Casio Dq584 584B DQ 584/584B

DQ-584 DQ584_584B_EN

DQ-584B to the manual dd5f46d9-3a43-4e08-b8d2-581adfd06a63

DQ-584 DQ584_584B_EN DQ-584 | Timepieces (Clocks) | Manuals | CASIO

: Casio Dq584-584B dq584-584b casio pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

MA0507-EA

Operation Guide DQ-584/584B
4 HR (MONTH) button
• Pressing this button while “TM” is selected by the Mode switch 5 advances the hour setting.
• Pressing this button while “CALENDAR” is selected by the Mode switch 5 advances the month setting.

ILLUSTRATION

5 Mode switch
NORMAL: For normal use
AL: For adjusting the alarm setting
TM: For adjusting the time setting
CALENDAR: For adjusting the date setting
6 Alarm Mode selector
SNZ: Snooze alarm on
ON: Alarm on
OFF: Alarm off
7 °C/°F button
Press this button to toggle the temperature units between Celsius and Fahrenheit.
8 Battery

SETTING THE CLOCK

• A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the
clock.
• Depending on the clock model, its configuration may differ somewhat from that shown in the illustration.
Alarm Off
PM indicator

Snooze Alarm On

Current temperature

Current time
(Hour, minutes)

Date
(month – day)

Snooze on indicator

Alarm on indicator

HR (MONTH) or MIN (DATE)
button depressed
Alarm indicator

Alarm time

1. Slide the Mode switch 5 to
“TM”. This causes the current
time to flash on the display.
2. Use the 12 • 24 HR (YEAR)
button 2, MIN (DATE) button
3, and HR (MONTH) button 4
to set the time. Holding down
the MIN (DATE) button 3 or
HR (MONTH) button 4
changes the corresponding
setting at high speed.
• Make sure you set the correct
am/pm time if you are using 12hour timekeeping. The PM
indicator indicates PM times,
while nothing is indicated for AM
times.
• The seconds count reverts to 00
automatically whenever you finish
adjusting the minute setting.
3. Slide the Mode switch 5 to
“CALENDAR”. This causes the
current date to flash on the
display.
4. Use the 12 • 24 HR (YEAR)
button 2, MIN (DATE) button
3, and HR (MONTH) button 4
to set the date. Holding down
any button advances the
corresponding setting at high
speed.
• You can set the year in the range
of 1990 to 2030.

Press to advance the
hour setting.

Press to advance the
minute setting.

Press to toggle between
12-hour and 24-hour
timekeeping.

PM indicator
Hour

Press to advance the
month setting.

Minutes

Press to advance the
day setting.

Press to advance the
year setting.

Year
Month

Day

GENERAL GUIDE
1 SNOOZE/LIGHT button
• Press this button to illuminate the display for about three seconds.
• Pressing this button while the alarm is sounding stops the alarm.

5. Slide the Mode switch 5 to “NORMAL”. This will
cause the figures on the display to stop flashing.

2 12 • 24 HR (YEAR) button
• Press this button to toggle between 12-hour and 24-hour timekeeping.
• Pressing this button while “CALENDAR” is selected by the Mode switch 5 advances the year setting.
3 MIN (DATE) button
• Pressing this button while “TM” is selected by the Mode switch 5 advances the minute setting.
• Pressing this button while “CALENDAR” is selected by the Mode switch 5 advances the day setting.

1

Operation Guide DQ-584/584B
USING THE ALARM

USING THE LIGHT

The alarm sounds when the current time reaches the alarm time. The face illuminates for the first 5 seconds of the
alarm operation as well. The alarm tone alternates between two levels.

Hold down the SNOOZE/LIGHT button 1 to illuminate the display. The light will go out automatically after about
three seconds, even if you keep the button depressed.

You can also use the Alarm Mode selector 6 to select the snooze alarm feature.

Important!

Setting the Alarm Time

Press to advance the

1. Slide the Mode switch 5 to
alarm time hour setting.
“AL”. This causes the alarm time
setting to flash on the display.
2. Use the 12 • 24HR (YEAR)
button 2, MIN (DATE) button
3, and HR (MONTH) button 4
to set the alarm time. Holding
down the MIN (DATE) button 3
or HR (MONTH) button 4
changes the corresponding
setting at high speed.
• Make sure you set the correct
am/pm time if you are using 12hour timekeeping. The PM
indicator indicates PM times,
Hour
while nothing is indicated for AM
times.
3. Slide the Mode switch 5 to “NORMAL”. This will cause
the figures on the display to stop flashing.
4. Turning the Alarm On and Off
Use the Alarm Mode selector 6 on the top of the clock
to turn the alarm on and off, and to select the snooze
feature.

Press to advance the
alarm time minute setting.

• Overuse of the light can shorten battery life.
Press to toggle between
12-hour and 24-hour
timekeeping.

THERMOMETER FUNCTIONS
A built-in sensor measures temperature and shows the measured value on the display.

Temperature Measurements

• The temperature display shows “LO” for temperatures below –19.5°C (–3.0°F) and “HI” for temperatures above
70°C (158°F).
• Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings actually are outside the guaranteed temperature range of this clock.

Switching between Celsius and Fahrenheit

• Push the °C/ °F button 7 to select either Celsius (°C) or Fahrenheit (°F).
Celsius (°C)

Fahrenheit (°F)

Minutes

°C/°F button (7)

BATTERY REPLACEMENT
Replace the battery whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove the old battery.
3. Load a new battery. Make sure that the positive (+) and negative (–) ends of the battery are facing correctly. An
incorrectly loaded battery can burst and damage the clock.
4. Replace the battery compartment cover.

Battery precautions
Alarm Mode selector

Description
The alarm sounds at the preset time for one minute. You can stop the alarm by
pressing the SNOOZE/LIGHT button 1. The snooze feature will cause the alarm to
sound again about five minutes after it stops. A indicator flashes on the display
during the period between alarms.

SNZ

• If you keep stopping the alarm manually by pressing the SNOOZE/LIGHT button 1
The alarm will sound again, about five minutes after you stop it.

• Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician
immediately.
• Be sure to load the battery with its positive (+) and negative (–) ends facing correctly.
• Never charge the battery that comes with the clock.
• Should a battery ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the battery at least once a year, even if the current battery is working properly.
• The battery that comes with the clock loses some power during transport and storage.

• If the alarm is not stopped manually
The alarm will sound three times for one minute, at five-minute intervals. After that the
snooze feature will be cancelled automatically.
ON
OFF

The alarm sounds at the preset time for one minute.
The alarm does not sound.

• The light also turns on for the first five seconds that the alarm sounds.

Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button 1 to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector 6 to OFF.

Testing the alarm

• While the mode switch setting is “NORMAL”, hold down the HR (MONTH) button 4 and MIN (DATE) button 3
at the same time to sound the alarm. All of the display’s digital segments will appear at this time. Release the
buttons to stop the alarm.

2