Chamberlain Group The 1216 Garage Door Opener User Manual instructions

Download:
Mirror Download [FCC.gov]
Document ID	85331
Application ID	yxp8Uhr6wv0ZhahvFNLqEw==
Document Description	instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	30.07kB (375819 bits)
Date Submitted	2000-02-04 00:00:00
Date Available	2000-02-04 00:00:00
Creation Date	2000-02-04 15:47:16
Producing Software	Photoshop PDF Plug-in 1.0
Document Lastmod	2000-02-04 15:48:13
Document Title	instructions
Document Creator	Photoshop PDF Plug-in 1.0

Lift-Musten
s proh ted, except for ctta
transmitter battery HERE ARE No OTHER USER SERVIOEABLE PARTS.
Features
For use with any SECURITY-i-
compatible garage door opener
receiver.
Personalized Password: Up to
10,000 possible combinations. Password
can be easily changed if desired.
Temporary password: Can be added tor Visitors
or service persons. This temporary password can be
limited to a programmable number ol hours or a
programmable number of entries.
Rolling Code: While your password remains constant until
you change it. the code between the Keyless Entry and the
receiver changes with each use, randomly accessing over
100 billion new codes.
Operation: Opener activates when 4-digit password and
Enter button is pressed,
It wrong numbers are accidentally pressed, correction can be
made immediately. The Enter button will transmit only the last
four digits.
The Keypad will blink tor 15 seconds after the password is
transmitted, During that time the Enter button can be used to
stop or reverse the door travel.
Setting the Personal Entry Password
We recommend that you program your personal
password now, before you install the Keyless Entry.
Then you can test the reception at the mounting
location before you proceed further.
1, Choose a 4-digit personal entry password using the
numbers from 0 to 9 (a number can be used more than
once. for example, 4,0, 4,1).
2. Press the four buttons for the
password, then press and
holdthe Enter button. The
indicator light on the door
opener panel will blink.
3. Press and release the “Smart"
(learn) button on the door
opener panel. After the
opener lights blink, release
the Enter button.
Test by pressing the the password, then press Enter. The
door should begin to move.
SECURITY-I-
Garage Door Opener
'Smarl' (learn)
Button
indicator ugnl
You may also program the Keyless Entry from a
multifunction door control, as follows:
1. With the door closed, enter the tour digit password
desired. then press and hold Enter.
2. Press and hold the light button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights blink, release all buttons.
Model 976LM, 976LMC Security-l-
Wireless Keyless Entry
Children operating or playing with a garage door
opener can iniure themselves or others. The
garage door could close and cause serious injury
or death. Do not allow children to operate the wall
push button(s) or remote control(s).
A moving garage door could lniure or kill someone
under It. Activate the opener only when you can see
the door clearly, It is free of obstructions, and is
properly adiusted.
Installation
Choose a convenient
location for installation. ./
It should be at eye
level. reachable by the
shortest person who
will use it, and within
sight of the door.
For a one-piece door,
use the optional
location shown in the
illustration (on the edge
of the door jamb) to avoid injury as the door
swings up and out.
Test the reception of the Keyless
Entry by operating your opener
from the selected location.
Change the location if necessary.
Remove the battery compartment mowingmle
cover to access the bottom
mounting hole:
- insert a small phillips screw driver ”my Q 1
into the small hole at the bottom of may " "
the cover and gently pull outward to Cover
loosen. V
0 Slide the cover down to remove.
Center the keypad at eye level against the selected
location. Mark 4-1/4" up the centerline from the bottom and
drill a 1/8" pilot hole. Install top mounting screw, allowing
1/ “ to protrude above surface. Position keypad on screw
head and adjust for snug fit.
With cover open so bottom mounting hole is visible, use a
punch to mark hole. Remove keypad and drill 1/8" pilot
hole. Replace keypad and complete installation with
bottom screw, using care to avoid cracking plastic housing.
Do not overtighten.
To replace the battery cover. insert the lip at the top and
snap in place.
Typical
Sectional Door
installation
Exterior Front Wall
l-Plece or
Secltoflal Door
Door Jamb Edge
(Optional Location
for l»Piece Door)
Door Jarnb Face
SECTIONAL DOOR oNLv
KEVPAD MUST BE INSTALLED
WiTHlN SIGHT or THE DOOR
Bottom
Side two contains instructions for changing the personal
entry password and setting a temporary password.
Changing the Personal Entry Password
Press the tour buttons lor the present password, then
press and hold the # button.
The opener light will blink twice. Release the it button.
Press the new 4-digit password you have chosen, then
press Enter.
The opener light will blink once when the password has
been learned,
Test by pressing the new password, then press Enter.
The door should move.
Setting a Temporary Password
In addition to the personal entry password which works at
all times, a 4-digit temporary password can be added for
the convenience of visitors or service persons. This
allows authorized persons a way to gain temporary
access. After a programmed number of hours or number
ol accesses, this temporary entry password expires and
will no longer open the door. The temporary password
can be used to close the door even after it has expired.
To set a temporary entry password:
1. Press the four buttons for your personal entry password
(not the last temporary password), then press and hold
the =l= button.
The opener light will blink three times. Release the
button.
2. Press the temporary 4-digit entry password you have
chosen, then press Enter.
The opener light will blink four times.
3. To set the number of hours this temporary password
will work, press the number of hours (up to 255), then
press *.
OR
3. To set the number of times this temporary password
will work. press the number of times (up to 255), then
press #.
The opener light will blink once when the temporary
password has been learned,
Test by pressing the tour buttons for the temporary
password, then press Enter. The door should move. If the
temporary password was set to a certain number of
openings. remember that the test has used up one
opening.
To clear the temporary password, repeat steps 13,
setting the number ot hours or times to 0 in Step 3.
Battery
The 9 volt battery should produce power for at least one
year. Replace when keypad illumination becomes dim.
FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817
IN CANADA, DIAL 1-800-654-4736
©1997 The Chamberlain Group, Inc.
1 t 4A2232
All nghts Reserved
Printed in Mexlcu

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Modify Date                     : 2000:02:04 15:48:13
Creator                         : Photoshop PDF Plug-in 1.0
Producer                        : Photoshop PDF Plug-in 1.0
Create Date                     : 2000:02:04 15:47:16
Page Count                      : 2

EXIF Metadata provided by EXIF.tools