Chamberlain Group The 1650 Remote Control Transmitter User Manual Exhibit D Users Manual per 2 1033 b3

Download:
Mirror Download [FCC.gov]
Document ID	529725
Application ID	GLxJpSpuXoOxRDh0erGREA==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	9.42kB (117706 bits)
Date Submitted	2005-04-08 00:00:00
Date Available	2005-04-08 00:00:00
Creation Date	0000-00-00 00:00:00
Document Lastmod	0000-00-00 00:00:00
Document Title	Exhibit D Users Manual per 2 1033 b3

WSTKueTIMJ SAMPLE 0F 377LM
WMaf-te
nnaFEssloNAL
NOTICE: To comply WM FCC rules, adjuslmeot or modifications of this recetver
and/or transmllter are prohibited, except lor changlng the was selling or
replacing the battery THERE ARE NO OTHER usER sERVicEABLE PARTS
3q~/
The MLM remote control can activate four separate
garage door openers, gate openers, entryways and/or light
controls. (instructions for programming light products are
included with those accessories.)
All lour push buttons work with common platform receivers
having a yellow indicator light. The rolling code between
these channels and the receiver changes with each use,
randomly accessing over 100 billion new codes.
Instructions are described and illustrated below.
WHEN USED WITH SECURITY+
GARAGE DOOR OPENERS
NOTE: When using Common Platform receiver, refer to
instructions supplied with receiver.
To program the opener to accept the remote control
code:
Select a remote control push button, The first button is
recommended lor use with a garage door opener.
1, Press and ho/dthe selected push button. See Figure 1.
2.Press and release the “Smart" (learn) button on the
opener panel. See Figure 2. The indicator light on the
panel will begin to blink and the opener lights wili‘flash
once.
3. Release the remote push button.
Now the opener will operate when that push button is
pressed.
Adding a remote can also be done from the door
control, as follows:
1. With the door closed, press and hold the selected push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. Afler the opener lights flash, release all buttons.
Test by pressing the remote push button (garage door
should open).
To erase all remote control codes from the receiver:
Press and hold the “Smart" button on the opener panel unlil
the indicator light turns off (about 6 seconds), All transmitter
codes inside the receiver are now erased. Then follow the
steps above to re-program each remote control.
To check batteries:
1. Look at LED while pressing any button. A flashing LED
indicates batteries are ok. See Figure 3.
2. See page 2 for battery replacement instructions.
394
Model 9821‘LM
4-Channel Remote Control
OWNER'S MANUAL
m t .
Children operating or playing with a garage door
opener can injure themselves or others. The garage
door could close and cause serious Injury or death.
Do not allow children to operate the wall push
buttons or remote controls.
A moving garage door could injure or kill someone
under it. Activate the opener only when you can see
the door clearly, it is free of obstructions, and is
properly adjusted,
Figure 1
39 '+
Model MM
Remote Control
Figure 2
SECU RITY+
Garage Door Opener
"Smart" (learn)\
Button Indicator Light
Figure 3
Indicator
Light
Replacement Parts
ModeI‘SMLM remote case
(circuit board not included) . .
Keep batteries away from small children. If 3v2032 Lithium battery (2 required) O10A20
swallowed, promptly notify doctor. Visor clip
.K74-1 7929
Figure 4
The Remote Control Batteries
1. The lithium batteries should produce power for up to
5 years,
24 To replace, pry open case with visor clip or screwdriver, as
shown. insert batteries positive side up (+)_ See figure 4.
3, Dispose oioid batteries properly.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-523-2817
® 2001. The Chamberlain Group Inc,
All Rights Reserved Printed in Mexico
01~17928A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 2

EXIF Metadata provided by EXIF.tools