Casio Watch 2115 Users Manual QW 1950/2115
2115 to the manual 4be97a3d-e50b-44ea-8531-d46fe766feab
2015-01-21
: Casio Casio-Casio-Watch-2115-Users-Manual-244039 casio-casio-watch-2115-users-manual-244039 casio pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Module No. 1950/2115 1950/2115-1 GENERAL GUIDE • Press C to change from mode to mode. • After you perform an operation in any mode, pressing C returns to the Timekeeping Mode. • If you do not press any button for a few minutes while making settings in any mode (indicated when settings are flashing), the watch automatically clears the setting screen (settings stop flashing) and returns to the normal display for the mode you are in. • This watch returns to the Timekeeping Mode whenever you hold down the C button for one or two seconds. If you ever lose track of what mode you are in or what you should do next, hold down C to return to normal timekeeping. The operational procedures for Modules 1950 and 2115 are identical. All of • In any mode press L to illuminate the display. the illustrations in this manual show Module 1950. Countdown Alarm Mode Timekeeping Mode [Module 2115] Alarm Mode Dual Time Mode [Module 1950] TIMEKEEPING MODE To set the time and date PM indicator 1. Hold down A while in the Timekeeping Mode until the seconds digits flash on the display because they are selected. 2. Press C to change the selection in the following sequence. Day of week Month - Day Seconds Minutes Hour 12/24-Hour Format Day of week Hour Stopwatch Mode Day Month Seconds Minutes 3. While the seconds digits are selected (flashing), press D to reset the seconds to 00. If you press D while the seconds count is in the range of 30 to 59, the seconds are reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the minutes count is unchanged. 4. While any other digits (beside seconds) are selected (flashing), press D to increase the number or B to decrease it. While the 12/24-hour format setting is selected, press D or B to toggle it between 12 and 24. While the day of the week is selected (flashing), press D to advance to the next day or B to return to the previous day. • Except for when adjusting the seconds or setting the 12/24-hour format, holding down a button changes the current selection at high speed. • When the 12-hour format is selected, the indicator P appears on the display to indicate “P.M.” times. There is no indicator for “A.M.” times. • When the 24-hour format is selected, the indicator 24 appears on the display. 5. After you set the time and date, press A to return to the Timekeeping Mode. • The auto light switch indicator is shown on the display in all modes while the auto light switch function is on. • In order to protect against running down the battery, the auto light switch function is automatically turned off approximately three hours after you turn it on. Repeat the above procedure to turn the auto light switch function back on if you want. • Pressing L while in the Timekeeping Mode illuminates the display, regardless of the auto light switch’s on/off setting. Caution • The backlight of this watch employs an electro-luminescent (EL) light, which loses its illuminating power after very long term use. • Frequent use of the backlight shortens the battery life. • The watch emits an audible sound whenever the display is illuminated. This is because the EL light vibrates slightly when lit. It does not indicate malfunction of the watch. Warning! • Never try to read your watch when mountain climbing or hiking in areas that are dark or in areas with poor footing. Doing so is dangerous and can result in serious personal injury. • Never try to read your watch when running where there is the danger of accidents, especially in locations where there might be vehicular or pedestrian traffic. Doing so is dangerous and can result in serious personal injury. • Never try to read your watch when riding on a bicycle or when operating a motorcycle or any other motor vehicle. Doing so is dangerous and can result in a traffic accident and serious personal injury. • When you are wearing the watch, make sure that its auto light switch function is turned off before riding on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended operation of the auto light switch can create a distraction, which can result in a traffic accident and serious personal injury. COUNTDOWN ALARM MODE Progress beeper on indicator The countdown alarm can be set within a range of 1 second to 24 hours. When the countdown reaches zero, an Auto repeat on indicator alarm sounds for 10 seconds or until you press any button. ABOUT THE BACKLIGHT Current time About the Auto Light Switch Function To set the countdown start time When the auto light switch function is turned on, the backlight automatically turns on for two seconds under the conditions described below. Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light switch to operate when not needed, which shortens battery life. 1. Hold down A while in the Countdown Alarm Mode. The hours digits flash on the display because they are selected. 2. Press C to change the selection in the following sequence. Moving the watch to a position that is parallel to the ground and then tilting it towards you approximately 40 degrees causes the backlight to illuminate. Minutes 40° Parallel to ground • The backlight may not illuminate if the face of the watch is more than 15 degrees off parallel to the left or right. Make sure that the back of your hand is parallel to the ground. Parallel to ground More than 15 degrees too high More than 15 degrees too low • Static electricity or magnetic force can interfere with proper operation of the auto backlight function. If the auto backlight does not illuminate, try moving the watch back to the starting position (parallel with the ground) and then tilt it back toward you again. If this does not work, drop your arm all the way down so it hangs at your side, and then bring it back up again. • Under certain conditions the backlight may not light until about one second or less after turning the face of the watch towards you. This does not necessarily indicate malfunction of the backlight. To switch the auto light switch function on and off In the Timekeeping Mode, hold down B for one or two seconds to turn the auto light switch function on and off. Auto light switch indicator Hold down B . ON OFF 1/10 Seconds Seconds Hour Minutes Seconds Mode indicator 3. Press D to increase the selected number or B to decrease it. Holding down either button changes the selection at high speed. • Press D and B at the same time to clear the starting time to 0:00' 00". • To set the starting value of the countdown time to 24 hours, set 0:00' 00". 4. After you set the countdown start time, press A twice to return to the Countdown Alarm Mode. To use the countdown alarm 1. Press D while in the Countdown Alarm Mode to start the countdown alarm. 2. Press D again to stop the countdown alarm. • You can resume countdown alarm operation by pressing D . 3. Stop the countdown alarm and then press B to reset the countdown time to its starting value. • When the end of the countdown is reached and auto repeat timing is off, the alarm sounds for 10 seconds or until you stop the alarm by pressing any button. Countdown timing stops and the countdown time is automatically reset to its starting value after the alarm stops. To switch auto repeat timing and the progress beeper on and off 1. Hold down A while in the Countdown Alarm Mode. The hour digits flash on the display because they are selected. Press A again to move the flashing to the auto repeat ON/OFF setting. 2. Press D or B to toggle auto repeat on ( ) and off. 3. Press C to move the flashing to the progress beeper ON/OFF setting. 4. Press D or B to toggle the progress beeper on ( ) and off. 5. Press A to return to the Countdown Alarm Mode. • When the end of the countdown is reached while auto repeat is on, the alarm sounds, but the countdown restarts from the beginning without stopping. You can stop the countdown by pressing D and manually reset to the start time by pressing B. • If you set a starting time of 10 seconds or less and have Auto Repeat turned on, the countdown alarm tone (which normally sounds for 10 seconds) sounds for only one second. • When the progress beeper is turned on, the watch beeps as the countdown time passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20, 10, 5, 4, 3, 2, and 1-second marks. 1950/2115-2 STOPWATCH MODE Target time on indicator Current time ALARM MODE The Stopwatch Mode lets you measure elapsed time, split times, and two finishes. The range of the stopwatch is 23 hour, 59 minutes, 59.99 seconds. You can also have an alarm sound when a target time is reached. The Stopwatch Mode also features an Auto-Start function. Alarm on indicator When the Daily Alarm is switched on, the alarm sounds Hourly time signal on indicator Current time for 20 seconds at the preset time each day. Press any button to stop the alarm after it starts to sound. When the Hourly Time Signal is on, the watch beeps every hour on the hour. To set the alarm time Minutes 1. Hold down A until the hour digits start to flash on the display. The hour digits flash because they are selected. • This operation will switch the Daily Alarm on automatically. 2. Press C to change the selection in the following sequence. 1/100 Seconds Seconds Hour Mode indicator (a) Elapsed time measurement Start Stop Re-start Stop Clear Split release Stop Clear (b) Split time measurement Start Split Hour Minutes 3. Press D to increase the selected digits and B to decrease them. Holding down either button changes the selection at high speed. • The format (12-hour and 24-hour) of the alarm time matches the format you select for normal timekeeping. • When setting the alarm time using the 12-hour format, take care to set the time correctly as morning (no indicator) or afternoon (P). 4. After you set the alarm time, press A to return to the Alarm Mode. To turn the daily alarm and hourly time signal on and off Press B while in the Alarm Mode to change the status of the daily alarm and hourly time signal in the following sequence. (c) Split time and 1st-2nd place times Start Minutes Mode indicator Split Stop Split release First runner finishes. Second runner finishes. Record time of first runner. Record time of second runner. Clear Both OFF About the Auto-Start function Daily Alarm Only Hourly Time Signal Only Both ON With the Auto-Start function, the watch performs a 5-second countdown. When the countdown reaches zero, stopwatch operation starts automatically. During the final three seconds of the countdown, a beeper sounds with each second. • The alarm on indicator ( ) and the Hourly Time Signal on indicator ( on the display in all modes while these functions are turned on. To turn the Auto-Start function on and off While the display is showing all zeros in the Stopwatch Mode, press B to toggle it on and off. • The indicator AUTO-ST appears and 05 is shown in the upper display while AutoStart is turned on. The AUTO-ST indicator is not shown and the upper part of the display shows the current time when Auto-Start is turned off. To test the alarm sound Hold down B while in the Alarm Mode to sound the alarm. • Note that pressing B also changes the alarm and the hourly time signal ON/OFF settings. DUAL TIME MODE About the Target Time function With the Target Time function, an alarm sounds for ten seconds whenever the time being kept by the stopwatch reaches a target time you have preset. Current time To set the Target Time and to turn it on and off 1. While the display is showing all zeros in the Stopwatch Target time on indicator Mode, hold down A , and the hour digit of the target Hour time starts to flash because it is selected. 2. Press C to change the selection in the following sequence. Hour ) are shown Minutes 3. Press D to increase the selected number or B to decrease it. Holding down either button changes the se0:00' 00". 4. Press A to move the flashing to the target time ON/OFF setting. 5. D or B to toggle the target time on and off. 6. Press A to return to the Stopwatch Mode. Important! The alarm will not sound if you do not turn on the target time. • Press A , C or L to stop the alarm after it starts to sound. To set the Dual Time 1. Hold down A while in the Dual Time Mode. The hour digits flash on the display because they are selected. 2. Press C to change the selection in the following sequence. Seconds Minutes Seconds lection at high speed. • Press D and B at the same time to clear the setting to Mode indicator The Dual Time Mode lets you keep track of the time in another time zone. You can also select the timekeeping format (12-hour or 24-hour) separately from the Timekeeping Mode. Hour Hour Minutes Minutes Mode indicator 3. Press D to increase the selected digits and B to decrease them. Holding down either button changes the selection at high speed. 4. After you set the time, press A to return to the Dual Time Mode. • In the Dual Time Mode, the seconds count is synchronized with the seconds count of the Timekeeping Mode. • In the Dual Time Mode, press B to toggle between the 12-hour and 24-hour formats.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Create Date : 2000:08:28 14:14:20 Producer : Acrobat Distiller 4.0.5 for Macintosh Keywords : WAT Subject : Creator : Adobe PageMaker 6.52 Title : QW-1950/2115 Author : MAS Modify Date : 2000:09:18 18:38:22+09:00 Page Count : 2 Page Mode : UseThumbs Page Layout : OneColumnEXIF Metadata provided by EXIF.tools