Chamberlain 940Ev Wireless Keyless Entry Users Manual S AND 940EVC
2015-03-09
: Chamberlain Chamberlain-940Ev-Wireless-Keyless-Entry-Users-Manual-590568 chamberlain-940ev-wireless-keyless-entry-users-manual-590568 chamberlain pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
WIRELESS KEYLESS ENTRY • MODELS 940EV AND 940EVC For use with Chamberlain 315 MHz or 390 MHz garage door openers manufactured after January 1, 1993. The garage door opener activates when the 4-digit Personal Identification Number (PIN) and ENTER button are pressed on the Keyless Entry. Install the battery and program the Keyless Entry prior to installation. Make sure the garage door opener has a working light bulb because it is a programming indicator. Enter a 4-digit personal identification number (PIN) of your choice: ? ? ? ? 4 Press and hold the and # buttons until the lights on the keypad stop blinking. * Learn LED Green or Red/Orange Purple 2 1 Locate the Learn button on the garage door opener. NOTE: Your garage door opener may look different. Learn LED Learn LED 3 To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: • Install Keyless Entry Control within sight of the garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door. • ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls. • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. Press and release the Learn button. The LED will light. Within 30 seconds... Yellow 5 Press and release the ENTER button... Check to see if the light bulb blinks. If not, slowly press and release the ENTER button until the light bulb blinks. Be careful NOT to press the ENTER button after the light bulb blinks. Press 0 to complete the programming. 6 To test, press the PIN, then press the ENTER button. ? ? ? ? PIN + The garage door opener will activate. To program the Keyless Entry to more than one garage door opener, repeat the steps above using a new PIN for each additional garage door opener. 1 Press the programmed PIN 2 Press and hold the that you want to change. # button until... 3 Enter the new 4-digit PIN of your choice, then the ENTER button. The garage door opener will activate. then press the ENTER button. ? ? ? ? ? ? ? ? new PIN + ...the light bulb blinks twice. * For garage door openers that have a green Learn button or an external receiver repeat "Program Initial PIN" to change the existing PIN. 4 To test, press the new PIN, The light bulb will blink once. PROGRAM A TEMPORARY PIN NOTE: This feature is not available on garage door openers that have a green Learn button or an external receiver. A temporary 4-digit PIN can be programmed to allow access to visitors. Each programmed PIN can program one temporary PIN. The temporary PIN can be set for a number of hours or a number of door openings. The temporary PIN cannot be the same as any previously programmed PIN. 1 Press any programmed PIN, then press and hold the * button until... ? ? ? ? PIN 2 Enter the temporary 4-digit PIN of your choice, then press the ENTER button. + ? ? ? ? + Temporary PIN The light bulb will blink 4 times. ...the light bulb blinks 3 times. 3 3 Press the number of hours the Then press + the temporary PIN button. will work (up to 255). Press the number of openings the temporary PIN will work (up to 255). * + Then press the # button. 1 blink 1 blink To test, press the temporary PIN, then press the ENTER button. The garage door opener will activate. If the temporary PIN was set for a number of openings, the test will use up one opening. To clear the temporary PIN, repeat steps 1-3 above, setting the number of hours or openings to 0 in step 3. INSTALLATION 1 2 3 4 5 Select a location to mount the Keyless Entry at a minimum height of 5 feet (1.5 m) out of the reach of children. Remove battery cover and battery. Mark the top mounting hole and drill 1/8 inch (3.2 mm) pilot hole. Install the top screw, allowing 1/8 inch (3.2 mm) to protrude above the surface. Position the Keyless Entry over the top screw. Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot hole. Install the bottom screw. Do not overtighten to avoid cracking the plastic housing. 6 Reinstall battery and replace cover. BATTERY OPERATION The garage door opener activates when the PIN and ENTER button are pressed. The keypad will blink for 15 seconds, during that time the ENTER button can be used to stop, start or reverse the door. If the wrong number is accidentally pressed, press the correct PIN then the ENTER button. The Keyless Entry will transmit only the last four digits that were pressed before the ENTER button. ONE BUTTON CLOSE: The Keyless Entry has a feature that allows the door to be closed using the ENTER button instead of a PIN. NOTE: This feature is not available on garage door openers manufactured prior to 2006 or an external receiver. To deactivate the one button close feature: 1 Press and hold the 1 and 9 buttons for 10 seconds. 2 The keypad will blink four times when the one button close feature is deactivated. To activate the one button close feature: 1 Press and hold the 1 and 9 buttons for 10 seconds. 2 The keypad will blink twice when the one button close feature is activated. REPLACEMENT PARTS Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10A25 Keypad Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D621 Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41D541 1-800-528-9131 114A3926B © 2011, The Chamberlain Group, Inc. All Rights Reserved WARNING To prevent possible SERIOUS INJURY or DEATH: • NEVER allow small children near batteries. • If battery is swallowed, immediately notify doctor. Replace the battery when the keypad becomes dim or does not light after a button is pressed. Dispose of old battery properly. 9V Battery NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS. This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARRANTY ONE YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first retail purchaser of this product that is free from defect in materials and/or workmanship for a period of 1 year from the date of purchase. www.chamberlain-diy.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Extract, Print high-res Author : The Chamberlain Group, Inc. Create Date : 2010:11:11 10:56:32-07:00 Keywords : WIRELESS KEYLESS ENTRY, 940EV 940EVC Modify Date : 2013:10:18 09:28:08-07:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:56:37 Metadata Date : 2013:10:18 09:28:08-07:00 Format : application/pdf Creator : The Chamberlain Group, Inc. Title : WIRELESS KEYLESS ENTRY MODELS 940EV AND 940EVC Description : WIRELESS KEYLESS ENTRY MODELS 940EV AND 940EVC Subject : WIRELESS KEYLESS ENTRY, 940EV 940EVC Document ID : uuid:e0b8da1f-b4ab-af41-b1b0-7b689b4ff868 Instance ID : uuid:44b39265-3b7f-e34e-be88-6be6b28301aa Page Layout : SinglePage Page Mode : UseOutlines Page Count : 2EXIF Metadata provided by EXIF.tools