Chamberlain Group The 1334 User Manual 8

Chamberlain Group Inc, The 8

8

Download: Chamberlain Group The 1334 User Manual 8
Mirror Download [FCC.gov]Chamberlain Group The 1334 User Manual 8
Document ID16196
Application ID/0Mprfg3Ftpm3LYaAg+sjg==
Document Description8
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize4.11kB (51396 bits)
Date Submitted1998-12-15 00:00:00
Date Available1998-09-21 00:00:00
Creation Date2001-07-12 07:57:54
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-07-12 07:57:55
Document Title8

6. OPERATING INSTRUCTIONS
"once- Tacompty um- rcc totes. Mush-m of «narration at this
rm andhrlnnsmitteute prohibited, “not tar manq‘mg no code:
seifinq or {09de m minimum-y. wens me no omen
usea senvrceaauz mars.
Your garage door opener receiver and remote
control have been set at the factory to a matching
code. The opener will activate when the LARGE
button on the remote(s) is pressed. The multi~
function remote(s) can also acu‘vate additional
Below are instructions lor programming your opener
to match the other buttons on your multi-lunction
remote and any additional remotes you may
purchase. See available accessories on page 38.
Your “Smart‘ garage door opener will operate with
up to tour "Smart' remote controls (with green
indicator lights), a Keyless Entry System and code
switch remote controls with red indicator lights.
To Add A Remote
Select a push button to operate the receiver,
Figure 1.
1. Press and hold the remote push button.
2. Then press and release the “Smart' button on the
right side panel of the opener, Figure 2. The
opener lights will flash once.
3. Release the remote push button.
Now the opener will operate when the remote
control push button is pressed.
ll you release the remote control push button
before the opener llghts flash, the opener will
not accept the code.
To Change the Selected Push Button
On the Same Remote
If you decide to use a diflerent remote control button
than originally programmed into the opener, you
need to erase all the Ieamed codes and reprogram
each remote used to operate the garage door
opener.
To Erase All Remote Control Codes
0 Press and hold the ‘Smart' button on the opener
panel until the indicator light tums bit (about 6
seconds). All the codes the opener has learned
will be erased.
- To reprogram, repeat Steps 1 — 3 lor each remote
control in use.
Children operating or playing with a garage
door opener can lnjuro themselves or others.
The garage door could close and cause
serious Injury or death. Do not allow chlldren
to operate the door control(s) or remote
control transmitter(s).
A moving garage door could injure or kill
someone under It. Activate the opener only
when you can see the door clearly, It Is tree of
obstructions, and is properly adjusted.
Figure 1
Multi-Funotion Remote Control
Battery
Indicator ngm
Sela: x Remot-
Prsh Simon
Figure 2
Garage Door Opener
(With ‘Smart' Button)
Burton UV“
Code programmlng Instructions are also located
on the opener panel.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:07:12 07:57:54
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:07:12 07:57:55+01:00
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: HBW1334

Navigation menu