

dki

ctubsFUNCTION

btw, q

Configuring Settings

Parameter or group Setting

Other Settings

E-41

English

No.

Parameter Display

Name Description Settings Shortcut

Button*

1 Keyboard Key (Transpose) Transpose Adjusts keyboard tuning by semitone

units.

–12 to 00 to 12

semitones ck

2 Keyboard Fine Tuning

(Tuning)

Tune Adjusts keyboard tuning by cent

(1 semitone = 100 cents) units.

–99 to 00 to 99 cents cl

3 Keyboard Touch (Touch

Response)

Touch Adjusts keyboard touch. Off: Off

1: Strong sound even

with light pressure

2: Normal

3: Normal sound even

with strong pressure

4Volume Level Group Volume co

4-1 Layered Tone Volume

(Layer Balance)

LayerBal. Adjusts the volume level of the layered

tone without changing the keyboard

main tone.

–24 to 00 to 24

–

4-2 Auto Accompaniment

Volume

AccompVol. Adjusts the volume level of Auto

Accompaniment without changing the

keyboard tone volume level.

00 to 42

bs – bl

4-3 Song Volume SongVol. Adjusts the volume level of user song

playback without changing the

keyboard tone volume level.

00 to 42

bs – bl

4-4 Metronome Volume MetroVol. See page E-15. 00 to 42 bs – 8

Temperament/Effect Group

Tmpr/Effect cp

5-1 Temperament Temper. Changes the temperament of the

keyboard and Auto Accompaniment

from the standard equal temperament

to another tuning more suitable for

playing classics, etc.

• Pressing a keyboard key while the

temperament screen is displayed

will make the pressed key the base

note of the temperament.

00: Equal / 01: Pure Major /

02: Pure Minor /

03: Pythagorean /

04: Kirnberger 3 /

05: Werckmeister /

06: Mean-Tone / 07: Rast /

08: Bayati / 09: Hijaz /

10: Saba / 11: Dashti /

12: Chahargah /

13: Segah / 14: Gurjari

Todi / 15: Chandrakauns /

16: Charukeshi

C to B (12 types)

–

5-2 Accompaniment

Temperament

AccompTmpr Turn this setting off to play Auto

Accompaniment patterns using

standard equal temperament (00:

Equal), regardless of the temperament

setting currently selected with the

Temperament parameter (5-1).

Off, On

–

5-3 Stretch Tuning Stretch Sharpens high notes and flattens low

notes to achieve stretch tuning. Turn

off this setting to play with normal

(non-stretch) tuning.

Off, On

–

5-4 Brilliance Brilliance See page E-12. –3 to 0 to 3 –

5-5 Acoustic Resonance AcoResona. Reproduces the acoustic resonance

that occurs when the damper pedal is

depressed on a grand piano.

No acoustic resonance is applied when

this setting is turned off.

Off, On

–

5-6 Octave Shift OctShift See page E-12. U1 : –2 to 0 to 2

U2 : –2 to 0 to 2

L1 : –2 to 0 to 2

bs – br

5-7 Duet Mode Duet See page E-15. Off, On bs – dk

*bs – bl in this column means, “While holding down bs, press bl.”

E-42

Other Settings

6Song Playback/Card Group Play/CARD cq

6-1 Pre-count PreCount Turn on this setting for an audible

count before starting playback of a

user song or a song on a memory card.

Off, On

–

6-2 Song Repeat SongRepeat Turn on this setting to repeat play a

user song or a song on a memory card.

Off, On bs – 2

6-3 Card Folder CARD Folder See page E-53. (Folder Name) bs – bn

to bp

6-4 Formatting a Memory

Card

CARD

FORMAT

See page E-45. – bs – dl

6-5 Card File Delete File DELETE See page E-47. – –

6-6 Card File Rename File RENAME See page E-48. – –

7MIDI Group MIDI cr

7-1 Keyboard Channel KeyboardCh Selects the keyboard channel, which is

the channel used to send MIDI data

corresponding to Digital Piano

keyboard play to an external device.

01 to 16

–

7-2 Accomp MIDI Out AccompOut Turn on this setting to send MIDI data

corresponding to Auto

Accompaniment to an external device.

Off, On

–

7-3 MIDI In Chord Judge ChordJudge Select whether chord input should be

performed when an Auto

Accompaniment chord keyboard MIDI

note on message is received.

Off, On

–

7-4 Local Control LocalCtl. Turn off this setting to have keyboard

notes sent to an external device

without being sounded by the Digital

Piano.

Off, On

–

No.

Parameter Display

Name Description Settings Shortcut

Button*

*bs – bl in this column means, “While holding down bs, press bl.”

Other Settings

E-43

English

No.

Parameter Display

Name Description Settings Shortcut

Button*

8Other Parameters Group General cs

8-1 Display Contrast Contrast Adjusts the contrast of the Digital

Piano’s display.

00 to 16 –

8-2 Soft/Sostenuto Pedal

Jack Setting

Ped.Assign Specifies whether the pedal unit

connected to the SOFT/SOSTENUTO

jack is a soft pedal or a sostenuto

pedal.

• See page E-15 for details about the

two pedal types.

SFT : Soft pedal

SOS : Sostenuto pedal

–

8-3 Half Pedal Effect HalfPedal Adjusts the amount of the pedal effect

applied when the damper pedal is

pressed part way.

00 to 42

–

8-4 Pitch Bend Range BendRange Specifies the amount of pitch bend

applied when the pitch bend wheel is

rotated all the way up or down.

00 to 12 semitones

–

8-5 Panel Lock PanelLock Turn on to lock the Digital Piano’s

control panel to prevent unauthorized

or accidental operation.

• This setting is disabled in the Duet

Mode, while the recorder is on, or

while Auto Accompaniment, a song,

or the metronome is playing.

Off, On

–

8-6 Setting Backup BackUp Switching this setting from off to on

will save various Digital Piano settings

in effect at that time, and restore them

the next time the Digital Piano is

turned on.

• This operation is disabled in the

Duet Mode, while the recorder is on,

or while Auto Accompaniment, a

song, or the metronome is playing.

Off, On

–

*bs – bl in this column means, “While holding down bs, press bl.”

E-44

Using a Memory Card

You can use the procedures in this section to transfer

edited Auto Accompaniment data, recorder data, and

other data from the Digital Piano to a commercially

available SD memory card for storage. You also can use

a memory card to transfer standard MIDI files (SMF),

and accompaniment data you downloaded from the

CASIO website from your computer to Digital Piano

memory. Once you do, you can use them as user songs

and user rhythms.

zUse a memory card with a capacity of 2GB or less.

Use of a card with a capacity that is greater than

2GB or other types of memory cards is not

supported.

zIn this manual, mentions of a “memory card” refer

to an SD memory card.

■Types of Data

*Can be saved as a standard MIDI file (SMF format 0).

Card and Card Slot Precautions

IMPORTANT!

• Be sure to observe the precautions provided in the

documentation that comes with the memory card.

• Memory cards have a write-protect switch. Use it

when you want to protect the data on the card from

accidental deletion.

• Avoid using a memory card under the following

conditions. Such conditions can corrupt data stored

on the memory card.

• Areas subjected to high temperature, high

humidity, or corrosive gas

• Areas subjected to strong electrostatic charge and

digital noise

• Never touch the contacts of a memory card when

loading it or removing it from the Digital Piano.

• Never eject the memory card while data is being

written to or loaded from it. Doing so can corrupt the

data on the memory card and damage the memory

card slot.

• Never insert anything besides a memory card into

the card slot. Doing so creates the risk of

malfunction.

• Electrostatic charge from your fingers or the memory

card to the card slot can cause malfunction of the

Digital Piano. If this happens, turn the Digital Piano

off and then back on again.

A memory card can become quite warm after very

long use in the memory card slot. This is normal and

does not indicate malfunction.

bsFUNCTION dlCARD/INTERNAL,

ENTER

btw/NO, q/YES

dki

6PLAY/STOP

ctu

7PA R T bm–bpFolders

Data Type Description

(File Name Extension)

Supported

Operations

Save to

Memory

Card

Load

from

Memory

Card

User

rhythms

(page E-21)

Auto Accompaniment

data edited with this

Digital Piano (AC7)

User songs

(page E-25)

One of the following two

types of music data

1. CASIO format data

(CM2)

2. Standard MIDI files

(MID)

SMF Format 0 or

Format 1

–O

User Music

Presets

(page E-28)

Music Preset data edited

on this Digital Piano

(MPS)

Recorder

songs

(page E-34)

Song data recorded on

this Digital Piano (CSR) O*O

Registration

(page E-32)

Tone and rhythm setup

settings (CR6) OO

English

Using a Memory Card

E-45

IMPORTANT!

• A memory card must be positioned correctly when

being loaded into the Digital Piano. Trying to force

an improperly oriented memory card into the slot can

damage the memory card and the slot.

With the top of the memory card facing

upwards (so you can see it), carefully insert it

into the Digital Piano’s memory card slot (dn)

until stops with a click.

To remove the memory card first press it into

the slot further.

This will cause the memory card to disengage and eject

partially. Pull the memory card the rest of the way out

of the slot.

IMPORTANT!

• Format a memory card before using it for the first

time.

• Before formatting a memory card, make sure it does

not have any valuable data stored on it.

• The memory card format operation performed by this

Digital Piano is a “quick format”. If you want to

completely delete all of the data on the memory

card, format it on your computer or some other

device.

Insert the memory card you want to format

into the Digital Piano’s memory card slot.

Make sure the write-protect switch of the memory card

is not in the write-protect position so writing is enabled.

While holding down the bs (FUNCTION)

button, press the dl (CARD/INTERNAL)

button.

This displays the format screen.

Press the dl (ENTER) button.

This will display a confirmation message (SURE?).

•If you want to cancel the format operation, press the

bt (NO) or cs (EXIT) button.

Press the bt (YES) button.

•The message “Please Wait” will remain on the

display while the format operation is being

performed. Do not perform any Digital Piano

operation while this message is on the display.

“Complete” appears on the display after formatting

is complete.

Loading and Removing a

Memory Card

Top

Formatting a Memory Card

E-46

Using a Memory Card

Use the following procedure to save Digital Piano data

to a memory card.

•Recorder songs can be saved as a standard MIDI file

(SMF format 0).

•User songs (downloaded songs, etc.) cannot be

saved to a memory card.

Insert a memory card into the Digital Piano’s

memory card slot.

Select the data you want to save to the

memory card.

Hold down the dl (CARD/INTERNAL) button

until the “LOAD” screen appears for the data

you selected.

•You can cancel the LOAD/SAVE operation any time

by pressing the cs (EXIT) button.

Press the dk (i) button to switch to the

“SAVE” screen for the data you selected.

•If you are saving a recorder song to a standard MIDI

file (SMF), press the dk (i) button again so “SMF” is

displayed on the right side of the screen.

Use the bt (w, q) buttons to select the file

number (01 to 99) you want to assign to the

data when it is saved to the memory card.

•The file number is the final two characters of the file

name* that appears on the display. By changing this

within the range of 01 to 99 for each save, up to 99

files of the same data type can be stored on the

memory card.

*The first six characters of the file name indicate the

data type as shown below. These characters are

fixed and cannot be changed.

Press the dl (ENTER) button.

•The message “Please Wait” will remain on the

display while the save operation is being performed.

Do not perform any Digital Piano operation while

this message is on the display. “Complete” appears

on the display after data save is complete.

•If there already is a file with the same name on the

memory card, a message (Replace?) will appear

asking if you want to replace it with the new data.

Press the bt (YES) button to overwrite or the bt (NO)

button to cancel the save operation.

■Memory Card Data Storage

The above procedure stores Digital Piano data in a

folder named MUSICDAT on the memory card.

•The MUSICDAT folder is created automatically

when you format the memory card on the Digital

Piano (page E-45).

•Note that files not in the MUSICDAT folder cannot

be loaded, deleted, or renamed by this Digital Piano.

You also will not be able to load or delete any file

stored in any subfolder inside the MUSICDAT

folder.

Saving Digital Piano Data to a

Memory Card

To select this

type of data:*1Do this:

User rhythms Select from among user rhythms 001

through 010 (page E-21).

User Music

Preset

Select from among user Music Preset

001 through 050 (page E-28).

Recorder songs Select from among recorder songs 1

through 5 (page E-34).

Registrations*2Press the br (REGISTRATION) button

so its lower lamp is lit.

*1 For more information about data types, see page

E-44.

*2 All registration data (8 banks × 12 areas) is saved

in a single file.

Data Type File Name

(** = file number)

User rhythms USRRHY**

User Music Preset USRMPS**

Recorder songs RECSNG**

Registrations REGIST**

English

Using a Memory Card

E-47

You can use the procedure below to load data from a

memory card into Digital Piano memory.

IMPORTANT!

• Make sure that all of the data you want to load is in

the MUSICDAT folder on the memory card.

Note that if you put data into a music data play-only

folder on a memory card (such as the MUSIC__B

folder), you will no longer be able to load that file into

Digital Piano memory.

Insert the memory card into the Digital

Piano’s memory card slot.

Select the data you want to load.

*For more information about data types, see page

E-44.

Hold down the dl (CARD/INTERNAL) button

until the “LOAD” screen appears for the data

you selected.

•You can cancel the LOAD/SAVE operation any time

by pressing the cs (EXIT) button.

Use the bt (w, q) buttons to select the file

you want.

Press the dl (ENTER) button.

•The message “Please Wait” will remain on the

display while the load operation is being performed.

Do not perform any Digital Piano operation while

this message is on the display. “Complete” appears

on the display after data loading is complete.

•If there already is a file with the same name on the in

Digital Piano memory, a message (Replace?) will

appear asking if you want to replace it with the new

data. Press the bt (YES) button to overwrite or the bt

(NO) button to cancel the load operation.

Use the following procedure to delete memory card

data (files).

Insert the memory card into the Digital

Piano’s memory card slot.

While holding down the bs (FUNCTION)

button, press the dl (CARD/INTERNAL)

button.

This displays the memory card format screen (page

E-45).

Press the dk (i) button.

This displays the file delete screen.

Press the dl (ENTER) button.

This displays a screen for selecting data for deletion.

Use the bt (w, q) buttons to select the file

you want.

Press the dl (ENTER) button.

This will display a confirmation message (SURE?).

•If you want to cancel the delete operation, press the

bt (NO) or cs (EXIT) button.

Press the bt (YES) button.

•The message “Please Wait” will remain on the

display while the delete operation is being

performed. Do not perform any Digital Piano

operation while this message is on the display.

“Complete” appears on the display after deletion is

complete.

Loading Data from a Memory

Card

To load this

type of data*Do this:

User rhythms Select from among user rhythms 001

through 010 (page E-21).

User songs Select from among user songs 001

through 010 (page E-25).

User Music

Preset

Select from among user Music Presets

001 through 050 (page E-28).

Recorder songs Select from among recorder songs 1

through 5 (page E-34).

Registrations Press the br (REGISTRATION) button

so its lower lamp is lit.

Deleting Memory Card Data

E-48

Using a Memory Card

Use the following procedure to change the file name of

a file on a memory card.

Insert the memory card into the Digital

Piano’s memory card slot.

While holding down the bs (FUNCTION)

button, press the dl (CARD/INTERNAL)

button.

This displays the memory card format screen (page

E-45).

Press the dk button (i) twice so “File

RENAME” is displayed.

Press the dl (ENTER) button.

This displays a screen for changing the file name.

Use the bt (w, q) buttons to select the file

you want.

Use the dk (i) and ct (u) buttons to move

the flashing cursor to the character you want

to change, and then use the bt (w, q)

buttons to change the character.

•The characters you can select are shown below.

After the file name is the way you want, press

the dk (ENTER) button.

This will display a confirmation message (SURE?).

•If you want to cancel the renaming operation, press

the bt (NO) or cs (EXIT) button.

Press the bt (YES) button.

•The message “Please Wait” will remain on the

display while the rename operation is being

performed. Do not perform any Digital Piano

operation while this message is on the display.

“Complete” appears on the display after renaming is

complete.

You can use the procedure below to play back a user

song (page E-25) stored on a memory card without

loading the song into Digital Piano memory.

■Memory Card Folders

Formatting a memory card on the Digital Piano will

automatically create the four folders shown below. You

put playback song data into any one of the folders. You

can use the four folders to group your music data by

family member, genre, or some other categories. Use

buttons bm through bp (A through D) to select a folder.

Store the music data you want to play back in

one of the memory card folders.

Insert the memory card into the Digital

Piano’s memory card slot.

Press the dl (CARD/INTERNAL) button.

Press one of the folder selection buttons (bm

through bp) to select the card folder you want.

This will display the song number and song

name of the first song in the folder you

selected.

Use the bt (w, q) buttons to select the

song you want.

Press the 6 (PLAY/STOP) button.

This will start playback.

•Each press of 6 (PLAY/STOP) starts and stops

playback.

•Fast forward, fast reverse, tempo changes, and other

operations are the same as those during playback of a

user song in Digital Piano memory. For details, see

“Listening to Songs Loaded from an External Source”

(page E-25).

To quit memory card data playback, press the

dl (CARD/INTERNAL) button.

Renaming a Memory Card File

}

{

)

(

Playing Back a Song from a

Memory Card

Folder Name Button Assignment

MUSICDAT bm (A)

MUSIC__B bn (B)

MUSIC__C bo (C)

MUSIC__D bp (D)

English

Using a Memory Card

E-49

Playing Back All of the Songs in a Folder

Use the procedure below to select one of the four

folders on a memory card and play back all of the

songs in the folder in succession.

While holding down the 7 (PART) button,

press the 6 (PLAY/STOP) button.

This will start tone demo tune playback (page E-24).

Press the dl (CARD/INTERNAL) button.

This will switch from tone demo tune playback to card

tune playback.

•While playback is in progress, you can use the bm

through bp buttons (Folder A through Folder D) to

switch playback to another folder.

•To stop playback, press the 6 (PLAY/STOP) button.

Assigning a Different Folder to a Folder

Selection Button

You can use the following procedure to assign different

folders to folder selection buttons bn, bo, and bp.

While holding down the bs (FUNCTION)

button, press the folder selection button (bn,

bo, or bp) whose folder assignment you want

to change.

•This displays the folder assignment screen for the

button you press.

Use the bt (w, q) buttons to select the

folder you want to assign to the button.

•You can select any folder on the memory card.

After selecting a folder, you can rename it if

you want.

•Perform steps 6 through 8 of the procedure under

“Renaming a Memory Card File” (page E-48) to

rename the folder.

Even when you do not have a memory card loaded in

the Digital Piano’s memory card slot, you can save up

to about 16MB of data in the Digital Piano’s internal

memory area. You also can load and delete internal

memory area data using the same procedures that you

use with a memory card.

Remove the memory card from the Digital

Piano’s memory card slot (page E-45).

•Removing the memory card from the slot enables

internal memory area data operations (save, load,

delete, rename, playback).

Saving Data to Digital Piano

Memory (Internal Area) Instead

of a Memory Card

To do this Perform this operation

Save data to

the internal

memory area

From step 2 under “Saving Digital

Piano Data to a Memory Card” on page

E-46

Load data

from the

internal

memory area

From step 2 under “Loading Data from

a Memory Card” on page E-47

Delete data

from the

internal

memory area

From step 2 under “Deleting Memory

Card Data” on page E-47

Rename a file

in the internal

memory area

From step 2 under “Renaming a

Memory Card File” on page E-48

Play back a

song in the

internal

memory area

From step 3 under “Playing Back a

Song from a Memory Card” on page

E-48

• The operation in step 4 of the above

procedure is not possible in the case

of internal memory area song

playback.

E-50

Using a Memory Card

One of the error messages below appears on the display when a problem occurs.

•All mentions of “memory card” in the following table refer to an SD memory card.

Error Messages

Display

Message Cause Required Action

Convert There is not enough Digital Piano memory available to

convert a recorder song (page E-34) to SMF data and store

it on the memory card.

Reduce the size of the recorder song data by deleting unneeded

tracks (page E-37), if there are any.

Format 1. The current memory card format is not compatible

with this Digital Piano.

1. Format the memory card on the Digital Piano (page E-45).

2. The memory card capacity is greater than 2GB. 2. Use a memory card with a capacity of 2GB or less.

3. There is something wrong with the memory card. 3. Use a different memory card.

MediaFull 1. There is not enough room available on the memory

card.

1. Delete some of the files on the memory card to make room for

new data (page E-47), or use a different card.

2. There is not enough room available in Digital Piano

memory.

2. Delete some or all user data from Digital Piano memory to make

room for new data.

Media R/W 1. Memory card data is corrupted. 1. Use a different memory card.

2. Digital Piano memory is corrupted. 2. Back-up Digital Piano memory data by copying it to your

computer, and then turn the Digital Piano off and then back on

again.

• Note that you may not be able to back-up Digital Piano data

in certain cases.

No Card 1. The memory card is not loaded correctly in the Digital

Piano’s memory card slot.

1. Correctly load the memory card into the memory card slot.

2. The memory card was removed while some operation

was in progress.

2. Do not remove the memory card while any operation is in

progress.

No Data You tried to save a Digital Piano user area (user rhythm,

user rhythm song, etc.) that does not contain any data to

the memory card.

Select a user area that contains data.

No File 1. There is no MUSICDAT folder (page E-46) on the

memory card.

1. Create a MUSICDAT folder on the memory card or format the

memory card on the Digital Piano (page E-45).

2. There is no loadable or playable data in the

MUSICDAT folder, or there is no playable data in a

song playback folder (MUSIC__B, etc.)

2. Move the file you want to load or play into the memory card’s

MUSICDAT folder. For song playback, you can place the song

data into any one of the following folders: MUSIC__B,

MUSIC__C, or MUSIC__D.

Not SMF01 You are attempting to play back SMF Format 2 song data. This Digital Piano supports playback of SMF Format 0 or Format 1

only.

Protect The memory card is write-protected. Use the memory card’s write protect switch to enable writing.

ReadOnly A read-only file with the same name you are trying to use

is already stored on the memory card.

• Use a different name to save the new file.

• Remove the read-only attribute from the existing file and

overwrite it with the new file.

• Use a different memory card.

SizeOver 1. The data on the memory card is too big to play. 1. This Digital Piano supports playback of song data files with a

maximum size of about 320 kbytes.

2. The data you are trying to load is too large. 2. The following is the maximum data size (per data item) when

loading data into Digital Piano memory.

User rhythm: Approximately 40KB

User Song: 320KB

User Music Preset: Approximately 8KB

WrongDat 1. The memory card data is corrupted. —

2. The memory card contains data that is not supported

by this Digital Piano.

E-51

English

Connecting to a Computer

You can connect the Digital Piano to a computer and

exchange MIDI data between them. You can send play

data from the Digital Piano to music software running

on your computer, or you can send MIDI data from

your computer to the Digital Piano for playback.

The following shows the minimum computer system

requirements for sending and receiving MIDI data.

Check to make sure that your computer complies with

these requirements before connecting the Digital Piano

to it.

zOperating System

Windows® XP (SP2 or later)*1

Windows Vista® *2

Windows® 7 *3

Mac OS® X

(10.3.9, 10.4.11, 10.5.8 or later, 10.6.6 or later)

zUSB port

IMPORTANT!

• Never connect to a computer that does not conform

to the above requirements. Doing so can cause

problems with your computer.

IMPORTANT!

• Make sure you follow the steps of the procedure

below exactly. Connecting incorrectly can make data

send and receive impossible.

Turn off the Digital Piano and then start up

your computer.

•Do not start up the music software on your computer

yet!

After starting up your computer, use a

commercially available USB cable to connect

it to the Digital Piano.

Turn on the Digital Piano.

•If this is the first time you are connecting the Digital

Piano to your computer, the driver software required

to send and receive data will be installed on your

computer automatically.

Start up your computer’s music software.

Configure the music software settings to

select one of the following as the MIDI device.

•For information about how to select the MIDI device,

see the user documentation that comes with the

music software you are using.

IMPORTANT!

• Be sure to turn on the Digital Piano first before

starting up your computer’s music software.

Minimum Computer System

Requirements

*1: Windows XP Home Edition

Windows XP Professional (32-bit)

*2: Windows Vista (32-bit)

*3: Windows 7 (32-bit, 64-bit)

Connecting the Digital Piano

to Your Computer

CASIO USB-MIDI : (For Windows Vista, Windows 7,

Mac OS X)

USB Audio Device: (For Windows XP)

Computer USB port

A connector

B connector

Digital Piano USB port

USB cable

(A-B type)

E-52

Connecting to a Computer

NOTE

•Once you are able to connect successfully, there is no

problem with leaving the USB cable connected when

you turn off your computer and/or Digital Piano.

•This Digital Piano conforms to General MIDI Level 1

(GM).

•For detailed specifications and connections that

apply to MIDI data send and receive by this Digital

Piano, see the latest support information provided

by the website at the following URL.

http://world.casio.com/

What is MIDI?

The letters MIDI stand for Musical Instrument Digital

Interface, which is the name of a worldwide standard

for digital signals and connectors that makes it possible

to exchange musical data between musical instruments

and computers (machines) produced by different

manufacturers.

For details about the MIDI specifications of this Digital

Piano, see the “MIDI Implementation” document at the

website located at the URL below.

http://world.casio.com/

NOTE

•You can alter the Digital Piano’s MIDI setup by

changing the MIDI data send channel or other

settings. For details, see “MIDI Group” (page E-42).

•Use a separately available or commercially available

MIDI cable to connect the MIDI terminals of your

Digital Piano and another electronic musical

instrument for exchange of MIDI data.

You can use the procedure below to transfer edited

Auto Accompaniment data, recorder data, and other

data from the Digital Piano to a computer for storage.

You also can transfer standard MIDI files (SMF), as

well as Auto Accompaniment data you downloaded

from the CASIO website from your computer to Digital

Piano memory.

■Data Types Supported for Data Transfer

The types of data that can be exchanged with a

computer are the same as those that can be saved to an

SD memory card from the Digital Piano (page E-44).*

*Recorder songs (page E-34) cannot be converted to

SMF data for storage on a computer.

IMPORTANT!

• Turning off the Digital Piano while data is being

saved or loaded can cause all data currently stored

in Digital Piano memory (recorded songs, etc.) to be

deleted. Take care so power is not turned off

accidentally during data save and load operations. If

data is deleted, it will take longer than normal for the

Digital Piano to power up the next time you turn it on

(page E-9).

Remove the memory card from the Digital

Piano’s memory card slot (page E-45).

•You will not be able to transfer data between the

Digital Piano and a computer if a card is in the

memory card slot.

Perform steps 1 through 3 under “Connecting

the Digital Piano to Your Computer” to

connect the piano to your computer (page

E-51).

Using MIDI

Transferring Data between the

Digital Piano and a Computer

English

Connecting to a Computer

E-53

While holding down the bs (FUNCTION)

button, press the dm (USB DEVICE MODE)

button.

This will enter the storage mode, which enables data

transfer with the connected computer. The bs

(FUNCTION) button lamp will flash and the display

will appear as shown below.

•To exit the storage mode at any time, press the bs

(FUNCTION) button. This is the only button

operation that is supported while the Digital Piano is

in the storage mode.

•You will not be able to enter the storage mode while

any one of the following operations is in progress.

Metronome, Auto Accompaniment, song playback,

recorder (on), Auto Accompaniment editing, Music

Preset editing, data transfer between the Digital

Piano and card

If your computer is running Windows XP,

double-click “My Computer”.*

Under “Devices with Removable Storage”, you should

be able to see a folder representing Digital Piano

memory or the memory card loaded in the Digital

Piano (see below).

Windows Vista, Windows 7: Double-click “Computer”.

Mac OS: Skip step 4 and double-click “PIANO” on

your Mac desktop.

Double-click “PIANO”.

You now should see five data folders, one for each data

type.

Referring to the table below, open the folder

that corresponds to the type of data you want

to transfer.

•Data types and contents are the same as those when

saving Digital Piano data to or loading it from an SD

memory card. See “Using a Memory Card” (page

E-44) for more information.

PIANO drive (Digital Piano memory)

To load this

type of data

Open this data

folder Data File Name

User rhythms

(page E-21) RHYTHMAC BIDRHYnn.AC7

(nn: 01 to 10)

User songs

(page E-25) MUSICLIB

BIDSNGnn.MID

(nn: 01 to 10)

(SMF Format 0 or

Format 1)

BIDSNGnn.CM2

(nn: 01 to 10)

(CASIO format)

User Music Presets

(page E-28) MUSICPST BIDMPSnn.MPS

(nn: 01 to 50)

Recorder songs

(page E-34) RECORDER BIDRECnn.CSR

(nn: 01 to 05)

Registration

(page E-32) REGISTMR BIDREGAL.CR6

This folder is not a data folder. You should not try to

use it for normal Digital Piano operation.

E-54

Connecting to a Computer

File name extensions (.MID, .CM2, etc.) are

not displayed under initial default Windows

settings. Perform the procedure below to turn

on display of file name extensions.

After opening a data folder, perform either of

the following operations to transfer data.

Example: Renaming downloaded song data to

BIDSNG04.CM2 to the MUSICLIB folder will

make the data user song 004.

Press the bs (FUNCTION) button to exit the

storage mode.

•If you are using a Macintosh, drag the PIANO folder

to the Trash and then press the Digital Piano’s bs

(FUNCTION) button.

IMPORTANT!

• The message “ERROR, DATA EXCHANGE” will

appear on the display if a problem occurs during

data transfer. If this happens, check the message in

the “STATELOG” folder (page E-53) on the “PIANO”

drive. Next find the same message in the table on

page E-50 of this manual to determine the cause of

the problem and what action you need to take to

avoid it.

(1) Open any one of the folders shown above.

(2) Perform one of the following operations to display

folder information.

•Windows XP:

On the [Tools] menu at the top of the folder

window, select [Folder Options].

•Windows Vista, Windows 7:

On the left side of the folder window, click

[Organize] and then select [Folder and Search

Options].

(3) On the Folder Information window, click the

[View] tab.

(4) Under “Advanced Settings”, clear the “Hide

extensions for known file types” check box and

then click [OK].

8-1.To transfer data from Digital Piano

memory to a computer, perform the

required operation on your computer to

copy the data from the Digital Piano

folder you opened in step 6 of this

procedure to another location on your

computer.

8-2.To load data from your computer to

Digital Piano memory, first copy the data

you want to load to the data folder you

opened. Next, rename the file as shown

in the “Data File Name” * column in the

table under step 6 of this procedure.

*The value you assign for “nn” in the data file name in

this case specifies the user number (user rhythm, user

song, recorder song, user preset) you want the data to

be assigned to.

English

Connecting to a Computer

E-55

Playing Back User Song Data by Copying

It to the PIANO Drive

You can use the procedure below at any time to copy

user song data to the PIANO drive (without putting it

in the MUSICLIB folder) for simplified playback on the

Digital Piano.

•When you copy a user song data file to the

MUSICLIB folder, you need to rename it according

to specified format (page E-53, step 6). You do not

need to rename the file if you use the procedure

below.

Perform the previous procedure to copy the

user song data file to the PIANO drive.

Press the dl (CARD/INTERNAL) button.

This will cause the button’s lamp to light and will the

display the song number and song name of the first

song on the PIANO drive.

Use the bt (w, q) buttons to select the

song you want to play.

Press the 6 (PLAY/STOP) button.

This starts playback of the selected song.

•Each press of the 6 (PLAY/STOP) button toggles

between play and stop.

•Fast forward, fast reverse, tempo change, and other

operations are the same as those during playback of a

loaded user song and a song file on a memory card.

When you are finished playing back songs,

press the dl (CARD/INTERNAL) button.

Using Your Digital Piano as a Memory

Card Reader

You can display the contents of the memory card

currently loaded in the Digital Piano’s card slot and

perform copy, delete, and other card operations from

your computer.

Insert the memory card into the Digital

Piano’s memory card slot.

Perform the procedure starting from step 2 on

page E-52.

In step 4 of the procedure, “SD_MMC” will appear in

place of “PIANO”. You can double-click “SD_MMC” to

display the contents of the card loaded in the Digital

Piano card slot, and change it as you like.

■Using Auto Accompaniment Data from the

CASIO Website

You can download other model Auto Accompaniment

data from the “Internet Data Expansion System” of the

CASIO Music Site (http://music.casio.com/) and

transfer it to Digital Piano memory.

NOTE

•Since the accompaniment data is for other models,

you may experience some abnormalities when

playing it on this model.

CASIO format song data MIDI file song data

Copyrights

The rights of creators and copyright holders of music,

images, computer programs, databases, and other

data are protected by copyright laws. You are allowed

to reproduce such works for personal or non-

commercial use only. For any other purpose, all

reproduction (including data format conversion),

modification, transfer of reproductions, distribution

over a network, or any other use without permission

of the copyright holder exposes you to claims for

damages and criminal prosecution for copyright

infringement and violation of the author’s personal

rights. Be sure to reproduce and otherwise use

copyrighted works only in accordance with applicable

E-56

Reference

Troubleshooting

Problem Cause Action See Page

No sound is produced when I

press a keyboard key.

1. The VOLUME controller is set to

“MIN”.

1. Rotate the VOLUME controller more towards

“MAX”.

) E-9

2. Headphones or an adaptor plug is

plugged into one of the PHONES

jacks.

2. Disconnect whatever is connected to the

PHONES jack.

) E-6

The pitch of the Digital Piano is

off.

1. The Digital Piano’s key setting is

something other than “00”.

1. Change the key setting to “00”, or turn Digital

Piano power off and then back on again.

) E-41

2. Digital Piano tuning is incorrect. 2. Adjust Digital Piano tuning, or turn the piano

off and then back on again.

) E-41

3. A non-standard temperament setting

is being used.

3. Change the temperament setting to

“00:Equal”, which is the standard modern

tuning.

) E-41

4. Octave shift is enabled. 4. Change the octave shift setting to 0. ) E-12

Tones and/or effects sound

strange. Turning power off and

then back on again does not

eliminate the problem.

Example:

Note intensity does not

change even though I alter key

pressure.

The “Setting Backup” feature is turned

on.

Turn off “Setting Backup”. Next, turn power off

and then back on again.

) E-43

I cannot transfer data after

connecting the Digital Piano to a

computer.

— 1. Check to make sure that the USB cable is

connected to the Digital Piano and computer,

and that the correct device is selected with

your computer’s music software.

) E-51

2. Turn off the Digital Piano and then exit the

music software on your computer. Next, turn

the Digital Piano back on and then restart the

music software on your computer.

I cannot record chord

accompaniment data on my

computer.

Accomp MIDI Out is turned off. Turn on Accomp MIDI Out. ) E-42

I cannot store data to a memory

card or load data from a memory

card.

— See “Error Messages” on page E-50. —

Playback stops part way through

while transferring song data from

my computer.

Digital noise from the USB cable or

power cord caused data communication

your computer and Digital Piano to be

interrupted.

Stop song playback, disconnect the USB cable

from the Digital Piano, and then reconnect it.

Next, try playing back the song again.

If this does not solve the problem, quit the MIDI

software you are using, disconnect the USB

cable from the Digital Piano, and then reconnect

it. Next, restart the MIDI software and then try

playing back the song again.

) E-51

A tone’s quality and volume

sounds slightly different

depending where it is played on

the keyboard.

This is an unavoidable result of the digital sampling process,* and does not indicate malfunction.

*Multiple digital samples are taken for the low range, middle range, and high range of the original

musical instrument. Because of this, there may be a very slight difference in tonal quality and volume

between sample ranges.

When I press a button, the note

that is sounding cuts out

momentarily or there is a slight

change in how effects are applied.

Performing a button operation while playing with the Duet Mode, Auto Accompaniment, the recorder, or

other functions can cause such phenomena when the Digital Piano switches internal tone effects. It does

not indicate malfunction.

Even though I play on different

ranges of the keyboard, the notes

do not change octaves.

The ranges of certain tones are limited, which means that octaves change normally up to a certain low

note or high note. With such a tone, the notes of the lowest octave will be repeated to the left of the

lowest possible note, and the highest octave will be repeated to the right of the highest possible note.

This is due do limitations in the range of the original musical instrument for each tone, and does not

indicate malfunction of the Digital Piano.

Reference

E-57

English

*Based on 1KB = 1024bytes, 1MB = 10242 bytes

• Specifications and designs are subject to change without notice.

Product Specifications

Model PX-330BK/PX-330WE

Keyboard 88-key piano keyboard, with Touch Response (3 types)

Maximum Polyphony 128 notes

Tones 250 (with Layer and Split)

Effects Reverb (4 types), Chorus (4 types), Brilliance (–3 to 0 to 3), Acoustic Resonance

Metronome • Beats per measure: 0, 2, 3, 4, 5, 6

• Tempo Range: 20 to 255

Duet Adjustable tone range: 0 to 3 octaves for the left keyboard; –4 to –1 octaves for the right keyboard

Auto Accompaniment • Built-in Rhythms: 180

• User Rhythms: Up to 10 (Approximately 40KB* maximum per rhythm)

• One Touch Presets: 180 types

• Auto Harmonize: 12 types

Demo Songs 8 songs (tone demo songs)

User Songs Up to 10 songs (320KB* maximum per song)

Music Presets Built-in Presets: 300

User Presets: Up to 50 (Approximately 8KB* maximum per preset)

Registration (4 rhythm areas + 8 tone areas) × 8 banks

Recorder • Functions: Real-time recording, playback

• Number of Songs: 5

• Number of Tracks: 17 (System Track + Tracks 01 through 16)

• Capacity: Approximately 50,000 notes total (Up to approximately 10,000 notes per song)

• Punch-in recording

Pedals Damper, Soft/Sostenuto (switchable)

Other Functions • Transpose: ±1 octave (–12 to 00 to 12)

• Tuning: A4 = 440.0 Hz ±99 cents

• Octave Shift: ±2 octaves

• Temperaments: 17 types

• Stretch Tune

• Panel Lock

MIDI 16 multi-timbre received, GM Level 1 standard

Pitch Bend Wheel Pitch Bend Range: 00 to 12 semitones

SD Memory Card • SD memory card slot

• Supported SD Memory Cards: Up to 2GB

• Functions: SMF playback, file storage, file recall, card format

Inputs/Outputs • PHONES jacks: Stereo mini jacks × 2

• Pedal Jacks: Standard jacks × 2

•MIDI OUT/IN terminals

•LINE OUT R, L/MONO jacks: Standard jacks × 2

Output impedance: 2.3KΩ

Output voltage: 1.8V (RMS) MAX

•LINE IN R, L/MONO jacks: Standard jacks × 2

Input impedance: 9.0KΩ

Input voltage: 200mV

• Power: 12V DC

•USB port: Type B

• Pedal connector (for optional SP-32 only)

Speakers [13cm × 6cm (rectangular)] × 2 +

5cm × 2 (Output: 8.0W + 8.0W)

Power Requirements AC Adaptor: AD-A12150LW

Power Consumption 12V = 18W

Dimensions 132.2 (W) × 28.6 (D) × 13.5 (H) cm (52 1/16 × 11 1/4 × 5 5/16 inch)

Weight Approximately 11.6kg (25.6lbs)

E-58

Reference

Be sure to read and observe the following operating

precautions.

■Location

Avoid the following locations for this product.

•Areas exposed to direct sunlight and high humidity

•Areas subjected to temperature extremes

•Near a radio, TV, video deck, or tuner

•The above devices will not cause malfunction of the

product, but the product can cause interference in

the audio or video of a nearby device.

■User Maintenance

•Never use benzine, alcohol, thinner, or other

chemical agents to clean the product.

•To clean the product or its keyboard, wipe with a

soft cloth moistened in a weak solution of water and

a mild neutral detergent. Wring all excess moisture

from the cloth before wiping.

■Included and Optional Accessories

Use only accessories that are specified for use with this

product. Use of unauthorized accessories creates the

risk of fire, electric shock, and personal injury.

■Weld Lines

Lines may be visible on the exterior of the product.

These are “weld lines” that result from the plastic

molding process. They are not cracks or scratches.

■Musical Instrument Etiquette

Always be aware of others around you whenever using

this product. Be especially careful when playing late at

night to keep the volume at levels that do not disturb

others. Other steps you can take when playing late at

night are closing windows and using headphones.

•Any reproduction of the contents of this manual,

either in part or its entirety, is prohibited. Except for

your own, personal use, any other use of the

contents of this manual without the consent of

CASIO is prohibited under copyright laws.

•IN NO EVENT SHALL CASIO BE LIABLE FOR

ANY DAMAGES WHATSOEVER (INCLUDING,

WITHOUT LIMITATION, DAMAGES FOR LOSS

OF PROFITS, BUSINESS INTERRUPTION, LOSS

OF INFORMATION) ARISING OUT OF THE USE

OF OR INABILITY TO USE THIS MANUAL OR

PRODUCT, EVEN IF CASIO HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

•The contents of this manual are subject to change

without notice.

■AC Adaptor Handling Precautions

•Use a power outlet that is easily accessible so you

can unplug the AC adaptor when a malfunction

occurs or whenever else you need to do so.

•The AC adaptor is intended for indoor use only. Do

not use it where it might be exposed to splashing or

moisture. Do not place any container, such as a

flower vase, that contains liquid on the AC adaptor.

•Store the AC adaptor in a dry place.

•Use the AC adaptor in an open, well-ventilated area.

•Never cover the AC adaptor with newspaper, a table

cloth, a curtain, or any other similar item.

•Unplug the AC adaptor from the power outlet if you

do not plan to use the Digital Piano for a long time.

•Never try to repair the AC adaptor or modify it in

any way.

•AC adaptor operating environment

Temperature: 0 to 40°C

Humidity: 10% to 90% RH

Output polarity:

Operating Precautions

Reference

E-59

English

AC Adaptor Handling Precautions

Model: AD-A12150LW

1. Read these instructions.

2. Keep these instructions on hand.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this product near water.

6. Clean only with a dry cloth.

7. Do not install near radiators, heat registers, stoves, or any other source of heat (including amplifiers).

8. Use only attachments and accessories specified by the manufacturer.

9. Refer all servicing to qualified service personnel. Servicing is required after any of the following occurs:

when the product is damaged, when the power supply cord or plug is damaged, when liquid is spilled into

the product, when a foreign object falls into the product, when the product is exposed to rain or moisture,

when the product does not operate normally, when the product is dropped.

10. Do not allow the product to be exposed to dripping or splashing liquid. Do not place any object containing

liquid on the product.

11. Do not allow the electrical load output to exceed the label rating.

12. Make sure the surrounding area is dry before plugging into a power source.

13. Make sure the product is oriented correctly.

14. Unplug the product during lightning storms or when you do not plan to use it for a long time.

15. Do not allow product ventilation openings to become blocked. Install the product in accordance with the

manufacturer’s instructions.

16. Take care the power cord is located where it will not be stepped upon or bent severely, particularly in

locations close to plugs and convenience receptacles, and in locations where it exits from the product.

17. The AC adaptor should be plugged into a power outlet as close to the product as possible to allow

immediate disconnection of the plug in case of emergency.

The symbol below is an alert indicating un-insulated hazardous voltage inside the product’s enclosure, which

may be sufficient to constitute the risk of electric shock to users.

’

The symbol below is an alert indicating the presence of important operating and maintenance (servicing)

instructions in the documentation that accompanies the product.

A-1

Appendix/Apéndice

Tone List/Lista de tonos

Group

Name/

Nombre

del

grupo

Group

Number/

Número

grupo

Sequential

Number/

Número

secuencial

Tone Name/

Nombre del tono

Program

Change/

Cambio

programa

Bank

Select

MSB/

MSB de

Selección

de banco

Acoustic

Resonance/

Resonancia

acústica

GRAND PIANO MODERN

001 001 GRAND PIANO MODERN 0 48 O

002 002 GRAND PIANO

VARIATION 0 50 O

003 003 ROCK PIANO 1 48 O

004 004 LA PIANO 1 49 O

005 005 MODERN PIANO 1 50 O

006 006 DANCE PIANO 1 51 O

GRAND PIANO CLASSIC

001 007 GRAND PIANO CLASSIC 0 49 O

002 008 MELLOW PIANO 0 51 O

003 009 HONKY-TONK 3 48 O

004 010 OCTAVE PIANO 3 49 O

005 011 STRINGS PIANO 0 52 O

006 012 PIANO PAD 0 53 O

ELEC PIANO

001 013 ELEC.PIANO 1 4 48

002 014 ELEC.PIANO 2 5 48

003 015 60’S E.PIANO 4 51

004 016 E.GRAND 80 2 48

005 017 DYNO ELEC.PIANO 4 49

006 018 FM ELEC.PIANO 5 49

007 019 MELLOW E.PIANO 4 50

008 020 POP ELEC.PIANO 5 50

009 021 SYNTH-STR.E.PIANO 4 52

VIBES/CLAVI

001 022 VIBRAPHONE 11 48

002 023 CLAVI 7 48

003 024 HARPSICHORD 6 48

004 025 COUPLED

HARPSICHORD 6 49

005 026 MARIMBA 12 48

006 027 CHORUS VIBRAPHONE 11 49

ORGAN

001 028 ROCK ORGAN 1 16 49

002 029 JAZZ ORGAN 17 48

003 030 DRAWBAR ORGAN 16 48

004 031 ROTARY DRAWBAR 16 50

005 032 ROTARY ORGAN 16 51

006 033 PERC.ORGAN 17 49

007 034 70’S ORGAN 17 50

008 035 OVERDRIVE ORGAN 16 52

009 036 TREMOLO ORGAN 16 53

010 037 ROCK ORGAN 2 18 48

011 038 ELEC.ORGAN 16 54

012 039 CHURCH ORGAN 19 48

013 040 CHAPEL ORGAN 19 49

STRINGS/SYNTH-PAD

001 041 STRINGS 49 48

002 042 STRING ENSEMBLE 48 48

003 043 SYNTH-STRINGS 50 48

004 044 70’S SYNTH-STR. 50 49

005 045 80’S SYNTH-STR. 50 50

006 046 VIOLIN SECTION 40 48

007 047 CHOIR 52 48

008 048 SYNTH-VOICE 54 48

009 049 SYNTH-PAD 90 48

010 050 FANTASY 88 48

011 051 NEW AGE 88 49

012 052 WARM PAD 89 48

013 053 WARM VOX 89 49

014 054 POLYSYNTH PAD 90 49

015 055 ATMOSPHERE PAD 99 48

BASS/GUITAR

001 056 ACOUSTIC BASS 32 48

002 057 RIDE BASS 32 49

003 058 FINGERED BASS 1 33 48

004 059 FINGERED BASS 2 33 49

005 060 FINGERED BASS 3 33 50

006 061 PICKED BASS 34 48

007 062 TRANCE BASS 38 48

008 063 NYLON STR.GUITAR 24 48

009 064 STEEL STR.GUITAR 1 25 48

010 065 STEEL STR.GUITAR 2 25 49

011 066 STEEL STR.GUITAR 3 25 50

012 067 JAZZ GUITAR 26 48

013 068 CLEAN GUITAR 27 49

014 069 CHORUS CLEAN GUITAR 27 48

015 070 CRUNCH ELEC.GUITAR 1 27 50

016 071 CRUNCH ELEC.GUITAR 2 27 51

017 072 OVERDRIVE GUITAR 29 48

VARIOUS/GM TONES

001 073 BREATHY ALTO SAX 65 49

002 074 BREATHY TENOR SAX 66 49

003 075 ALTO SAX 65 48

004 076 TENOR SAX 66 48

005 077 CLARINET 71 48

006 078 FLUTE 73 48

007 079 TRUMPET 56 48

008 080 TROMBONE 57 48

009 081 STEREO BRASS 61 48

010 082 BRASS SECTION 61 49

011 083 SYNTH-BRASS 62 48

012 084 80’S SYNTH-BRASS 62 49

013 085 SAW LEAD 81 48

014 086 MELLOW SAW LEAD 81 49

015 087 SQUARE LEAD 80 48

016 088 ER HU 110 56

017 089 YANG QIN 1 15 56

018 090 YANG QIN 2 15 57

019 091 DI ZI 72 56

020 092 ZHENG 107 56

021 093 SHENG 109 56

022 094 SUO NA 111 57

023 095 XIAO 77 56

024 096 PI PA 1 105 56

025 097 PI PA 2 105 57

026 098 SITAR 104 56

027 099 TANPURA 104 57

028 100 HARMONIUM 20 56

029 101 SANTUR 15 58

030 102 SAROD 105 58

031 103 SHANAI 111 56

032 104 SARANGI 110 57

033 105 KANUN 15 59

034 106 OUD 105 59

035 107 NEY 72 57

036 108 ARABIC ORGAN 16 56

037 109 GM PIANO 1 0 0 O

038 110 GM PIANO 2 1 0 O

039 111 GM PIANO 3 2 0

040 112 GM HONKY-TONK 3 0

041 113 GM E.PIANO 1 4 0

042 114 GM E.PIANO 2 5 0

043 115 GM HARPSICHORD 6 0

044 116 GM CLAVI 7 0

045 117 GM CELESTA 8 0

046 118 GM GLOCKENSPIEL 9 0

047 119 GM MUSIC BOX 10 0

048 120 GM VIBRAPHONE 11 0

049 121 GM MARIMBA 12 0

050 122 GM XYLOPHONE 13 0

051 123 GM TUBULAR BELL 14 0

052 124 GM DULCIMER 15 0

053 125 GM ORGAN 1 16 0

054 126 GM ORGAN 2 17 0

055 127 GM ORGAN 3 18 0

056 128 GM PIPE ORGAN 19 0

057 129 GM REED ORGAN 20 0

058 130 GM ACCORDION 21 0

059 131 GM HARMONICA 22 0

060 132 GM BANDONEON 23 0

061 133 GM NYLON STR.GUITAR 24 0

Group

Name/

Nombre

del

grupo

Group

Number/

Número

grupo

Sequential

Number/

Número

secuencial

Tone Name/

Nombre del tono

Program

Change/

Cambio

programa

Bank

Select

MSB/

MSB de

Selección

de banco

Acoustic

Resonance/

Resonancia

acústica

Appendix/Apéndice

A-2

NOTE

•Acoustic resonance (page E-41) is applied only to

tones indicated by “O”.

•While sequential numbered tone 065 (STEEL

STR.GUITAR 2) or 066 (STEEL STR.GUITAR 3) is

selected, pressing multiple keys on the far left side of

the keyboard will produce a guitar strumming

sound. It does not indicate malfunction.

•See the “Drum Assignment List” (page A-3) for the

percussion instrument assigned to each keyboard

key when a drum set (Sequential Number 237 to 250)

is selected.

•La resonancia acústica (página S-42) se aplica

solamente a los tonos indicados mediante “O”.

•Cuando los tonos secuenciales número 065 (STEEL

STR. GUITAR 2) o 066 (STEEL STR. GUITAR 3)

estén seleccionados, si presiona múltiples teclas en el

extremo izquierdo del teclado producirá un sonido

de rasgueo de guitarra. Esto no es ningún signo de

anomalía.

•Consulte la “Lista de asignación de batería”

(página A-3) para saber cuáles son los instrumentos

de percusión asignados a cada tecla cuando se

selecciona un ajuste de batería (números

secuenciales 237 a 250).

062 134 GM STEEL STR.GUITAR 25 0

063 135 GM JAZZ GUITAR 26 0

064 136 GM CLEAN GUITAR 27 0

065 137 GM MUTE GUITAR 28 0

066 138 GM OVERDRIVE GT 29 0

067 139 GM DISTORTION GT 30 0

068 140 GM GT HARMONICS 31 0

069 141 GM ACOUSTIC BASS 32 0

070 142 GM FINGERED BASS 33 0

071 143 GM PICKED BASS 34 0

072 144 GM FRETLESS BASS 35 0

073 145 GM SLAP BASS 1 36 0

074 146 GM SLAP BASS 2 37 0

075 147 GM SYNTH-BASS 1 38 0

076 148 GM SYNTH-BASS 2 39 0

077 149 GM VIOLIN 40 0

078 150 GM VIOLA 41 0

079 151 GM CELLO 42 0

080 152 GM CONTRABASS 43 0

081 153 GM TREMOLO STRINGS 44 0

082 154 GM PIZZICATO 45 0

083 155 GM HARP 46 0

084 156 GM TIMPANI 47 0

085 157 GM STRINGS 1 48 0

086 158 GM STRINGS 2 49 0

087 159 GM SYNTH-STRINGS 1 50 0

088 160 GM SYNTH-STRINGS 2 51 0

089 161 GM CHOIR AAHS 52 0

090 162 GM VOICE DOO 53 0

091 163 GM SYNTH-VOICE 54 0

092 164 GM ORCHESTRA HIT 55 0

093 165 GM TRUMPET 56 0

094 166 GM TROMBONE 57 0

095 167 GM TUBA 58 0

096 168 GM MUTE TRUMPET 59 0

097 169 GM FRENCH HORN 60 0

098 170 GM BRASS 61 0

099 171 GM SYNTH-BRASS 1 62 0

100 172 GM SYNTH-BRASS 2 63 0

101 173 GM SOPRANO SAX 64 0

102 174 GM ALTO SAX 65 0

103 175 GM TENOR SAX 66 0

104 176 GM BARITONE SAX 67 0

105 177 GM OBOE 68 0

106 178 GM ENGLISH HORN 69 0

107 179 GM BASSOON 70 0

108 180 GM CLARINET 71 0

109 181 GM PICCOLO 72 0

110 182 GM FLUTE 73 0

111 183 GM RECORDER 74 0

112 184 GM PAN FLUTE 75 0

113 185 GM BOTTLE BLOW 76 0

114 186 GM SHAKUHACHI 77 0

115 187 GM WHISTLE 78 0

116 188 GM OCARINA 79 0

117 189 GM SQUARE LEAD 80 0

118 190 GM SAW LEAD 81 0

119 191 GM CALLIOPE 82 0

120 192 GM CHIFF LEAD 83 0

121 193 GM CHARANG 84 0

122 194 GM VOICE LEAD 85 0

123 195 GM FIFTH LEAD 86 0

124 196 GM BASS+LEAD 87 0

125 197 GM FANTASY 88 0

126 198 GM WARM PAD 89 0

127 199 GM POLYSYNTH 90 0

128 200 GM SPACE CHOIR 91 0

129 201 GM BOWED GLASS 92 0

130 202 GM METAL PAD 93 0

131 203 GM HALO PAD 94 0

132 204 GM SWEEP PAD 95 0

133 205 GM RAIN DROP 96 0

134 206 GM SOUND TRACK 97 0

135 207 GM CRYSTAL 98 0

136 208 GM ATMOSPHERE 99 0

137 209 GM BRIGHTNESS 100 0

138 210 GM GOBLINS 101 0

139 211 GM ECHOES 102 0

Group

Name/

Nombre

del

grupo

Group

Number/

Número

grupo

Sequential

Number/

Número

secuencial

Tone Name/

Nombre del tono

Program

Change/

Cambio

programa

Bank

Select

MSB/

MSB de

Selección

de banco

Acoustic

Resonance/

Resonancia

acústica

140 212 GM SF 103 0

141 213 GM SITAR 104 0

142 214 GM BANJO 105 0

143 215 GM SHAMISEN 106 0

144 216 GM KOTO 107 0

145 217 GM THUMB PIANO 108 0

146 218 GM BAGPIPE 109 0

147 219 GM FIDDLE 110 0

148 220 GM SHANAI 111 0

149 221 GM TINKLE BELL 112 0

150 222 GM AGOGO 113 0

151 223 GM STEEL DRUMS 114 0

152 224 GM WOOD BLOCK 115 0

153 225 GM TAIKO 116 0

154 226 GM MELODIC TOM 117 0

155 227 GM SYNTH-DRUM 118 0

156 228 GM REVERSE CYMBAL 119 0

157 229 GM GT FRET NOISE 120 0

158 230 GM BREATH NOISE 121 0

159 231 GM SEASHORE 122 0

160 232 GM BIRD 123 0

161 233 GM TELEPHONE 124 0

162 234 GM HELICOPTER 125 0

163 235 GM APPLAUSE 126 0

164 236 GM GUNSHOT 127 0

165 237 STANDARD SET 1 0 120

166 238 STANDARD SET 2 1 120

167 239 STANDARD SET 3 2 120

168 240 STANDARD SET 4 3 120

169 241 ROOM SET 8 120

170 242 HIP-HOP SET 9 120

171 243 POWER SET 16 120

172 244 ELECTRONIC SET 24 120

173 245 SYNTH SET 1 25 120

174 246 SYNTH SET 2 30 120

175 247 TRANCE SET 31 120

176 248 JAZZ SET 32 120

177 249 BRUSH SET 40 120

178 250 ORCHESTRA SET 48 120

Group

Name/

Nombre

del

grupo

Group

Number/

Número

grupo

Sequential

Number/

Número

secuencial

Tone Name/

Nombre del tono

Program

Change/

Cambio

programa

Bank

Select

MSB/

MSB de

Selección

de banco

Acoustic

Resonance/

Resonancia

acústica

NOTA

A-3

Appendix/Apéndice

Drum Assignment List/Lista de sonidos de batería

F#1

C#2

F#2

C#3

F#3

C#4

F#4

C#5

F#5

C#6

High Q

Slap

Scratch Push

Scratch Pull

Sticks

Square Click

Metronome Click

Metronome Bell

Standard1 Kick 2

Standard1 Kick 1

Side Stick

Standard1 Snare 1

Hand Clap

Standard1 Snare 2

Low Tom 2

Closed Hi-Hat

Low Tom 1

Pedal Hi-Hat

Mid Tom 2

Open Hi-Hat

Mid Tom 1

High Tom 2

Crash Cymbal 1

High Tom 1

Ride Cymbal 1

Chinese Cymbal

Ride Bell

Tambourine

Splash Cymbal

Cowbell

Crash Cymbal 2

Vibraslap

Ride Cymbal 2

High Bongo

Low Bongo

Mute High Conga

Open High Conga

Open Low Conga

High Timbale

Low Timbale

High Agogo

Low Agogo

Cabasa

Maracas

Short High Whistle

Long Low Whistle

Short Guiro

Long Guiro

Claves

High Wood Block

Low Wood Block

Mute Cuica

Open Cuica

Mute Triangle

Open Triangle

Shaker

Jingle Bell

Bell Tree

Castanets

Mute Surdo

Open Surdo

Applause 1

Applause 2



Standard2 Kick 2

Standard2 Kick 1



Standard2 Snare 1



Standard2 Snare 2



Standard2 Closed Hi-Hat



Standard2 Pedal Hi-Hat



Standard2 Open Hi-Hat



Standard4 Kick 2

Standard4 Kick 1



Standard4 Snare 1



Standard4 Snare 2



Room Kick 2

Room Kick 1



Room Snare 1



Room Snare 2

Room Low Tom 2



Room Low Tom 1



Room Mid Tom 2



Room Mid Tom 1

Room High Tom 2



Room High Tom 1



Hip-Hop Kick 2

Hip-Hop Kick 1

Hip-Hop Side Stick

Hip-Hop Snare 1

Hip-Hop Hand Clap

Hip-Hop Snare 2



Hip-Hop Closed Hi-Hat



Hip-Hop Pedal Hi-Hat



Hip-Hop Open Hi-Hat



Power Kick 2

Power Kick 1



Power Snare 1



Power Snare 2

Room Low Tom 2



Room Low Tom 1



Room Mid Tom 2



Room Mid Tom 1

Room High Tom 2



Room High Tom 1



Elec. Kick 2

Elec. Kick 1



Elec. Snare 1



Elec. Snare 2

Elec. Low Tom 2



Elec. Low Tom 1



Elec. Mid Tom 2



Elec. Mid Tom 1

Elec. High Tom 2



Elec. High Tom 1



Reverse Cymbal



Synth1 Kick 2

Synth1 Kick 1

Synth1 Rim Shot

Synth1 Snare 1

Synth1 Hand Clap

Synth1 Snare 2

Synth1 Low Tom 2

Synth1 Closed Hi-Hat 1

Synth1 Low Tom 1

Synth1 Closed Hi-Hat 2

Synth1 Mid Tom 2

Synth1 Open Hi-Hat

Synth1 Mid Tom 1

Synth1 High Tom 2

Synth1 Crash Cymbal

Synth1 High Tom 1

Synth1 Ride Cymbal



Synth1 Tambourine



Synth1 Cowbell



Synth1 High Bongo

Synth1 Low Bongo

Synth1 Mute Hi Conga

Synth1 Open Hi Conga

Synth1 Open Low Conga



Synth1 Maracas



Synth1 Claves



Synth2 Kick 2

Synth2 Kick 1

Synth1 Rim Shot

Synth2 Snare 1



Synth2 Snare 2

Synth2 Low Tom 2

Synth2 Closed Hi-Hat 1

Synth2 Low Tom 1

Synth2 Closed Hi-Hat 2

Synth2 Mid Tom 2

Synth2 Open Hi-Hat

Synth2 Mid Tom 1

Synth2 High Tom 2



Synth2 High Tom 1



Synth1 Cowbell



Synth1 Maracas



Synth1 Claves



Trance Kick 2

Trance Kick 1

Trance Side Stick

Trance Snare 1

Trance Hand Clap

Trance Snare 2



Trance Closed Hi-Hat



Trance Open Hi-Hat 1



Trance Open Hi-Hat 2



Trance Tambourine



Jazz Kick 2

Jazz Kick 1



Jazz Snare 1



Jazz Snare 2



Jazz Kick 2

Brush Kick

Brush Side Stick

Brush Snare 1

Brush Slap

Brush Snare 2



Brush Crash Cymbal 1



Brush Ride Cymbal 1



Brush Ride Bell

Brush Tambourine

Brush Splash Cymbal



Brush Crash Cymbal 2



Brush Ride Cymbal 2



Closed Hi-Hat

Pedal Hi-Hat

Open Hi-Hat

Ride Cymbal 1



Jazz Kick 1

Concert BD



Concert SD

Castanets

Concert SD

Timpani F

Timpani F#

Timpani G

Timpani G#

Timpani A

Timpani A#

Timpani B

Timpani c

Timpani c#

Timpani d

Timpani d#

Timpani e

Timpani f



Concert Cymbal 2



Concert Cymbal 1



Standard3 Kick 2

Standard3 Kick 1

Standard3 Side Stick

Standard3 Snare 1

Standard3 Hand Clap

Standard3 Snare 2

Standard3 Low Tom 2

Standard3 Closed Hi-Hat

Standard3 Low Tom 1

Standard3 Pedal Hi-Hat

Standard3 Mid Tom 2

Standard3 Open Hi-Hat

Standard3 Mid Tom 1

Standard3 High Tom 2



Standard3 High Tom 1



STANDARD

SET 1

STANDARD

SET 2

STANDARD

SET 3

STANDARD

SET 4 ROOM SET HIP-HOP SET POWER SET ELECTRONIC

SET SYNTH SET 1 SYNTH SET 2 TRANCE SET JAZZ SET BRUSH SET ORCHESTRA

SET

Key/Note Number

Número de clave/nota

•“»” indicates a key is assigned the same tones as it is for STANDARD SET.

•“»” indica una clave asignada a los mismos tonos que para STANDARD SET.

Appendix/Apéndice

A-4

Rhythm List/Lista de ritmos

Group Name/

Nombre del

grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Rhythm name/

Nombre del ritmo

POPS/JAZZ

POPS

001 001 POP 1

002 002 POP 2

003 003 FAST POP

004 004 FUNK POP

005 005 POP ROCK

006 006 6/8 POP

007 007 FAST SOUL

008 008 SLOW SOUL

009 009 60’S SOUL

010 010 POP SHUFFLE

8 BEAT/16 BEAT

011 011 STRAIGHT 8 BEAT 1

012 012 STRAIGHT 8 BEAT 2

013 013 FUNK 8 BEAT

014 014 MELLOW 8 BEAT

015 015 GUITAR 8 BEAT

016 016 8 BEAT

017 017 8 BEAT POP

018 018 OLDIES 8 BEAT

019 019 60’S 8 BEAT

020 020 16 BEAT

021 021 16 BEAT SHUFFLE

DANCE

022 022 HIP-HOP

023 023 DANCE POP

024 024 DISCO POP

025 025 TECHNO POP

026 026 TRANCE

027 027 MODERN R&B

028 028 MODERN DANCE

029 029 DISCO SOUL

ROCK

030 030 STRAIGHT ROCK

031 031 SHUFFLE ROCK

032 032 BLUES 1

033 033 BLUES 2

034 034 EP BLUES

035 035 SLOW BLUES

036 036 SOFT ROCK

037 037 LATIN ROCK

038 038 SLOW ROCK

039 039 50’S ROCK

040 040 50’S PIANO ROCK

041 041 NEW ORLNS R&R

042 042 60’S ROCK

043 043 ROCK

044 044 70’S PIANO ROCK

045 045 ROCK WALTZ

JAZZ

046 046 SLOW BIG BAND

047 047 MIDDLE BIG BAND

048 048 FAST BIG BAND

049 049 SWING 1

050 050 SWING 2

051 051 SLOW SWING

052 052 JAZZ WALTZ

053 053 FOX TROT

054 054 QUICKSTEP

055 055 JAZZ COMBO 1

EUROPEAN

056 056 SCHLAGER

057 057 POLKA

058 058 WALTZ 1

059 059 WALTZ 2

060 060 SLOW WALTZ

061 061 VIENNESE WALTZ

062 062 FRENCH WALTZ

063 063 SERENADE

064 064 TANGO

065 065 MARCH 1

066 066 MARCH 2

LATIN/WORLD

LATIN I

001 067 BOSSA NOVA

002 068 SLOW BOSSA NOVA

003 069 BEGUINE

004 070 SAMBA 1

005 071 SAMBA 2

006 072 MAMBO

007 073 RHUMBA

008 074 CHA-CHA-CHA

009 075 MERENGUE

010 076 BOLERO

011 077 SALSA 1

012 078 SALSA 2

013 079 REGGAE

014 080 POP REGGAE

015 081 SKA

LATIN II

016 082 REGGAETON 1

017 083 REGGAETON 2

018 084 CUMBIA

019 085 CALYPSO

020 086 FORRO

021 087 PAGODE

022 088 BANDA

023 089 PASILLO

024 090 ARGENTINE CUMBIA

025 091 PUNTA

026 092 BACHATA

COUNTRY

027 093 MODERN COUNTRY

028 094 COUNTRY 8 BEAT

029 095 COUNTRY BALLAD

030 096 COUNTRY SHUFFLE

031 097 FINGER PICKING

COUNTRY

032 098 COUNTRY WALTZ

033 099 BLUEGRASS

WORLD I

AMERICAN

034 100 DIXIE

035 101 TEX-MEX

036 102 FAST GOSPEL

037 103 SLOW GOSPEL

038 104 HAWAIIAN

SPANISH/EASTERN EUROPEAN

039 105 PASODOBLE

040 106 CAUCASIAN

041 107 RUSSIAN CHANSON 1

042 108 RUSSIAN CHANSON 2

043 109 POLISH WALTZ

ARABIC/ORIENTAL

044 110 SIRTAKI

045 111 MUS

046 112 ADANI

047 113 BALADI

048 114 KHALIJI

049 115 MALFOOF

Group Name/

Nombre del

grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Rhythm name/

Nombre del ritmo

A-5

Appendix/Apéndice

NOTE

•Sequential number rhythms 171 through 180 do not

sound unless a chord is being played.

•Los ritmos secuenciales números 171 al 180 no

suenan a menos que se ejecute un acorde.

WORLD II

INDIAN

050 116 BHANGRA

051 117 DADRA

052 118 GARBA

053 119 KEHARWA

054 120 DANDIYA

055 121 TEEN TAAL

056 122 BHAJAN

CHINESE

057 123 GUANGDONG

058 124 JIANGNAN

059 125 BEIJING

060 126 DONGBEIYANGGE

061 127 JINGJU

062 128 HUANGMEIXI

063 129 QINQIANG

064 130 YUJU

065 131 YAOZU

066 132 DAIZU

067 133 MIAOZU

068 134 MENGGU

069 135 XINJIANG

070 136 ZANGZU

SOUTHEAST ASIAN

071 137 KRONCONG

072 138 DANGDUT

JAPANESE

073 139 ENKA

BALLAD/PIANO RHYTHMS

BALLAD

001 140 PIANO ROCK BALLAD

002 141 90’S BALLAD

003 142 MODERN BALLAD

004 143 ELECTRIC BALLAD

005 144 SLOW BALLAD 1

006 145 SLOW BALLAD 2

007 146 R&B BALLAD

008 147 16 BEAT BALLAD

009 148 SOUL BALLAD

010 149 POP BALLAD 1

011 150 POP BALLAD 2

012 151 PIANO WALTZ BALLAD

013 152 90’S 6/8 BALLAD

014 153 6/8 BALLAD 1

015 154 6/8 BALLAD 2

016 155 ROCK BALLAD

VARIOUS

017 156 CHRISTMAS SONG

018 157 CHRISTMAS WALTZ

019 158 SCREEN SWING

020 159 SYMPHONY

021 160 STR QUARTET

PIANO RHYTHMS

022 161 PIANO 8 BEAT

023 162 PIANO BALLAD 1

024 163 PIANO BALLAD 2

025 164 EP BALLAD 1

026 165 EP BALLAD 2

027 166 BLUES BALLAD

028 167 JAZZ COMBO 2

029 168 JAZZ COMBO 3

030 169 RAGTIME

031 170 BOOGIE-WOOGIE

032 171 PIANO ROCK & ROLL

033 172 ARPEGGIO 1

034 173 ARPEGGIO 2

035 174 ARPEGGIO 3

036 175 PIANO MARCH 1

Group Name/

Nombre del

grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Rhythm name/

Nombre del ritmo

037 176 PIANO MARCH 2

038 177 STRIDE PIANO

039 178 WALTZ 3

040 179 WALTZ 4

041 180 WALTZ 5

Group Name/

Nombre del

grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Rhythm name/

Nombre del ritmo

NOTA

Appendix/Apéndice

A-6

Music Preset List/Lista de preajustes musicales

Group

Name/

Nombre

del grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Preset Name/

Nombre de preajuste

POPS

1 1 Soft Pop

2 2 Winter Pop

3 3 Oldies Pop

4 4 Alpine Flora

55Gypsy

6 6 Rain Pop

7 7 Movie Waltz

8 8 Blowin’ in

9 9 Funky Rspct

10 10 Love Pop

11 11 Loco

12 12 Rising Sun

13 13 Believer

14 14 Pop Ska

15 15 Weep Blues

16 16 Sugar Pop

17 17 JoyWorldPop

18 18 My Life

19 19 Ribbon

20 20 Blue Love

21 21 Xmas Pop

22 22 Close

23 23 Going On

24 24 70’s Pop

25 25 West Coast

26 26 Bossa Pop

27 27 Radio Pop

28 28 Crazy Roll

29 29 Ivory Pop

30 30 UK Pop

31 31 Breath You

32 32 A Feeling

33 33 Calling

34 34 Take On

35 35 The World

36 36 PlaceOnEarth

37 37 Mexican Pop

38 38 Guitar Pop

39 39 W Up

40 40 Sign

41 41 Wonder

42 42 Hips D Lie

43 43 Say Right

44 44 MdrnPopRock

ROCK

45 45 Rock Clock

46 46 Johnny

47 47 Heartache

48 48 EP R&R

49 49 Pop R&B

50 50 60’s Rock 1

51 51 60’s Rock 2

52 52 60’s Rock 3

53 53 60’s Rock 4

54 54 60’s Rock 5

55 55 Get Rock

56 56 Honky Rock

57 57 Wild Rock

58 58 Alligator

59 59 The Tiger

60 60 Pop Rock

61 61 16Bt Rosa

62 62 Heat Up

63 63 Hard Rock

64 64 Grunge Rock

65 65 Latin Rock

66 66 Hanging By

67 67 R&R

68 68 Piano R&R

69 69 Blues

70 70 8 Bars Blues

71 71 Riff Rock 1

72 72 Riff Rock 2

73 73 Riff Rock 3

DANCE

74 74 Disco Freak

75 75 Funky Clavi

76 76 Earth Disco

77 77 70’s Disco

78 78 Disco Lady

79 79 Staying

80 80 Upside

81 81 80’s Disco

82 82 Give You Up

83 83 Bb Girl

84 84 Blv Disco

85 85 Lady M

86 86 Out Of My H

87 87 Euro Pop

88 88 Don’t Funk

89 89 Trance

90 90 The Escape

JAZZ

91 91 Wonderland

92 92 My Swing

93 93 Things

94 94 Angel

95 95 Time

96 96 Leaf

97 97 Blackbird

98 98 Dolphin

99 99 Roses

100 100 Steps

101 101 RhythmChange

102 102 Swing Mood

103 103 The Mood

104 104 Brown Jug

105 105 Lullaby

106 106 Night

107 107 Street

108 108 Doll

109 109 Someday

110 110 Mode Jazz

111 111 Train

112 112 Tea Time

113 113 Jazz Waltz

114 114 Home

115 115 Blues in F

116 116 Blues in Bb

117 117 Blues in C

118 118 II-V

119 119 II-V-I

120 120 Minor Blues

CLASSIC

1 121 Canon

2 122 Air G String

3 123 Je Te Veux

4 124 Adagio

5 125 Spring

6 126 Ave Maria

7 127 JesusBleibet

8 128 Symphony 25

9 129 Symphony 40

10 130 HungriaDance

11 131 Eine Kleine

12 132 Pathetique

13 133 Moonlight

14 134 PstlSymphony

15 135 Ode To Joy

16 136 Le Cygne

17 137 Swan Lake

18 138 Valse Fleurs

19 139 Habanera

20 140 Nocturne

21 141 Etude

22 142 FrenchCancan

23 143 FantaisieImp

24 144 Humoresque

25 145 Pavane

26 146 Hope & Glory

27 147 Moldau

28 148 FromNewWorld

29 149 Reverie

Group

Name/

Nombre

del grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Preset Name/

Nombre de preajuste

A-7

Appendix/Apéndice

30 150 Nutcracker

31 151 Liebestraume

32 152 Gymnopedies

33 153 Jupiter

34 154 Entertainer

35 155 MapleLeafRag

TRAD

36 156 Michael Row

37 157 GrndpasClock

38 158 Troika

39 159 AuldLangSyne

40 160 Aloha Oe

41 161 O Sole Mio

42 162 Furusato

43 163 SzlaDziweczk

44 164 Battle Hymn

45 165 Condor

46 166 ScarboroFair

47 167 Danny Boy

48 168 Greensleeves

49 169 Annie Laurie

50 170 AmazingGrace

51 171 WeWishU Xmas

52 172 Silent Night

53 173 Joy To World

54 174 YankeeDoodle

55 175 Clarnt Polka

56 176 TaRaRaBoom

57 177 Double Eagle

58 178 Blauen Donau

59 179 Yellow Rose

60 180 BeautDreamer

LATIN

61 181 Moon Bossa

62 182 Your Smile

63 183 Rio

64 184 Bossa Blue

65 185 One Note

66 186 Wave Bossa

67 187 Out Of Tune

68 188 Quiet Star

69 189 Insentive

70 190 Brzl Samba

71 191 Orpheus

72 192 Tico-Tico

73 193 Beguine

74 194 Amapola

75 195 La Paloma

76 196 Banana Boat

77 197 Peanut

78 198 Coffee

79 199 Jamaica

80 200 MoreBeguine

81 201 The No.5

82 202 Everyday

83 203 Mucho

84 204 El Tango

85 205 El Choclo

86 206 Sheriff

87 207 No Woman

88 208 Can’t Help

89 209 Livin’

90 210 Whenever

COUNTRY

91 211 This Land

92 212 My Sunshine

93 213 Walk Line

94 214 Home Roads

95 215 A Friend

96 216 Cowboy

97 217 Still One

98 218 Breath

99 219 CountryWaltz

100 220 He Cheats

BALLAD

1 221 Love Ballad

2 222 R&B Ballad

3 223 Soul Ballad

4 224 Blues Ballad

5 225 MovieBallad1

6 226 MovieBallad2

Group

Name/

Nombre

del grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Preset Name/

Nombre de preajuste

7 227 Xmas Ballad

8 228 Love Me

9 229 Oldies Bld 1

10 230 Oldies Bld 2

11 231 Oldies Bld 3

12 232 Oldies Bld 4

13 233 E World

14 234 Tears

15 235 Moon Waltz

16 236 A’s Theme

17 237 Paradise

18 238 60’s Ballad1

19 239 60’s Ballad2

20 240 Whiter Shade

21 241 FrenchBallad

22 242 Everywhere

23 243 Wonderful

24 244 70’s Ballad1

25 245 70’s Ballad2

26 246 My Song

27 247 Bridge

28 248 Img Ballad

29 249 Without

30 250 Not In Love

31 251 Soft Ballad

32 252 We Were

33 253 Minor Ballad

34 254 Pop Ballad 1

35 255 Pop Ballad 2

36 256 PianoBallad1

37 257 PianoBallad2

38 258 Musical Bld

39 259 R Ballad

40 260 Always Mind

41 261 Endless

42 262 80’s Ballad1

43 263 80’s Ballad2

44 264 80’s Ballad3

45 265 80’s Ballad4

46 266 Friends For

47 267 Rock Ballad

48 268 Eternal

49 269 Everything

50 270 Save Best

51 271 Of The Road

52 272 I Always

53 273 New World

54 274 Vision

55 275 I Can Fly

56 276 Wind Ballad

57 277 Love To You

58 278 My Ballad

59 279 Beautiful

60 280 Scrubs

61 281 Falling

62 282 BlngTogether

63 283 B Day

64 284 Rap Ballad

65 285 Dance Ballad

66 286 MdrnRock Bld

67 287 Slow Ballad

68 288 Kiss Rose

JAZZ BALLAD

69 289 Summer

70 290 New York

71 291 B & S

72 292 L Alone

73 293 Foggy

74 294 Moon Swing

75 295 Foolish

76 296 Valentine

77 297 Midnight

78 298 Journey

79 299 Star

80 300 Starlight

Group

Name/

Nombre

del grupo

Group

Number/

Número de

grupo

Sequential

Number/

Número

secuencial

Preset Name/

Nombre de preajuste

Appendix/Apéndice

A-8

Fingered 1, Fingered 2 Chords/

Acordes Fingered 1, Fingered 2

Fingered 3, Full Range Chords/

Acordes Fingered 3, Full Range

In addition to the chords that can be fingered with

Fingered 1 and Fingered 2, the following chords also

are recognized.

Además de los acordes que se pueden digitar con

Fingered 1 y Fingered 2, también se pueden reconocer

los siguientes acordes.

NOTE

•With Fingered 3, the lowest note fingered is

interpreted as the base note. Inverted forms are not

supported.

•With Full Range Chord, when the lowest fingered is

a certain distance from the neighboring note, the

chord is interpreted as a fraction chord.

•Unlike Fingered 1, 2, and 3, Full Range Chord

requires pressing of at least three keys to form a

chord.

•Con Fingered 3, la nota más baja digitada se

interpreta como nota base. No se pueden usar

formas invertidas.

•Con Full Range Chord, cuando la nota digitada más

baja se encuentre a cierta distancia de la nota

adyacente, el acorde se interpreta como un acorde

bitonal.

•A diferencia de Fingered 1, 2, y 3, Full Range Chord

requiere la pulsación de tres teclas como mínimo

para formar un acorde.

Fingering Guide/

Guía de digitación

*1 With Fingered 2, interpreted as Am7.

*2 With Fingered 2, interpreted as Am7b5.

*3 Inverted form not supported in some cases.

*1 Con Fingered 2, se interpreta como Am7.

*2 Con Fingered 2, se interpreta como Am7b5.

*3 En algunos casos no se puede usar de forma

invertida.

Cdim

Caug *3

Csus4 *3

Csus2 *3

Cmadd9

CmM7

Cdim7 *3

C69 *3

C6 *1 *3

Cm6 *2 *3

Cm7 *3

CM7

Cm7

5 *3

C7sus4

Cadd9

5 *3

Ddim

Fm7

Gm7

add9

    

    

NOTA

A-9

Appendix/Apéndice

Chord Example List/Lista de ejemplos de acordes

Root

Chord

Type

dim

aug

sus4

sus2

m7b

7sus4

add9

madd9

mM7

dim7

(A#)/BbBF#/(Gb)G(G#)/AbAFCC

#/(Db)D(D#)/EbE

•Since the chord input range is limited, this model may not support some of the chords shown above.

•Debido a que el rango de entrada de acordes es limitado, es posible que este modelo no admita algunos de los acordes mostrados arriba.

Function Transmitted Recognized Remarks

Basic

Channel

1 - 16

Default

Changed

Note

Number

0 - 127 0 - 127

0 - 127*1True voice

Program

Change

0 - 127:True #

After

Touch

Control

Change

Pitch Bender

System Exclusive

Key’s

Ch’s

Velocity

9nH v = 1 - 127

8nH v = 64

9nH v = 1 - 127

9nH v = 0, 8nH v =**

Note ON

Note OFF

Mode

Mode 3

Default

Messages

Altered

System

Common

: Song Pos

: Song Sel

: Tune

Aux

Messages

Remarks

: All sound off

Reset all controller

: Local ON/OFF

: All notes OFF

: Active Sense

: Reset

System

Real Time

: Clock

: Commands

0,32

6, 38

100, 101

Bank select

Modulation

Portamento Time

Data entry LSB, MSB*2

Volume

Pan

Expression

DSP Parameter0*2

DSP Parameter1*2

DSP Parameter2*2

DSP Parameter3*2

Damper

Portamento Switch

Sostenuto

Soft pedal

Vibrato rate

Vibrato depth

Vibrato delay

DSP Parameter4*2

DSP Parameter5*2

DSP Parameter6*2

DSP Parameter7*2

Portamento Control

Reverb send

Chorus send

RPN LSB, MSB*2

Model PX-330 Version : 1.0

Mode 1 : OMNI ON, POLY

Mode 3 : OMNI OFF, POLY

Mode 2 : OMNI ON, MONO

Mode 4 : OMNI OFF, MONO

O : Yes

X : No

MIDI Implementation Chart

** : no relation

** : sin relación

*1 : Depends on tone

*2 : For details, see MIDI Implementation at http://world.casio.com/.

*1 : Depende del tono

*2 : Si desea más información, vea Implementación MIDI en http://world.casio.com/.

This recycle mark indicates that the packaging conforms to

the environmental protection legislation in Germany.

Esta marca de reciclaje indica que el empaquetado se

ajusta a la legislación de protección ambiental en Alemania.

MA1106-B Printed in China

PX330ES1B

Casio Px 330 Users Manual PX330_e

Web-Px330E1B web-px330e1b

px-330 to the manual 69769c90-7fb0-442e-9487-3d4a76a12249

PX330 PX330_EN PX-330 | Electronic Musical Instruments | Manuals | CASIO

Navigation menu

Versions of this User Manual:

Views

Navigation