Chamberlain Group The 1662 Remote Control Transmitter User Manual

Chamberlain Group Inc, The Remote Control Transmitter 114A2504 Clicker

a href="https://usermanual.wiki/Chamberlain-Group-The" itemprop="url"> Chamberlain Group The >

Exhibit D Users Manual per 2 1033 b3

The Receiver DIP switch has three positions labeled “+”, “0” and “-”. The “0” setting cannot be used with the clicker remote.1) Reset switches: 1 to “-” and positions 2 through 9 to a randomsetting using “+” and the “-”. DO NOT USE THE “O” SETTING. 2) Gather any existing remotes and open to expose the DIP switches. Resetthe DIP switch to match the newly coded receiver. Note: some three button remotes donot have a #1 switch. Match the 2 through 9 to the receiver. On three button remotesthe large button is now programmed to activate the door. 3) Test all the newly codedremote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.After determining that the Receiver has a yellow, white or graylearn button, 1) Gather any existing remotes and open to exposethe DIP switches labeled “+”, “0” and “-”. 2) Reset switches: 1 to “-” and positions 2 through 9 to a random setting using “+” and the “-”. DO NOT USE THE “0” SETTING, SET ALL REMOTESTO THE SAME SETTING. On three button remotes the large button isnow programmed to activate the door. 3) The recoded remotes must beprogrammed to the receiver. Press and release the smart-learn button.Then press and hold the existing remote push button for three seconds. 4) Test all the newly coded remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.With this type receiver, the existing remotes do not contain DIP switches. Proceed to BRAND MODE SETTINGS.LOCKLIGHTMotor Unit & ReceiverWall Mounted ControlRemote ControlThe clicker remote can be programmed to operate up to 2 garage door openers or gates,including different brands. All programming is done using the:• Brand switch • Transmitter DIP switch • Transmit push buttons A and B, and LED indicatorDetermine the BRAND of the existing garage door opener or handheld remote controls. If allremote controls are lost, the BRAND is located on the ceiling mounted motor unit or on thereceiver near the flexible wire antenna. Proceed to the SECTION indicated on the BRAND chartbelow.Note: If programming to more than one opener, after programming button “A” refer to brandchart, and follow the instructions pertaining to the brand you wish to program into button “B”.When the remotes range is diminished, operation is intermittent, or the LED dims, replace thebattery. Memory is not lost when the battery is removed. Note: Dispose of old batteriesproperly.Model No. CLT 1Universal Garage Door Opener Remote ControlCLICKERProceed to appropriate section.Step 4 - When LED flashes,release both buttons.Step 5 - Press the button you wish to operate theopener (your choice).Step 6 - Programming is complete, to test, press the button selected to activate garage door.Step 2Step 1Existing RemoteClicker RemoteMatchexistingcodes.Set extraswitches off.➡➡SECTION III• Open existing remote; determine if there are 9 or 12 code switch settings.• Set brand mode switches on clicker remote. • Program clicker remote push button.Step 1ORANGE/REDSMART-LEARN BUTTONSECTION I SECTION II• Determine specific brand and circle above. • Open existing remote to expose code switches.• Set brand mode switches on clicker remote. • Program clicker remote push button.➡Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt-➡ON ON OFF OFFOFF ON ON OFFOFF OFF OFF OFFSTANLEYON OFF OFF OFFMULTI-CODEOFF ON OFF OFFLINEAR/MOORE-O-MATICOFF OFF ON OFFGENIE 9 SWITCHON OFF ON OFFGENIE 12 SWITCHSECTION I - Chamberlain, Sears, LiftMaster, Master Mechanic, DoItSECTION II - Stanley, Multi-code, Linear, Moore-O-MaticSECTION III - GenieBRAND CHARTLEDButton BButton ABrand SwitchDip SwitchBatterySlide battery door down & RemovePreparationDetermine if your motor unit/receiver system has DIP switches or a smart-learn button.(Locate the small gray wire antenna. Somemodels require removing the light lens.)• If the Receiver has 9 DIP switches Proceed to TYPE A• If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B• If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE CSMART-LEARNBUTTON➡DIP SWITCHESATYPEBTYPECTYPE➡✚–O231KG KG➡Use this button231KG KG➡Remote push buttonTECHNICAL SUPPORT: 800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead DoorCorporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. DoIt is a trademark of DoIt Best Corporation.©2001, Clicker Corporation114A2504B All Rights Reserved Printed in Mexico➡Existing RemoteMatch existing codes. Set extraswitches off.➡➡ClickerRemote✚O–123456789RANDOM 2-9DO NOT USE✚O–123456789RANDOM 2-9DO NOT USEUse this button➡FOR TYPE A AND BON ON ON OFFGREEN SMART-LEARNBUTTON➡Code switchsettings arenot used.➡➡Code switchsettings arenot used.➡- Stanley, Multi-Code, Linear, Moore-O-Matic- Genie - 9 Code Switch, Genie - 12 Code SwitchStep 1 - Step 1 Step 3 - Press and hold bothbuttons for 5 secondsor until LED begins toflash.Step 4 - When LED flashes,release both buttons.Step 5 - Press the button you wish to operate theopener (your choice).Step 6 - Programming is complete, to test, press the button selected to activate garage door.Step 2Existing RemoteClicker RemoteMatchexistingcodes.Set extraswitches off.➡➡Step 3 - Press and hold both buttons for 5seconds or until LEDbegins to flash.BRAND MODE SETTINGS - Set switches on clicker remoteStep 2 - Press and hold both buttons for 5 seconds or until LED begins to flash.Step 3 - When LED flashes, release both buttons.Step 4 - Press the button you wish to operate the opener (your choice).For type A & B, proceed to step 6. For type C, continue on to Step 5.231KG KGA. Press and releaseSmart-Learnbutton.Step 6 - Programming is complete, to test, press the button selected to activate garage door.FOR TYPE C– OR –B. Press and hold button selected in Step 4 for 3 seconds.Continue to Step 2.Step 5 Note: Use pen or small screwdriver to move dip switches.1234567891234➡➡10 1112ONON➡➡UP Position is ONDOWN Position is OFFUP Position is ONDOWN Position is OFFWARNINGCAUTION WARNINGWARNINGTo prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters.• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.• ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross path of moving gate or door.NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter areprohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation.
Download: Chamberlain Group The 1662 Remote Control Transmitter User Manual
Mirror Download [FCC.gov]Chamberlain Group The 1662 Remote Control Transmitter User Manual
Document ID662209
Application IDuAXVHVm/PAartLdCSyY0Pg==
Document DescriptionExhibit D Users Manual per 2 1033 b3
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.6kB (182550 bits)
Date Submitted2006-05-26 00:00:00
Date Available2006-05-26 00:00:00
Creation Date2001-06-25 14:13:25
Producing SoftwareAcrobat Distiller 4.05 for Macintosh
Document Lastmod2006-05-22 14:00:09
Document Title114A2504 Clicker
Document CreatorQuarkXPressª: LaserWriter 8 8.7
Document Author: Chamberlain Group
FCC ID Filing: HBW1662

Navigation menu