Chamberlain Group The 1573 Remote Control Transmitter User Manual Exhibit D Users Manual per 2 1033 b3

Download:
Mirror Download [FCC.gov]
Document ID	170566
Application ID	ZeB/mRccasEFhnp5nYTIPQ==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.48kB (255974 bits)
Date Submitted	2001-09-20 00:00:00
Date Available	2001-09-20 00:00:00
Creation Date	2001-09-07 15:16:57
Producing Software	Acrobat 4.0 Import Plug-in for Windows
Document Lastmod	2001-09-07 15:17:25
Document Title	Exhibit D Users Manual per 2 1033 b3
Document Creator	Acrobat 4.0 Import Plug-in for Windows

7YP/0/4L /A/ Spade 7/4415
Jltl’l'tl-i= 315MHz 3 Channel Remote Control
The Security+ remote control works only with door
openers and light controls having an orange "Smart"
button and a yellow indicator light.
Programming instructions are described and illustrated
below. The additional push buttons can also activate
other garage door openers and/or light controls.
(Instructions for programming light products are included
with those accessories.)
SECURITY-i GARAGE DOOR OPENERS
To Program the Opener to Accept
the Remote Control Code
Select a remote control push button to operate the opener
The large button is recommended for use With a garage door
opener.
1. Press and hold the selected remote control push button. See
Figure 1
2. Press and release the “Smart“ (learn) button on the opener
panel See Figure 2 The indicator light on the panel Will
begin to blink and the opener lights will flash once,
3. Release the remote push button
Now the opener will operate when that remote control button
is pressed Test it by pressing the remote button to see that
the door goes up and down
Adding a remote can also be done from the door control, as
follows:
1. With the door closed, press and hold a remote push button
2 Press and hold the Light button on the door control.
3 Press and hold the door control push bar.
4. After the opener lights llash. release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the “Smart" button on the opener panel until
the indicator light turns off (about 6 seconds) All transmitter
codes are now erased. Then follow the steps above to re-
program each remote control.
To Control the Opener Lights
With Security-t- transmitters. a remote push button can be
programmed to operate the opener lights without opening the
door.
1. With the door closed, press and hold the remote button that
you want to control the light
2 Press and hold the Light button on the door control.
3 Press and hold the Lock button on the door control.
4. Alter the opener lights flash, release all buttons.
Test by pressing the remote push button The opener lights
should turn on or off but the door should not move.
Replacement Parts
SECuRlTY+ remote case (circuit board not included) ,
MASOSE} 3. 3V7032 Lithium battery — lOAZD; Visor clip ’ 29m?”
NOT ’ To corroly wt‘i rcc rules. adi
aw ,, tansmittor are prohibit exmptloi
battciy T—lLRE AR? No or: a cstn scnv.
or lhndlllr‘atlol‘s pl this receiver
we code Set‘ll’ig or rEplacing‘hc
A 1Lf PAms
Childrcn operating or playing with a garage door opener can lrlJUlC
themselves or others The garage door could close and cause serious
injui y or death. he not allow children to operate the wall push buttons or
remote controls.
I\ moving garage door could iryure or kill someone under it. Activate
the opener only when you can see the door clearly, it lS free of
obstructions. and is properly adyiisted
SECURITY!!-
Remote Control
SECURITY-I-
Garage Door Opener
"Smart“ (learn)
Button
ind cator Lig’t‘
Figure 1 Figure 2
Open/CloselStop Operation
Your Security-I- remote control can be programmed to operate
one door using all 3 buttons: the large button will only open
the door, the middle button will only close the door, and the
third button will stop the door's movement. You may set up
this leature as follows
1. With the door closed, press and hold the
large remote push button.
2. Press and hold the Lock button on the
door control
3 Press and hold the door control push bar
When the opener lights llash. release all buttons Test by
pressing the large (Open) button on the remote. The door
should open. Press it again while the door is open and nothing
should happen. Press the middle (Close) button and the door
should close Press the third (Stop) button whlle the door is
moving and it should stop immediately
Keep batteries away liom small ch
docio
The Remote Control Battery
The lithium battery should produce power for up
to 5 years. To replace battery, pry open case
vith visor clip or screwdriver. as shown insert
battery positive side up (+).
Dispose of old battery properly.
FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-800-528-2817
©1993. Chamberlain Group Inc
l 14A2335
All Rights Reserved
Printed in MCXICO

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2001:09:07 15:17:25-05:00
Create Date                     : 2001:09:07 15:16:57-05:00
Creator                         : Acrobat 4.0 Import Plug-in for Windows
Producer                        : Acrobat 4.0 Import Plug-in for Windows
Page Count                      : 1

EXIF Metadata provided by EXIF.tools