Casio Watch 2299 Users Manual QW 2169/2299

2299 to the manual eba8db75-52f8-47ad-bf4c-192030e3eeb8

2015-01-21

: Casio Casio-Casio-Watch-2299-Users-Manual-244058 casio-casio-watch-2299-users-manual-244058 casio pdf

Open the PDF directly: View PDF .
Page Count: 2

2169/2299-1

TIMEKEEPING MODE

This section provides information on setting the time and date.

•In the Timekeeping Mode, press BB

B to switch between the day of the week and month screens.

•In the Timekeeping Mode, press EE

E to illuminate the display for about three seconds.

•In the Timekeeping Mode, press DD

D to switch between the 12-hour and 24-hour formats.

•When the 12-hour format is selected, “p.m.” times are indicated on the display by P, while

“a.m.” times are indicated by A. No indicators are used with the 24-hour format.

•The graphic area of the Timekeeping Mode screens shows patterns that indicate the pas-

sage of seconds.

•Various animated figures move in the animation area as seconds pass in the Timekeeping

Mode. At 00 and 30 seconds, a high-speed animated graphic appears.

To set the time and date

1. Hold down AA

A while in the Timekeeping Mode until the seconds digits start to flash on the

display. The seconds flash because they are

selected

2. Press CC

C to change the selection in the following sequence.

Seconds

Day

Hour Minutes

YearMonth

3. While the seconds digits are selected (flashing), press DD

D to reset the seconds to 00.

•If you press DD

D while the seconds count is in the range of 30 to 59, the seconds are reset to

00 and 1 is added to the minutes. If the seconds count is in the range of 00 to 29, the

minutes count is unchanged.

4. While any other digits (besides seconds) are selected (flashing), press DD

D to increase the

number. Holding down DD

D changes the current selection at high speed.

5. After you set the time and date, press AA

A to return to the Timekeeping Mode.

•The day of the week is automatically set in accordance with the date.

•The date can be set within the range of January 1, 2000 to December 31, 2039.

•If you do not operate any button for a few minutes while a selection is flashing, the flashing

stops and the watch goes back to the Timekeeping Mode automatically.

DST (Daylight Saving Time)

Daylight Saving Time (DST) automatically advances the time setting by one hour from Stan-

dard Time. Whether you should use Daylight Saving Time depends on the geographic area

where you are currently located.

To switch between Standard Time and Daylight Saving Time

In the Timekeeping Mode, hold down BB

B for about two seconds until

the watch beeps twice.

•The colon between the hour and minutes digits flashes while Day-

light Saving Time is selected.

Month ScreenDay of the week Screen

Day of week – Day

Month – Day

Animation area

Graphic area

Press BB

PM indicator

Hour : Minutes

Seconds

Flashing

Graphic area

Mode indicator – Timer No.

Seconds

Minutes

1/10 second

Indication More than Less than Time Up

5 minutes 5 minutes

Graphic Area

Indication Start 5'00"0 Time Up

Beep 1 second 1 second 10 seconds

Backlight 1 second 1 second 2 seconds

COUNTDOWN ALARM MODE

The Countdown Alarm Mode has three 60-minute timers whose start-

ing time can be set in one-minute increments. When the countdown

reaches zero, an alarm sounds.

•In the Countdown Alarm Mode, press BB

B to illuminate the display

for about three seconds. To illuminate the display while setting

the countdown time (while the minutes digits are flashing), press

•The starting times of the countdown timers are preset to 15, 30,

and 60 minutes when you purchase it. You can use these settings

as they are, or you can change to different starting times if you

want.

BACKLIGHT

A backlight that uses an EL (electro-luminescent) panel causes the entire display to glow for

easy reading in the dark. Depending on the mode, pressing EE

E or BB

B turns on the backlight for

about three seconds. See the sections that cover each mode for information on whether you

should press EE

E or BB

•The backlight of the watch employs an electro-luminescent (EL) light, which loses illuminat-

ing power after very long use.

•The illumination provided by the backlight may be hard to see when viewed under direct

sunlight.

•The watch will emit an audible sound whenever the display is illuminated. It does not indicate

malfunction of the watch.

•The backlight automatically turns off whenever an alarm sounds.

To use a countdown timer

1. Press DD

D while in the Countdown Alarm Mode to select the timer whose time you want to

use.

Timer 1 Timer 3Timer 2

•Pressing DD

D does not change the timer selection if a countdown timer operation is currently in

progress or is paused. You must stop the ongoing countdown operation before you can change

to another timer.

2. Press EE

E to start the countdown timer.

•When the countdown reaches zero, an alarm sounds for 10 seconds or until you stop the

alarm by pressing any button. The countdown time is automatically reset to its starting value

after the alarm stops.

•Press EE

E while a countdown operation is in progress to pause it. Press EE

E again to resume the

countdown.

•To completely stop a countdown operation, first pause it (by pressing EE

E), and then press DD

This returns the countdown time to its starting value.

To change a countdown time

1. Press DD

D while in the Countdown Alarm Mode to select the timer whose time you want to

change.

2. After you select a timer, hold down AA

A until the minutes digits start to flash on the display.

3. Press DD

D to increase the minutes. Holding down DD

D changes the minutes at high speed.

4. After you set the countdown time, press AA

A to return to the Countdown Alarm Mode.

•If you do not operate any button for a few minutes while a selection is flashing, the flashing

stops and the watch goes back to the Countdown Alarm Mode automatically.

About countdown indicators

An audible beep, the EL backlight, and the graphic area on the display keep you informed

about the progress of the countdown as noted in the following table.

Module No. 2169/2299

GENERAL GUIDE

•Press CC

C to change from mode to mode.

•The animation area shows different animated characters and graphics, depending on the mode and the operation being performed.

•The operational procedures for Module 2169 and 2299 are identical. All of the illustrations in this manual show Module 2169.

Stopwatch Mode Alarm Mode

Timekeeping Mode Countdown Alarm Mode

Animation area

[Module 2299] [Module 2169]

Press CC

2169/2299-2

Auto-start indicator

Alarm on indicator

Graphic area

Alarm 2 (off)

Alarm 5 (off)

Alarm 1

(on)

Alarm 4 (off)

Alarm 3 (on)

Seconds

Minutes

1/100 second

Mode indicator Mode indicator – Alarm No.

Graphic area

Alarm on indicator

AM indicator

Hour : Minutes

STOPWATCH MODE

The Stopwatch Mode lets you measure elapsed time, split times,

and two finishes. You also get Auto-Start function. The range of the

stopwatch is 59 minutes, 59.99 seconds.

•In the Stopwatch Mode, press BB

B to illuminate the display for about

three seconds.

To measure elapsed time

1. Press EE

E to start the stopwatch.

2. Press EE

E to stop the stopwatch.

•You can resume the measurement operation by pressing EE

E again.

3. Press DD

D to clear the stopwatch to all zeros.

To record split times

1. Press EE

E to start the stopwatch.

Press

to display the timing up to that point. Stopwatch timing continues internally.

3. Press DD

D to clear the split time and to continue time measurement on the display.

•You can repeat steps 2 and 3 as many times as you want.

4. Press EE

E to stop the time measurement.

5. Press DD

D to clear the stopwatch to all zeros.

To time first and second place finishes

1. Press EE

E to start the stopwatch.

2. Press DD

D when the first finisher crosses the line, and record the time.

3. Press EE

E when the second finisher crosses the line.

4. Press DD

D to display the finishing time of the second finisher.

5. Press DD

D again to clear the stopwatch to all zeros.

About the Auto-Start function

With the Auto-Start function, the watch performs a 5-second countdown. When the countdown

reaches zero, stopwatch operation starts automatically. During the final three seconds of the

countdown, a beeper sounds with each second.

To use the Auto-Start function

1. While the stopwatch display is showing all zeros (00'00"00) in

the Stopwatch Mode, press DD

•At this time the auto-start indicator appears on the display to indi-

cate that auto-start is on. Press DD

D again to turn auto-start off (in-

dicated when the auto-start indicator is not on the display).

2. Press EE

E to start the countdown.

•Pressing EE

E also causes the countdown time to appear on the

display.

•When the countdown reaches zero, a tone sounds, the backlight illuminates the display, and

a stopwatch timing operation starts automatically.

•To stop the Auto-Start countdown and return to the all-zeros display, press DD

•Pressing EE

E while the Auto-Start countdown is in progress immediately starts the stopwatch.

To set an alarm time

1. Press DD

D while in the Alarm Mode to select the alarm whose time you want to set.

Alarm 1 Alarm 4

Alarm 5

Alarm 2 Alarm 3

Hourly Time Signal

2. After you select an alarm, hold down AA

A until the hour digits start to flash on the display. The

hour digits flash because they are

selected

•This operation automatically turns on the alarm.

3. Press CC

C to change the selection in the following sequence.

Hour Minutes

4. Press DD

D to increase the selected digits. Holding down DD

D changes the selection at high

speed.

•The format (12-hour and 24-hour) of the alarm time matches the format you select for normal

timekeeping.

•When setting the alarm time using the 12-hour format, take care to set the time correctly as

a.m. (A indicator) or p.m. (P indicator).

5. After you set the alarm time, press AA

A to return to the Alarm Mode.

•If you do not operate any button for a few minutes while a selection is flashing, the flashing

stops and the watch goes back to the Alarm Mode automatically.

To turn an alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, press DD

D to select an alarm or the Hourly

Time Signal.

2. Press BB

B to toggle the select item on and off.

•The indicators ALM and appear on the display whenever

an alarm is turned on.

•The indicators SIG and appear on the display whenever

the Hourly Time Signal is turned on.

•Indicators in the graphic area of the Alarm Mode show which

alarms are turned on.

•In other modes (besides the Alarm Mode), the ALM indicator

remains on the display as long as at least one of the alarms

is on, while the SIG indicator remains on the display while

the Hourly Time Signal is on.

To test the alarm

Hold down BB

B while in the Alarm Mode to sound the alarm.

ALARM MODE

You can set five independent Daily Alarms. When a Daily Alarm is

turned on, the watch beeps for 20 seconds at the alarm time each

day. Press any button to stop the alarm after it starts to sound.

When the Hourly Time Signal is turned on, the watch beeps every

hour on the hour.

•In the Alarm Mode (including alarm time setting), press EE

E to illu-

minate the display for about three seconds.

•The graphic area in the Alarm Mode shows the current on/off sta-

tus of each of the five alarms.

Casio Watch 2299 Users Manual QW 2169/2299

2299 to the manual eba8db75-52f8-47ad-bf4c-192030e3eeb8

Navigation menu

Versions of this User Manual:

Views

Navigation