Cellphone Mate SureCall FLEXPRO Dual-band signal booster for Home and Small office User Manual SureCall Flex Pro User Guide

Download:
Mirror Download [FCC.gov]
Document ID	2184567
Application ID	wwXcS70pC7nFXbQTF6Hyvg==
Document Description	Users Manual v2.1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.49kB (818566 bits)
Date Submitted	2014-02-06 00:00:00
Date Available	2014-03-03 00:00:00
Creation Date	2014-02-06 16:13:31
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-02-06 16:13:31
Document Title	SureCall Flex Pro User Guide
Document Creator	Microsoft® Word 2010
Document Author:	SureCall

Dual-Band Wireless
Adjustable Signal Booster / Kit
INTRODUCTION
THEORY OF OPERATION
SURECALL FLEX PRO PACKAGES
FLEX PRO BOOSTER HARDWARE
SUMMARY AND DESCRIPTION OF
SAFEGUARD FEATURES
SITE SELECTION
INSTALLATION INSTRUCTIONS
TROUBLESHOOTING
FREQUENTLY ASKED QUESTIONS 13
OBTAINING TECHNICAL SUPPORT 13
Flex Pro Booster, Flex Pro
Omni Kit, Flex Pro Panel Kit
(FLEX PRO)
User Guide
WARRANTY
14
SPECIFICATIONS
16
SAFETY INFORMATION
17
INTRODUCTION
Introduction
Congratulations on purchasing the SureCall Flex Pro, the finest cellular signal
booster available!
SureCall adjustable cellular signal boosters and kits from Cellphone-Mate remove
frustrations over dropped calls, limited range, and slow data rates by amplifying incoming
and outgoing cellular signals in buildings, offices, and homes. The Flex Pro is designed
with leading-edge technologies to detect and amplify weak incoming signals your cellular
device would otherwise miss and to broadcast a significantly stronger signal back to the
cell tower.
This guide contains all the information you need to get your SureCall Flex Pro booster
system up and running.
Theory of Operation
The SureCall Flex Pro is a high-quality bidirectional signal booster that boosts cellular
signals for areas prone to weak or shadowed cellular coverage.
The Flex Pro works with two antennas:
 An inside antenna that communicates with your cell phone.
 An outside antenna that communicates with the cell tower.
Signals sent from a cell tower are received by the outside antenna, amplified by the
booster and then sent to your phone via the inside antenna.
When your phone transmits, the signal is sent to the inside antenna, and then sent to
the cell tower via the outside antenna.
Some cell signal is required for the Flex Pro to enhance cellular signal coverage. The
weakest cell signal for the Flex Pro to work is low -100dBm to high -90dBm. dBm is an
abbreviation for the power ratio in decibels of the radio power per one milliwatt.
To measure your existing cell signal on an Apple iPhone, dial *3001#12345#*and
press Call. In the top-left corner, a number appears instead of bars.
For Android devices, you can download several apps to measure exact signal
strength. Look up check real signal strength to find a cell signal measurement app.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 2
INTRODUCTION
SureCall Flex Pro Packages
Flex Pro - Antenna Kitting Information
Component
Product Number
(Description)
Outdoor
Antennas*
Outdoor Cables*
Indoor Antennas*
Indoor Cables*
Gain/Loss
800 MHz
1900 MHz
CM288W
3 dBi
4 dBi
CM100-L
5 dBi
7 dBi
CM100-S
4 dBi
5 dBi
CM230W
10 dBi
10 dBi
CM240-40FN (40 feet)
–3.98 dB
–6.52 dB
CM400-65NN (65 feet)
–3.89 dB
–5.43 dB
CM248W
7 dBi
10 dBi
CM222W
3 dBi
6 dBi
CM240-20FN (20 feet)
–2.29 dB
–3.56 dB
CM400-40NN (40 feet)
–2.63 dB
–3.57 dB
Notes
65 feet or longer
* All equivalent antennas and cables are suitable for use with the Flex Pro booster.
Note: For the signal booster to work, the following items are required:






Outside antenna
Cable for connecting the outside antenna to the booster
Signal booster
Inside antenna
Cable for connecting the inside antenna to the booster
Power supply
Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by
FCC new rules. Please contact FCC for details: 1-888-CALL-FCC.
Changes or modifications not expressly approved by Cellphone-Mate could void the
user’s authority to operate the equipment.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 3
INTRODUCTION
Flex Pro Booster Hardware
The following figure shows the key hardware components on the Flex Pro cellular
signal booster. Refer to this figure as you install your SureCall Flex Pro components.
Outdoor Antenna
Connector (not shown)
Alert
LED
Power
LED
Alert
LED
Cellular800 Dial
PCS1900 Dial
Digital Interface
Indoor Antenna
Connector
Power Connector
Summary and Description of Safeguard Features
This device is equipped with all the safeguard features required by FCC new rules to
ensure no interference is created to affect the cell tower: AGC, automatic shutdown,
Dual RSSI monitoring, automatic silence, and more.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 4
INSTALLATION
Unpack all package contents and check for damage. For missing or damaged
items, contact your reseller. Keep the carton and packing material to store the
product or if you need to return it.
Site Selection
For optimum performance, select a location for your booster that:
 Provides the best signal strength possible. To measure your existing cell
signal on an Apple iPhone, dial *3001#12345#*and press Call. In the topleft corner, a number appears instead of bars. For Android devices, you can
download several apps to measure exact signal strength. Look up “check
real signal strength“ to find a cell signal measurement app.
 Avoids areas where wireless signals can be blocked or reflected by
buildings, walls, trees, hills, and other terrain features. This can result in
low signal strength.
 Is not close to energy-efficient windows, which can affect signal penetration
into a home or office.
Note: The cell phone tower site in relation to the location where you install your
booster also determines signal strength. Although cell phone providers try to place
towers for maximum coverage, local ordinances and terrain features can restrict
tower locations, which can limit signal strength at your location.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 5
INSTALLATION
Installation Instructions
The Flex Pro signal booster is suited for installation in a building or home.
Step 1. Connect the Outside Antenna
1.
Mount the fiberglass antenna in an outside mounting location that:
 Has at least a 12-inch radius clear of obstructions and other radiating
elements.
 Is at least 75 feet in a straight line from the inside antenna when used in an
area prone to weak cellular signals and operating the booster at full 65dB
gain.
 Is not co-located or operating with any other antenna or booster.
2.
Using the CM240 or CM400 cable, connect the outside antenna to the booster
connector marked OUTSIDE (see page 4).
3.
Hand tighten the connection.
Step 2. Connect the Inside Antenna
1.
Mount the inside antenna:
 Omnidirectional dome antenna: mount the antenna on the ceiling in a
central location where you want reception.
 Panel antenna: install the antenna against a wall or surface projecting
where you want reception.
2.
Using the CM240 or CM400 cable, connect the inside antenna to the booster
connector marked INSIDE (see page 4).
3.
Hand tighten the connection.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 6
INSTALLATION
Note: With a signal booster kit with panel antenna, stay 6½ feet from the panel
based on new FCC rules.
Step 3. Mount the Booster (Optional)
1.
Select a location for your booster.
2.
Clean the intended surface and allow it to dry.
3.
Peel the protective paper from the back of the hook sides of the Velcro. Press
the adhesive side of the Velcro strips into place on the bottom of the booster,
one strip on each end.
4.
Wait 5 minutes, and then attach the loop side of the Velcro to the hook side.
The adhesive bond reaches maximum strength after 24 hours.
5.
With both the Velcro loop and hook pieces attached to the back of the booster,
peel the protective paper off of the back of the loop strips.
6.
Press the entire booster into its mounting place, and then wait 5 minutes for
the adhesive to set.
7.
Be sure the booster is seated firmly.
To remove the booster, rotate it across the Velcro. Do not pull the booster or cables.
Step 4. Connect to AC Power
1.
Connect the AC power cord to the booster (see page 4).
2.
Connect the plug on the other end to a 110V AC power outlet. Be sure all
connections to the booster are tight and secure.
 The booster turns on automatically.
 The Power LED goes ON to show that the booster is ready for use (see
page 4).
 The Alert LEDs flash up to 15 seconds on each band to show the band is
activated (see page 4).
The booster is rated for 5-20V input voltage. DO NOT use the booster with a
higher voltage power supply. This can damage the booster and/or cause
personal injury.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 7
INSTALLATION
Step 5. Configure Gain Settings
1.
Facing the front of your booster, find the Cellular-800 dial on the left side and
the PCS-1900 dial on the right side (see page 4).
2.
Set these dials according to the coverage area and the distance between the
indoor and outdoor antennas (see the following table).
If Coverage Area is...
4000 square feet
and Antenna Separation is...
60 feet
Set Both Dials to...
60
(default setting)
2000 square feet
50 feet
55
1000 square feet
45 feet
50
500 square feet
40 feet
45
100 square feet
25 feet
40
Note: As you can see from the table above, acquiring the recommended indoor and
outdoor antenna separation optimizes coverage significantly. Any reduced antenna
separation reduces the booster’s cellular signal capabilities.
Important: A minimum separation distance of 30 vertical feet is necessary
between the outside and inside antennas. If the inside coverage is not sufficient,
you may need as much as 60 feet of separation. See the table above.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 8
TROUBLESHOOTING
Troubleshooting
In the unlikely event you encounter a problem, use the following steps to identify and
resolve the issue.
Problem
Booster has no power.
Resolution
1.
Verify that the switch on the power supply is
turned on and red LED is ON.
2.
Connect the power supply to an alternate power
source.
3.
Be sure the power source is not controlled by a
switch that can remove power from the outlet.
4.
Check the green POWER LED on the booster. If
it is OFF, return the power supply to CellphoneMate. Contact tech support at 1-888-365-6283,
email support@surecall.com, or go to
surecall.com and log on via online support to
receive a Return Merchandise Authorization
(RMA).
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 9
TROUBLESHOOTING
Problem
After installing the
Resolution
1.
Check the strength of the outside signal as close
booster system, you
as you can to the outside antenna. To measure
have no signal or
your existing cell signal:
reception.
Apple iPhone: dial *3001#12345#*and press
Call. In the top-left corner, a number replaces the
bars.
Android devices: download apps to measure
exact signal strength, such as Network Signal
Info in the Google Play store. Search "check real
signal strength" to find other cell signal
measurement apps.
2.
Double-check all booster and antenna cable
connections.
3.
Be sure your booster's dB gain is turned up to full
power on each dial.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 10
TROUBLESHOOTING
Problem
One of the red lights
Resolution
1.
next to the dials on
your booster is
Turn down the dB gain on the dial until the light
goes OFF or turns yellow.
2.
flashing.
Be sure the inside panel antenna is facing away
from the outside antenna.
3.
Use the recommended antenna separation:
•
65dB  60 ft. separation
•
63dB  50-60 ft. separation
•
55dB  40-50 ft. separation
•
50dB  30-40 ft. separation
•
45dB  20-30 ft. separation
•
40dB  10-20 ft. separation
•
35dB  10 ft. separation
Your booster restarted
Each SureCall booster is equipped with Auto
and shut down for 15
Shutdown to prevent cell tower interference. The
minutes, and is now
outside antenna may be close to a cell tower.
shut down
Move the outside antenna to a location that
permanently.
provides sufficient distance from the cell tower to
prevent the booster from automatically enabling
Auto Shutdown. Once away from the original
location, perform the procedure under Step 4.
Connect to AC Power on page 7.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 11
TROUBLESHOOTING
Problem
Resolution
The red LED goes
More antenna separation is needed. If you cannot
ON.
provide more antenna separation and the Alert
LEDs flash after the initial activation period, lower
the dial above the blinking LED by 5dB (for
example, from 50 to 45) and monitor the bars on
your cell phone to see whether reception improves.
The Power LED does
Be sure the AC outlet is working and is not
not turn ON.
controlled by a wall switch that can remove power
from the outlet.
The Alert LEDs flash
Lower the dial above the blinking LED by 5dB (for
after the initial
example, from 60 to 55) and monitor the bars on
activation period.
your cell phone to see whether reception has
improved.
The Alert LEDs
The booster shuts down automatically, and then
continue to flash.
restarts after 60 seconds. Turn down the Cellular800 or PCS-1900 dial that is oscillating to prevent
the booster from shutting down automatically.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 12
FREQUENTLY ASKED QUESTIONS
Frequently Asked Questions
For a list of Frequently Asked Questions and a comprehensive, up-to-date
Troubleshooting Guide, please visit our website at: www.surecall.com or call us
at 1-800-365-6283.
Obtaining Technical Support
You can also consult a Cellphone-Mate technical specialist directly by emailing us at
support@surecall.com.
Record the model and serial number for your products:
Serial #: ______________________________________________________
Purchase Date: ________________________________________________
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 13
WARRANTY
Warranty
Two-Year Product Warranty
Cellphone-Mate warrants its products for two years from the date of purchase against defects in
workmanship and/or materials.
Products returned by customers must be in their original, un-modified condition, shipped in the original or
protective packaging with proof-of-purchase documentation enclosed, and a Return Merchandise
Authorization (RMA) number printed clearly on the outside of the shipping container.
Buyers may obtain an RMA number for warranty returns by calling the Cellphone-Mate Return Department
toll-free at 1-888-365-6283. Any returns received by Cellphone-Mate without an RMA number clearly printed
on the outside of the shipping container will be returned to sender. In order to receive full credit for signal
boosters, all accessories originally included in the signal booster box must be returned with the signal
booster. (The Buyer does not need to include accessories sold in addition to the signal booster, such as
antennas or cables.)
This warranty does not apply to any product determined by Cellphone-Mate to have been subjected to
misuse, abuse, neglect, or mishandling that alters or damages the product’s physical or electronic properties.
Cellphone-Mate warrants to the Buyer that each of its products, when shipped, will be free from defects in
material and workmanship, and will perform in full accordance with applicable specifications. The limit of
liability under this warranty is, at Cellphone-Mate’s option, to repair or replace any product or part thereof
which shall within TWO YEARS of purchase as determined by examination by Cellphone-Mate, prove
defective in material and/or workmanship. Warranty returns must first be authorized in writing by CellphoneMate. Disassembly of any Cellphone-Mate, Inc. product by anyone other than an authorized representative of
Cellphone-Mate voids this warranty in its entirety. Cellphone-Mate reserves the right to make changes in any
of its products without incurring any obligation to make the same changes on previously delivered products.
As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all
products returned to Cellphone-Mate for repair, and Cellphone-Mate will pay the return shipping with the
exception of products returned from outside the United States, in which case the Buyer will pay the shipping
charges.
The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise,
which are found to meet the applicable specifications or which are not defective or not covered by this
warranty.
Products sold by Cellphone-Mate shall not be considered defective or non-conforming to the Buyer’s order if
they satisfactorily fulfill the performance requirements that were published in the product specification
literature, or in accordance with samples provided by Cellphone-Mate. This warranty shall not apply to any
products or parts thereof which have been subject to accident, negligence, alteration, abuse, or misuse.
Cellphone-Mate makes no warranty whatsoever in respect to accessories or parts not supplied by it.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 14
WARRANTY
Limitations of Warranty, Damages and Liability:
EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS,
GUARANTEES, OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHER WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS,
WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.
CELLPHONE-MATE AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE
PAYMENT, IF ANY, RECEIVED BY CELLPHONE-MATE, INC. FOR THE UNIT OF PRODUCT OR
SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE MAY BE, WHICH IS THE SUBJECT OF
CLAIM OR DISPUTE. IN NO EVENT SHALL CELLPHONE-MATE, INC. BE LIABLE FOR INCIDENTAL,
CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVER CAUSED.
All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California,
and any controversy that cannot be settled directly shall be settled by arbitration in California in accordance
with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered
may be entered in any court having jurisdiction thereof.
If one or more provisions provided herein are held to be invalid or unenforceable under applicable law, then
such provision shall be ineffective and excluded to the extent of such invalidity or unenforceability without
affecting in any way the remaining provisions hereof.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 15
SPECIFICATIONS
Specifications
Specification
FLEX PRO
Supported Standards:
CDMA, GSM, LTE
Uplink Frequency Range:
Cellular-800:
PCS:
Cellular:
PCS:
50 
824 - 849 MHz
1850 - 1910 MHz
869-894 MHz
1930-1990 MHz
Cellular:
PCS:
7dB
65 dB
72 dB
Downlink Frequency Range:
Input/Output Impedance:
Maximum Gain:
Noise Figure:
Maximum Output Power:
2.0
Input: AC 110 V, 60 Hz
Output: DC 5 V/15 V
1 Watt EIRP
Cable:
CM240 or CM400 recommended
RF Connectors:
Power Consumption:
Dimensions:
FCC ID (USA):
N Female, both ends
10W
8 x 5 x 1.25 in.
(20.32 x 12.7 x 3.175 cm.)
1.5 lbs
(.68 kgs.)
RSNFLEXPRO
IC (Canada):
7784A-FLEXPRO
VSWR:
AC Power Transmitter:
Weight:
RS131 – for Canadian Use
Band
Cellular Uplink
PCS Uplink
Cellular Downlink
PCS Downlink
Operating Channel
Frequency Range
824 - 849 MHz
1850 - 1910 MHz
869 - 894 MHz
1930 - 1990 MHz
Pass Bandwidth
Power Rated
38.5 MHz
60.9 MHz
33.0 MHz
73.7 MHz
24.2 dBm
24.1 dBm
1.7 dBm
2.4 dBm
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 16
SAFETY INFORMATION
Safety Information
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
NOTICE: The manufacturer's rated output power of this equipment is for single-carrier operation. For
situations when multiple carrier signals are present, the rating must be reduced by 3.5 dB, especially where
the output signal is reradiated and can cause interference to adjacent-band users.
This power reduction is to be by means of input power or gain reduction and not by an attenuator at the
device output.
La puissance de sortie nominale indiquée par le fabricant pour cet appareil concerne son fonctionnement
avec porteuse unique. Pour des appareils avec porteuses multiples, on doit réduire la valeur nominale de 3,5
dB, surtout si le signal de sortie est retransmis et qu'il peut causer du brouillage aux utilisateurs de bandes
adjacentes. Une telle réduction doit porter sur la puissance d'entrée ou sur le gain, et ne doit pas se faire au
moyen d'un atténuateur raccordé à la sortie du dispositif.
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 17
48346 Milmont Drive
Fremont, California 94538
USA
888.365.6283
Fax: 510.996.7250
www.surecall.com
Cellphone-Mate has made a good faith effort to ensure the accuracy of the
information in this document and disclaims the implied warranties of merchantability
and fitness for a particular purpose and makes no express warranties, except as
may be stated in its written agreement with and for its customers.
Cellphone-Mate shall not be held liable to anyone for any indirect, special or
consequential damages due to omissions or errors. The information and
specifications in this document are subject to change without notice.
Copyright © 2014. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective
owners.
SureCall Flex Pro User Guide
February 6, 2014
SureCall Flex Pro Home and Office Kit Cellphone-Mate, Inc.
All rights reserved.
Page 18

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 18
Language                        : en-US
Tagged PDF                      : Yes
Title                           : SureCall Flex Pro User Guide
Author                          : SureCall
Keywords                        : SureCall, Flex, Pro, User, Guide
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:02:06 16:13:31-08:00
Modify Date                     : 2014:02:06 16:13:31-08:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools