Cellphone Mate SureCall FORCE-550 Consumer Booster User Manual

Cellphone-Mate Inc. dba SureCall Consumer Booster Users Manual

Users Manual

Force5-502G-3G-4G 5-Band WirelessAdjustable Cellular Booster KitUser GuideIntroductionInstallationPackages ContentsConguring Gain SettingIntroductionTroubleshootingTheory of OperationQuick Install GuideBooster HardwareInstallation StepsTheory of OperationSafety Information
2INTRODUCTIONThank you for your purchase of the Force5-50. The Force5-50 5-Band adjustable cellular signal booster removes the frustration over dropped calls, limited range and slow data rates by amplifying incoming and outgoing cellu-lar signals in large watercraft. The Force5-50 enhances 2G, 3G and 4G data reception data for all major US. Carriers.This guide contains all the information you’ll need to get your Force5-50 booster system up and running. If you need any assistance while installing this product please contact tech support at 1-888-365-6283 or email us at: support@surecall.com.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of this device on their network. If you are unsure, contact your provider.How it worksThe Force5-50 is a high-quality bidirectional signal booster that enhances signals to areas that are prone to weak cellular coverage.Force5-50 works with two or more antennas:• up to four inside antennas that communicate with your cellphone. • an outside antenna that communicates with cellular towers.Signals sent from a cellular tower are received by the outside antenna, ampli-ed by the booster and then broadcast to your phone via the inside antenna. When your phone transmits, the signal is sent to the inside antenna, amplied and then sent to the cell tower via the outside antenna.The signal booster requires a minimum cellular signal of low -100 dBm to high -90 dBm. Signal readings usually appear as a negative number. The stronger the signal, the closer it gets to zero. Signals stronger than -50dB may cause the booster to temporarily shut down.To measure your existing cellular signal on an Apple iPhone, dial *3001#12345# and press Call. In the top-left corner, your dB number appears instead of bars.For Android devices, you can download several apps to measure exact signal strength. In your phone’s App Store, search for “check signal strength” to nd a cell signal measurement app.
3INTRODUCTIONPackage Contents:Unpack all package contents, compare them against the package contents list, and check for damage. For missing or damaged items, contact your retailer. Keep the carton and packing material to store the product or if you need to return it.The following image shows the key hardware components on the cellular booster. Refer to this image as you install your Force5-50 components.Booster Outside Antennawith mountInside Antenna with bracketCable-20’ and 40’Phantom Package Contents50 dB adjustable booster(2) SC174 10 foot cablesSC-110W inside antennaSC-200 outside antenna248W-M inside panel antenna18V DC power supplyScrews not supplied* Please purchase separately.Power LEDN connector to outside antennaN connector to inside antennaAlert LEDPower Switch ProgrammerPower Jack Mount Kit
4Quick Install GuideInstallationThe Force5-50 booster kit is specially designed for marine applications. It can also be used for other applications with the right antennas, cables and mounting hardware.Step 1. Connect the SC-200 Outside AntennaThe SC-200 is a, full-band antenna, ideal for marine use. Option 1 (Recommended)1. Choose a mounting location that is as high as possible, free from obstructions and as far as possible from other antennas and sources of RF signal.2. Before mounting base, drill a hole in the middle of the mounting location wide enough in diameter to allow SC-174 cable with FME connector to go through.3. Hand-tighten the antenna base to the ferrule.4. Feed cable, N connector end rst, through bottom of base and through hollowferrule.5. Hand-tighten N connector to outside antenna and antenna to ferrule.6. Feed cable, FME end rst through the drilled hole.7. Mount base (screws not provided) and hand tighten ferrule to mount base.INSTALLATION
5Option 21. When location of outside antenna has been determined, remove cap from ferrule side hole.2. Feed FME connector (small end) and cable through side hole on the f shown in the gure below.3. Feed remainder of cable through ferrule hole until approximately 1” of cable remains.4. Connect N connector to antenna.5. Screw antenna onto ferrule, bend cable to prevent cable from twisting.6. Screw base onto other end of ferrule.7. Mount base onto location.INSTALLATION12121 2 N connectorFME connector12N connector3
6Step 2. Using the SC-174 cableUse the SC-174 cable FME connector to connect the outside antenna to the boost connector marked OUTSIDE (see page 3).Make sure to not coil additional coax cable that might be left over from installa-tion. Hand tighten the connection.Before installing Indoor Antenna check the table below for optimum coverage.Step 3. Connect the Interior AntennaOption 1: Standard Wireless Usage (Recommended)The supplied SC-110W full-band antenna is a compact directional antenna de-signed to cover 2G, 3G, 4G and WLAN systems for Cellular, PCS, AWS and LTE frequencies. It’s a high-gain indoor antenna suited for places where the signal needs to be broadcast over a wide area. This interior antenna transmits and receives signals to cell phones.1. Choose location for mounting antenna on vertical surface. Ideal height from the cabin oor (should be approximate height of cell phone users).Note: As you can see from the table above, acquiring the recommended inside and outside antenna separation optimizes coverage signicantly. Panel antenna can be vertically installed 6 ft. under outside antenna with the booster at full dB gain. Inside panel antenna should face away from outside antenna. If panel antenna faces outside antenna, the booster will oscillate and go into Auto Shutdown.Required Between Outside and Inside Antennaantenna separation• 50dB 8-10 ft. separation• 47dB 5-7 ft. separation• 44dB 3-4 ft. separation• 40dB 1-2 ft. separationAdjust dB Gain according to table below if you cannot achieve maximum separation.
72. Using supplied plate, mark position of desired placement with a pencil or marker.3. Screw (not supplied) mounting plate into place with the slide panel protruding towards you. Provided plastic anchors are only to be used for sheetrock installation.4. Slide antenna securely onto mounting plate.5. Use the additional SC-174 cable to connect the antenna to the booster connector labeled (INSIDE).Note: Be sure to provide enough separation from outside antenna (see table onpage 6. Panel antenna should not face the outside antenna.Option 2 : Low Prole Usage1. The supplied SC-110W patch antenna is intended for indoor use only. Do not mount on a surface within 4” of metal.2. Screw the patch antenna cable to the booster connector labeled (INSIDE).Note: Laboratory tests show that patch antennas can work from as close as 2 feet from outside antennas if the patch antenna is facing away from the outside antenna. If the booster shows oscillation (red light blinking), turn it down in 3 dB increments on the dial of oscillating band until the light stops blinking.
8Step 4. Install the Signal Booster1. Select a location close to a working AC outlet. Do not expose the signal booster to excessive heat, direct sunlight, moisture, and airtight enclosures.2. If you’d like to mount the booster to a wall, mark location of screw tabs on the wall in the desired location3. Use supplied screws or appropriate screws for surface of mounting location and drill through screw tab holes on booster.4. Ensure that the outside antenna cable is connected to the signal booster connector marked OUTSIDE. Hand-tighten the connection.5. Ensure that the inside antenna cable is connected to the signal booster connector marked INSIDE. Hand-tighten the connection.6. Connect the AC power cord to the signal booster.7. Connect the plug on the other end of the 110V AC power outlet.8. Turn the booster’s power switch on. • The signal booster turns on automatically • The Power LED lights up green to show that the signal booster is ready to use. • The Alert LEDs ash red and yellow intermittently on each band, indicating that the band is activated.DIP Switches and LightsThe Force5-50 booster has the following indicators and controls: • PCS Uplink Warning light DIP switches. These DIP switches control the PCS communications with the cellular tower. • PCS Downlink Warning light DIP switches. These DIP switches control the PCS amplication within the building. • Power Light: This light should be illuminated or blinking green at all times while the booster’s power is on. • Cellular Uplink Warning light DIP switches. These DIP switches control the cellular communications with the cellular tower. • Cellular Downlink Warning light DIP switches. These DIP switches control the cellular amplication within the building.Note: If the Power LED does not turn ON or the Alert LEDs continue to ash, see Troubleshooting on page 12-13. This booster is rated for 19V AV input voltage. DO NOT use the booster with a higher voltage power supply. This can damage the booster and/or cause personal injury and void your warranty.
9Step 5. Congure Gain SettingsFacing the front of your booster, nd 9 banks of Dual In-line Package (DIP) switches. These switches allow manual dB gain attenuation for uplink and downlink channels. • Bank 1 controls AT&T communications with the cellular tower. • Bank 2 controls Verizon and AT&T amplication in the building. • Bank 3 controls Verizon communications with the cellular tower • Bank 4 controls Cellular communications with the cellular tower. • Bank 5 controls Cellular amplication in the building. • Bank 6 controls PCS amplication with the cellular tower. • Bank 7 controls PCS amplication in the building. • Bank 8 controls T-Mobile communications with the cellular tower. • Bank 9 controls T-Mobile amplication in the building.The DIP switches in each bank correspond to the following dB gain values:For maximum gain on all channels, your booster ships with all DIP switches turned ON. This setting should always be your starting point when installing or reinstalling the booster. To change it, move the DIP switches to the ON or OFF position. • Moving a switch down (away from the LEDs) turns OFF the switch and increases booster gain for the selected channel. • Moving a switch up (toward the LEDs) turns ON the switch and decreas-es booster gain for the selected channel.Switch settings are cumulative. This means the total amount of attenuation for a channel equals the combined dB of all DIP switches in the same bank being set to ON.WARNING: Do not adjust the uplink and downlink dB attenuation more than 20 dB. This could cause the booster to shut down.12345ON DIP1 2 4 8 16LTE707-ULLTE-707 LTE-78112345ON DIP1 2 4 8 16LTE-DL12345ON DIP1 2 4 8 16LTE781-UL12345ON DIP1 2 4 8 16CELLULAR-ULCellular-80012345ON DIP1 2 4 8 16CELLULAR-DL12345ON DIP1 2 4 8 16PCS-ULPCS-190012345ON DIP1 2 4 8 16PCS-DL12345ON DIP1 2 4 8 16AWS-UL AWS-DLAWS-210012345ON DIP1 2 4 8 16Bank 1 Bank 2 Bank 3 Bank 4 Bank 5 Bank 6 Bank 7 Bank 8 Bank 9Switch11 dBSwitch22 dBSwitch34 dBSwitch48 dBSwitch516 dB
1015 DB21 DB31 DBONONONONONONONOFFONONOFFONOFFONONTo Achieve... Set the DIP Switchs in the Same Bank as Follows...SW1(1 dB)0 DB1 DBOFFONOFFOFFOFFOFFOFFOFFOFFOFFSW2(2 dB)SW3(4 dB)SW4(8 dB)SW5(16 dB)3 DB ON OFFON OFF OFF7 DB ON ONON OFF OFFNote: As you see from the table above, attaining the recommended indoor and outdoor antenna separation optimizes coverage signicantly. Any reduced antenna separation deceases the booster’s cellular signal capabilities.LEDsA Light-Emitting Diode (LED) appears above each DIP switch bank on the top panel of the signal booster.LED123LTE 707 UplinkLTE 781 UplinkCellular 800UplinkOFF = normal operation.ON = LTE AT&T uplink warning. Power o booster immediately.OFF = normal operation.ON = LTE Verizon uplink warning. Power o booster immediately.OFF = normal operation.ON = Cellular uplink warning.Power o booster immediately.Designation Description4 PCS 1900UplinkOFF = normal operation.ON = PCS downlink warning.Power o booster immediately.
11Automatic ShutdownSureCall boosters that have automatic shutdown work in the following way:1. The cellular side (LEDs 4 and 5) is usually the rst side to experience oscillation. When oscillation is detected in the uplink and/or downlink, the appropriate red Warning LEDs ash and Power (LED 3) turns red.2. If oscillation occurs on the PCS side, LEDs 1 and/or 2 blink as appropriate and Power (LED 3) turns red due to cellular oscillation.3. If the problem is not resolved, the affected side shuts down after 30 sec-onds. In general, the cellular side oscillates more easily than the PCS side.4. The booster wakes up and Power (LED 3) turns green. If oscillation re-sumes, the LEDs ash as described previously. These 30-second cycles continue for 15 minutes or until the problem is resolved.5. If the problem is not resolved within 15 minutes, the booster shuts down automatically (all LEDs OFF except Power, which is red) and must be reset by unplugging the booster from the power supply and plugging it back in.6. To resolve oscillation, increase antenna separation and/or the attenuation.If you Want to Improve Coverage • Find a location that receives a stronger signal and relocate the outside antenna to that location. • Increase the distance between the outside and inside antennas.Be sure your signal booster’s dB gain is turned up to maximum gain on each dial (see page 16).LED56AWS 2100UplinkPowerOFF = normal operation.ON = AWS uplink warning. Power o booster immediately.Green ON or blink = booster receiving power.OFF = booster not receiving powerRed ON = oscillation has occurred for longer than 15 minutes and the booster is shutting downDesignation Description
12One of the red LEDs next to the dials on your signal booster is ashing red.Your signal booster restarted and shut down for 15 minutes, and is now shut down permanently.The red LED goes ON.The Power LED does not turn ONTurn down the dB gain on the dial until the light goes OFF or turns yellow.Be sure the inside panel antenna is facing away from the outside antenna.Use the recommended antenna separation:72dB: 100-110 ft. separation65dB: 75-80 ft. separation 55dB: 60 ft. separation 50dB: 50 ft. separation 45dB: 15-20 ft. separation 40dB: 5-6 ft. separation Signal booster has no powerAfter installing your signal boost-er system, you have no signal or reception.Verify that the booster switch is turned on.Connect the power supply to an alternate power source. Be sure the AC outlet is working and is not controlled by a wall switch that can cut power to the outlet. If the green POWER LED on the signal booster is OFF, return the power supply to SureCall. Contact tech support at 1-888- 365-6283 or support@surecall.com, or go to www.surecall.com and log on to online support to receive a Return Merchandise Authorization (RMA).Check the strength of the outside signal as close as you can to the outside antenna. (see instructions on page 7)Double-check all signal booster and antenna cable connections.Be sure your signal booster’s dB gain is turned up to full power on each dial. (see apge 14)Each SureCall signal booster is equipped with Auto Shutdown to prevent cell tower interference. The outside antenna may be close to a cell tower. Move the outside antenna to a location that provides sucient distance from the cell tower to prevent the signal booster from automatically enabling Auto Shutdown. Once away from the original location, perform the procedure under step 3 on page 10More antenna separation is needed. If you cannot provide more antenna separation and the Alert LEDs ash after the initial activation period, lower the dial above the blinking LED by 5dB (for example, from 50 to 45) and monitor the bars on your cell phone to see whether reception improves.Be sure the AC outlet is working and is not controlled by a wall switch that can cut power to the outlet.Problem ResolutionLED ashing yellow This means that the Automatic Gain Control (AGC) is adjusting which is part of the boosters normal operation
13Product Name Force5-50 Uplink Frequency Range (MHz): 698-716 / 776 – 787 / 824-849 1850-1915 / 1710-1755 G Block Included 728-746 / 746 – 757 / 869-894 1930-1995 / 2110-2155 G Block Included50 Ω50dB8 dB≤2.0CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO, LTE and all cellular standardsInput AC110V, 60 Hz; Output DC 19 V1 Watt EIRPSC-400N Female (both ends )<50W11.3” x 10.9” x 2.5”16.5 lbsRSNFORCE-550Downlink Frequency Range (MHz):Supported Standards:AC Input:VSWR:Maximum Gain:Noise Figure:Input Impedance:Maximum Output Power:Cable:RF Connectors:Power Consumption:Dimensions:Operation Temperature: -4ºF to +158ºFWeight:FCC (USA):Your signal booster has no power.Verify that the switch on the power supply is turned on and red LED is ON.Connect the power supply to an alternate power source.Be sure the power source is not controlled by a switch that can remove power from the outlet.Check the green POWER LED on the signal booster. If it is OFF, return the power supply to SureCall. Contact tech support at 1-888-365-6283 or support@surecall.com, or go to www.surecall.com and log on to online support to receive an RMA.The Alert LEDs ash after the initial activation period.The Alert LEDs continue to ashLower the dial above the blinking LED by 5dB (for example, from 65 to 60) and monitor the bars on your cell phone to see whether reception has improved.The singal booster shuts down automatically, and then restarts after 60 seconds. Turn down the Cellular, PCS or LTE/AWS dial that is oscillating dial that is to prevent the signal booster from shutting down autimatically.Problem Resolution
14*All equivalent antennas and cables are suitable for use with the Force5-50 booster.Warning: Unauthorized antennas, cables, and/or coupling devices are prohibited by current FCC regulations. Please contact FCC for details: 1Changes or modications not expressly approved by SureCall could void the user’s authority to operate the equipment.Vehicle KittingMarine KittingDesktop/RV KittingComponentComponentComponentOutdoor Antenna*Outdoor Antenna*Outdoor AntennaSC-200SC-288W or Galaxy 5412-pSC-288WSC-174SC-240-40FN 40 FeetSC-240-40FNLTE-ALTE-ALTE-A3dBi3dBi3dBi3dBi3dBi3dBi3dBi3dBi3dBi5dBi4dBi4dBi3.8dB3.52dB3.52dB3.8dB3.52dB3.52dB4.3dB3.98dB3.98dB8.8dB6.52dB6.52dB3.8dB2.06dB3.8dB2.06dB4.3dB2.06dB8.8dB3.56dB1.1dBi7dBi1.2dBi1.1dBi7dBi1.2dBi1.1dBi7dBi1.2dBi3dBi10dBi3dBiLTE-VLTE-VLTE-V800 MHz800 MHz800 MHz1900 MHz1900 MHz1900 MHz1700 MHz/2100 MHz1700 MHz/2100 MHz1700 MHz/2100 MHz5dBi/5dBi4dBi/4dBi4dBi/4dBi6.98dB/8.96dB6.12dB/6.92dB6.12dB/6.92dB6.98dBi/8.96dB3.36dBi/3.76dB3dBi/3dBi10dBi/10dBi3dBi/3dBiSC-110W (table top)SC-248WSC-120WSC-174SC-240-20FN 20 FeetProduct Number/ DescriptionProduct Number/ DescriptionProduct Number/ DescriptionOutdoor CableOutdoor CableOutdoor CableIndoor CableInside CableIndoor AntennaIndoor AntennaInside AntennaGain/LossGain/LossGain/Loss
15Three-Year Product WarrantySureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials. Specications are subject to change. The three-year warranty only applies to products meeting the latest FCC Certication Guidelines stated on 2/20/2013 and going into eect April 30, 2014. A two-year warranty applies to any products manufactured before May 1, 2014.Products returned by customers must be in their original, un-modied condition, shipped in the original or protective packaging with proof-of-purchase documentation enclosed, and a Return Merchandise Authorization (RMA) number printed clearly on the outside of the shipping container. Buyers may obtain an RMA number for warranty returns by calling the SureCall Return Department toll-free at 1-888-365-6283. Any returns received by SureCall without an RMA number clearly printed on the outside of the shipping container will be returned to sender. In order to receive full credit for signal boosters, all accesso-ries originally included in the signal booster box must be returned with the signal booster. (The Buyer does not need to include accessories sold in addition to the signal booster, such as antennas or cables.) This warranty does not apply to any product determined by SureCall to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages the product’s physical or electronic properties.SureCall warrants to the Buyer that each of its products, when shipped, will be free from defects in material and workmanship, and will perform in full accordance with applicable specications. The limit of liability under this warranty is, at SureCall’s option, to repair or replace any product or part thereof which was purchased up to THREE YEARS after May 1, 2014 or TWO YEARS for products purchased before May 1, 2014, as deter-mined by examination by SureCall, prove defective in material and/or workmanship. Warranty returns must rst be authorized in writing by SureCall. Disassembly of any SureCall product by anyone other than an authorized representative of SureCall voids this warranty in its entirety. SureCall reserves the right to make changes in any of its products without incurring any obligation to make the same changes on previously delivered products. As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all products returned to SureCall for repair, and SureCall will pay the return shipping with the exception of products returned from outside the United States, in which case the Buyer will pay the shipping charges. The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise, which are found to meet the applicable specications or which are not defective or not covered by this warranty. Products sold by SureCall shall not be considered defective or non-conforming to the Buyer’s order if they sat-isfactorily fulll the performance requirements that were published in the product specication literature, or in ac-cordance with samples provided by SureCall. This warranty shall not apply to any products or parts thereof which have been subject to accident, negligence, alteration, abuse, or misuse. SureCall makes no warranty whatsoever in respect to accessories or parts not supplied by it.
16Limitations of Warranty, Damages and Liability:EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS, GUAR-ANTEES, OR REPRESENTATIONS AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PUR-POSE, OR OTHER WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS, WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE PAYMENT, IF ANY, RECEIVED BY CELLPHONE-MATE, INC. FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE MAY BE, WHICH IS THE SUBJECT OF CLAIM OR DISPUTE. IN NO EVENT SHALL SURECALL BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAG-ES, HOWSOEVER CAUSED. All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California, and any controversy that cannot be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered may be entered in any court having jurisdiction thereof. If one or more provisions provided herein are held to be invalid or unenforce-able under applicable law, then such provision shall be ineective and excluded to the extent of such invalidity or unenforceability without aecting in any way the remaining provisions hereof.SAFETY INFORMATIONThis is a CONSUMER device.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specied by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.WARNING: E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE.48346 Milmont DriveFremont, California 94538USA888.365.6283Fax: 510.996.7250www.surecall.comSureCall has made a good faith eort to ensure the accuracy of the information in this document and disclaims the implied warranties of merchantability and tness for a particular purpose and makes no express warranties, except as may be stated in its written agreement with and for its customers.SureCall shall not be held liable to anyone for any indirect, special or consequential damages due to omissions or errors. The information and specications in this document are subject to change without notice. © 2014. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners.
17BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.You MUST operate this device with approved antennas and cables as specied by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.This is a CONSUMER device.Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Co n n e c t t h e e q u i p m e n t in t o a n o u t l e t on a c i r c u i t d i f f e r e n t f r o m t h a t to wh i c h t h e r e c e i v e r is c o n n e c t e d . • Consult the dealer or an experienced radio/TV technician for help.Safety InformationThe Federal Communications Commision (FCC) has tested this product and found it to comply with their RF Exposure Requirements, pursuant to FCC Part 22 and 24.To comply with the FCC RF exposure requirement, keep the human user’s body at least 8” (20cm) from the indoor antenna of the booster.Don’t expose this product to extreme low or high temperature (-4ºF or -20ºC and 150ºF or 70ºC).There are no consumer serviceable or modiable parts inside this booster product. Alteration or abuse of the booster other components will void this product’s warranty, and could be dangerous to the user.FCC 27.50(d)(4) Statement: Fixed, mobile and portable (hand-held) stations operating in the 1720-1755 MHz band are limited 1 Watt EIRP. Fixed stations operating in this band are limited to a maximum anten-na height of 10 meters above ground. Mobile and portable stations operating in this band must employ a means for limiting power to the minimum necessary for successful communications.

Navigation menu