Chamberlain Group The NTD Wireless Portable Intercom User Manual

Chamberlain Group Inc, The Wireless Portable Intercom 1

a href="https://usermanual.wiki/Chamberlain-Group-The" itemprop="url"> Chamberlain Group The >

Contents

User Manual 1

Carton InventoryOverviewThe Intercom has up to a 1000' range and allows multiple simultaneous conversations, using a 900 MHz secure digital radio link. The intercoms form an exclusive network and respond only to other intercoms in the network.Mounting Tape1Alcohol WipeIntercom (2)Operation & FeaturesCall Mode: In Call Mode the intercom may only be used to call the intercom network and will not be able to hear conversation from within the network.To put intercom into Call Mode place Dipswitch #1 to the UP position.Volume: To increase the intercom volume, place Dipswitch #4 to the UP position.Sensitivity: The sensitivity setting controls the speaker volume on the other intercom. To increase the speaker volume on the other intercom place Dipswitch #3 to the UP position.NOTE: Dipswitch #2 is not used.Talk Button: To talk, hold down the Talk button and all intercoms in the network will receive the signal. When holding down the Talk button on a different intercom, a secure channel is created and the other intercoms in the network do not hear the conversation.Battery: The AA Alkaline batteries (not provided) will last up to a year depending on use (Lithium batteries recommended for colder environments). When the batteries are low it will emit two beeps every ten minutes.Talk ButtonSpeakerModel NTD2Wireless Portable Indoor/Outdoor Intercom® Learn ButtonDipswitch BlockMounting IntercomStep 1Mount Intercom with small silver screws. See mounting template on page 3. Screw the top two screws halfway into the mounting surface. Place back of intercom over screws. Tighten screws.The Intercom can be mounted by using the included screws or by using the double-sided mounting tape. It is recommended to use the mounting tape on surfaces such as metal or glass.Put the remaining silver screws into the bottom holes of intercom. Tighten screws.Mounting with ScrewsStep 2
2Step 1Peel off white paper from mounting tape. Firmly press mounting tape on back of intercom.Peel paper from mounting tape. Firmly press intercom onto mounting surface.Clean back of intercom and mounting surface using the alcohol wipe.Mounting with TapeStep 2Step 3Assemble IntercomCreate New NetworkThe intercom must be programmed to at least one other intercom to become a network or it can be programmed into an existing network.Press the Learn button on the new intercom until a beep is heard. Within 5 seconds put the second intercom into Learn Mode (refer to table below).Add to an Existing NetworkEach intercom will emit a tone when programmed into network. Repeat for any additional intercoms.NOTE: Do not program new intercoms to each other before adding them to the network or they will form a separate network and the memory will need to be cleared.Install 4 AA Alkaline batteries (not provided). (Lithium batteries recommended for colder environments.)Programming IntercomEach intercom will emit a tone when programmed into network. Repeat for any additional intercoms.INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds.ORPress the Learn button on the new intercom until a beep is heard. Within 5 seconds put any networked intercom into Learn Mode (refer to table below).INTERCOM LEARN MODE Press the Learn button until a beep is heard. Press and hold both buttons for 5 seconds.OR
Download:
Mirror Download [FCC.gov]
Document ID1190526
Application IDUvxyYILLMydzzW8XzQFJvA==
Document DescriptionUser Manual 1
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize14.31kB (178843 bits)
Date Submitted2009-10-28 00:00:00
Date Available2009-10-28 00:00:00
Creation Date2009-09-23 07:49:51
Document Lastmod2009-10-19 14:33:59
Document TitleUser Manual 1
FCC ID Filing: HBWNTD

Navigation menu