Central Aquatics 15693R Remote Controller User Manual LED Accent Light
Central Aquatics (a division of Central Garden and Pet Company) Remote Controller LED Accent Light
User Manual_LED Accent Light
REMOTE LAYOUT & INSTRUCTIONS
Installing/Replacing the Battery
1. Remove the plastic tab located on the bottom of the remote
to activate the battery.
2. To replace the battery - remove the cover from the back of
the remote by pushing the tab (A) in and pulling the cover out
to release the battery pack (B).
3. Install the new (CR2025) battery.
4. Close the cover – the remote is now be ready for use.
FCC Certification
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Color Changing LED Accent Light
Owner’s Manual
INSTALLATION INSTRUCTIONS
The Aqueon® Color Changing LED Accent Light is fully submersible. It can be installed in the aquarium using the included suction
clips and can also be clipped into Aqueon® LED Strip Lights and Modular LED Light fixtures.
Installation Using the Suction Cups
1. Attach the suction cups to each end of the Accent Light. (Fig. 1)
2. Place the Accent Light in the aquarium, using the
suction cups to attach it securely. Adjust the light to the
desired angle by rotating the light tube in the suction
cups.
a. The Accent Light can be placed anywhere in
the aquarium – just be sure that the control
box is not submersed in the water. (Fig. 1).
3. Connect the transformer to the connector on the Accent
Light.
4. Plug the transformer into an acceptable outlet. Be sure
to incorporate a “drip loop” to prevent water droplets
from running down the cord and into the outlet should
any water get onto the cord.
5. Turn the Accent Light on using the remote control.
Installation into an Aqueon® LED Fixture
1. Turn the light fixture off and unplug the transformer from the outlet prior to installing or uninstalling the LED Accent Light.
Flip the fixture over onto a clean/non abrasive surface so the underside is accessible.
2. Install the Accent light (without the suction cups) on the fixture by snapping both plastic ends of the LED lamp into the
lamp clips inside the fixture housing making sure it is completely installed and held securely by the clips. (Fig. 2)
a. To uninstall, unclip the plastic ends of the lamp from the lamp clips inside the fixture and remove.
3. For the Aqueon® Modular LED Light: Be sure to route the light cord under the cover plates so they can slide back into
their original position, covering the ends of the LED lamps.
4. Connect the transformer to the connector on the Accent Light.
5. Plug the transformer into an acceptable outlet. Be sure to incorporate a “drip loop” to prevent water droplets from running
down the cord and into the outlet should any water get onto the cord.
6. Turn the Accent Light on using the remote control.
Color Changing LED
Accent Light Fits >>
Aqueon® Modular
LED Fixture
Aqueon® LED
Strip Light
Size 30 LED Accent Light
15612
21102
Size 36 LED Accent Light
15613
21103
Size 48 LED Accent Light
15614
-
