Champion Power Equipment 100100 Owners Manual

: Champion-Power-Equipment Champion-Power-Equipment--100100-Owners-Manual-802512 champion-power-equipment--100100-owners-manual-802512 champion-power-equipment pdf

Open the PDF directly: View PDF .
Page Count: 30

OWNER’S MANUAL & OPERATING INSTRUCTIONS

12039 Smith Ave.

Santa Fe Springs CA 90670

USA / 1-877-338-0999

www.championpowerequipment.com

SAVE THESE INSTRUCTIONS

Important safety instructions

are included in this manual.

MADE IN CHINA

REV 100100-20141230

100100

MODEL NUMBER

4000 Starting Watts / 3250 Rated Watts

PORTABLE GENERATOR

Recoil Start

*We are always working to improve our products. Therefore, the enclosed product may differ slightly from the image on the cover.

Have questions or need assistance?

Do not return this product to the store!

WE ARE HERE TO HELP!

Visit our website:

www.championpowerequipment.com

for more info:

s Product Info & Updates

s Frequently Asked Questions

s Tech Bulletins

s Product Registration

– or –

Call our Customer Care Team Toll-Free at:

1-877-338-0999

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

Your Champion Power Equipment product is designed and rated for continuous operation at ambient temperatures up to

40°C (104°F). When your product is needed your product may be operated at temperatures ranging from -15°C (5°F) to

50°C (122°F) for short periods. If the product is exposed to temperatures outside this range during storage, it should be

brought back within this range before operation. In any event, the product must always be operated outdoors, in a

well-ventilated area and away from doors, windows and other vents.

100100

TABLE OF CONTENTS

Introduction ............................ 1

Introduction .......................... 1

Portable Power Generator . ................ 1

Accessories .......................... 1

This Booklet .......................... 1

Manual Conventions . ...................... 2

Safety Rules . ........................... 3

Controls and Features ..................... 5

Generator . ........................... 5

Power Panel .......................... 6

Parts Included ........................ 7

Wheel Kit . ......................... 7

Other ............................ 7

Assembly .............................. 8

Remove the Generator from the Shipping Carton . 8

Install the Wheel Kit .................... 8

Install the Support Leg .................. 8

Install the Handle ...................... 8

Add Engine Oil ........................ 9

Add Fuel ........................... 10

Grounding .......................... 10

Operation . ............................ 11

Generator Location .................... 11

Grounding .......................... 11

Surge Protection ...................... 11

Starting the Engine .................... 12

Connecting Electrical Loads .............. 12

Stopping the Engine ................... 12

Do Not Overload Generator . .............. 13

Capacity ......................... 13

Power Management . ................. 13

Maintenance and Storage .................. 14

Engine Maintenance ................... 14

Oil ............................. 14

Spark Plugs ....................... 14

Air Filter ......................... 14

Spark Arrester ....................... 15

Cleaning ........................... 15

Adjustments ......................... 15

Maintenance Schedule . ................. 15

Generator Maintenance ................. 16

Storage ............................ 16

Generator Storage ................... 16

Disconnect the Battery ............... 16

Charge the Battery .................. 16

Specifications .......................... 17

Engine Specifications .................. 17

Generator Specifications ................ 17

Fuel .............................. 17

Oil ............................... 17

Spark Plugs ......................... 17

Valve Clearance . ...................... 17

Wiring Diagram ....................... 18

Parts Diagram . ....................... 19

Parts List . .......................... 20

Engine Parts Diagram .................. 21

Engine Parts List ..................... 22

Troubleshooting . ........................ 23

Warranty ............................. 24

Warranty Qualifications ................. 24

Repair/Replacement Warranty . ............ 24

Do Not Return The Unit To

The Place Of Purchase . ................. 24

Warranty Exclusions. . . . . . . . . . . . . . . . . . . . 24

Normal Wear ...................... 24

Installation, Use and Maintenance . ....... 24

Other Exclusions . ................... 24

Limits of Implied Warranty

and Consequential Damage ............ 24

Contact Information . ................... 24

Address . ......................... 24

Customer Service ................... 24

Technical Service ................... 24

PORTABLE GENERATOR

4000 Starting Watts / 3250 Rated Watts

Recoil Start

1

ENGLISH 100100

Introduction

Congratulations on your purchase of a Champion

Power Equipment generator. CPE designs and builds

generators to strict specifications. With proper use and

maintenance, this generator will bring years of satisfying

service.

Portable Power Generator

This unit is a gasoline engine driven, alternating current

(AC) generator. It is designed to supply electrical power

for lighting, appliances, tools and similar equipment.

Record the model and serial numbers as well as date and place of purchase for future reference. Have this

information available when ordering parts and when making technical or warranty inquiries.

Accessories

Champion Power Equipment manufactures and sells

accessories designed to help you get the most from your

purchase. To find out more about our covers and power

cables, please visit our web site at:

www.championpowerequipment.com

This Booklet

Every effort has been made to ensure the accuracy and

completeness of the information in this manual. We reserve

the right to change, alter and/or improve the product and

this document at any time without prior notice.

Champion Power Equipment Support

Model Number

Serial Number

Date of Purchase

Purchase Location

1-877-338-0999

100100

For Oil Type see “Add Engine Oil” section. For Fuel Type see “Add Fuel” section.

INTRODUCTION

2

100100 ENGLISH

This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol

is used with a key word to alert you to potential hazards in operating and owning power equipment.

Follow all safety messages to avoid or reduce the risk of serious injury or death.

MANUAL CONVENTIONS

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

CAUTION

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

DANGER

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

WARNING

If you have questions regarding your generator, we can

help. Please call our help line at 1-877- 338- 0999

NOTE

3

ENGLISH 100100

SAFETY RULES

Generator exhaust contains carbon monoxide, a

colourless, odourless, poison gas. Breathing carbon

monoxide will cause nausea, dizziness, fainting or

death. If you start to feel dizzy or weak, get to fresh

air immediately.

Operate generator outdoors only in a well ventilated

area.

DO NOT operate the generator inside any building,

including garages, basements, crawlspaces and

sheds, enclosure or compartment, including the

generator compartment of a recreational vehicle.

DO NOT allow exhaust fumes to enter a confined

area through windows, doors, vents or other

openings.

DANGER CARBON MONOXIDE: using a generator

indoors CAN KILL YOU IN MINUTES.

DANGER

Rotating parts can entangle hands, feet, hair,

clothing and/or accessories.

Traumatic amputation or severe laceration can result.

Keep hands and feet away from rotating parts.

Tie up long hair and remove jewelry.

Operate equipment with guards in place.

DO NOT wear loose-fitting clothing, dangling

drawstrings or items that could become caught.

DANGER

Generator produces powerful voltage.

DO NOT touch bare wires or receptacles.

DO NOT use electrical cords that are worn, damaged

or frayed.

DO NOT operate generator in wet weather.

DO NOT allow children or unqualified persons to

operate or service the generator

Use a ground fault circuit interrupter (GFCI) in damp

areas and areas containing conductive material such

as metal decking.

Use approved transfer equipment to isolate generator

from your electric utility and Notify your utility

company before connecting your generator to your

power system.

DANGER

Sparks can result in fire or electrical shock.

When servicing the generator:

Disconnect the spark plug wire and place it where it

cannot contact the plug.

DO NOT check for spark with the plug removed.

Use only approved spark plug testers.

WARNING

Running engines produce heat. Severe burns can

occur on contact.

Combustible material can catch fire on contact.

DO NOT touch hot surfaces.

Avoid contact with hot exhaust gases.

Allow equipment to cool before touching.

Maintain at least 91.4 cm (3 ft.) of clearance on all

sides to ensure adequate cooling.

Maintain at least 1.5 m (5 ft.) of clearance from

combustible materials.

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical devices

or medical appliances.

Inform your electricity provider immediately if you

or anyone in your household depends on electrical

equipment to live.

Inform your electrical provider immediately if a

loss of power would cause you or anyone in your

household to experience a medical emergency.

WARNING

The engine exhaust from this product contains

chemicals known to the state of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

Read this manual thoroughly before operating your

generator. Failure to follow instructions could result

in serious injury or death.

WARNING

4

100100 ENGLISH

SAFETY RULES

Improper treatment or use of the generator can

damage it, shorten its life and void your warranty.

Use the generator only for intended uses.

Operate only on level surfaces.

DO NOT expose generator to excessive moisture,

dust, or dirt.

DO NOT allow any material to block the cooling slots.

If connected devices overheat, turn them off and

disconnect them from the generator.

DO NOT use the generator if:

– Electrical output is lost

– Equipment sparks, smokes or emits flames

– Equipment vibrates excessively

CAUTION

Operation of this equipment may create sparks that

can start fires around dry vegetation.

A spark arrestor may be required. The operator

should contact local fire agencies for laws or

regulations relating to fire prevention requirements.

WARNING

Rapid retraction of the starter cord will pull hand and

arm towards the engine faster than you can let go.

Unintentional startup can result in entanglement,

traumatic amputation or laceration.

Broken bones, fractures, bruises or sprains could result.

When starting engine, pull the starter cord slowly

until resistance is felt and then pull rapidly to avoid

kickback.

DO NOT start or stop the engine with electrical

devices plugged in.

WARNING

Exceeding the generator’s running capacity can

damage the generator and/or electrical devices

connected to it.

DO NOT overload the generator.

Start the generator and allow the engine to stabilize

before connecting electrical loads.

Connect electrical equipment in the off position,

and then turn them on for operation.

Turn electrical equipment off before stopping the

generator.

DO NOT tamper with the governed speed.

DO NOT modify the generator in any way.

CAUTION

Fuel and fuel vapours are highly flammable and

extremely explosive.

Fire or explosion can cause severe burns or death.

Unintentional startup can result in entanglement,

traumatic amputation or laceration.

When adding or removing fuel:

Turn the generator off and let it cool for at least two

minutes before removing the fuel cap. Loosen the

cap slowly to relieve pressure in the tank.

Only fill or drain fuel outdoors in a well-ventilated area.

DO NOT pump gas directly into the generator at the

gas station. Use an approved container to transfer

the fuel to the generator.

DO NOT overfill the fuel tank.

Always keep fuel away from sparks, open flames,

pilot lights, heat and other sources of ignition.

DO NOT light or smoke cigarettes.

When starting the generator:

DO NOT attempt to start a damaged generator.

Make certain that the gas cap, air filter, spark plug,

fuel lines and exhaust system are properly in place.

Allow spilled fuel to evaporate fully before

attempting to start the engine.

Make certain that the generator is resting firmly on

level ground.

When operating the generator:

DO NOT move or tip the generator during operation.

DO NOT tip the generator or allow fuel or oil to spill.

When transporting or servicing the generator:

Make certain that the fuel shutoff valve is in the off

position and the fuel tank is empty.

Disconnect the spark plug wire.

When storing the generator:

Store away from sparks, open flames, pilot lights,

heat and other sources of ignition.

DANGER

5

ENGLISH 100100

Read this owner’s manual before operating your generator. Familiarize yourself with the location and function of the

controls and features. Save this manual for future reference.

(1) Fuel Tank – 13 L (3.4 gallon) capacity fuel tank.

(2) Choke Lever – Used to start the engine.

(3) Fuel Valve – Turn this valve to the “ON” position to

supply fuel to the engine.

(4) Air Filter – Protects the engine by filtering dust

and debris from the intake air.

(5) Recoil Starter – Used to start the engine.

(6) Low Oil Sensor – Senses the level of oil in the

crankcase and shuts the engine down if the level

falls too low.

(7) Oil Filler Cap – Check and fill engine oil level.

(8) Power Panel – See “Power Panel.”

(9) Handle

Generator

CONTROLS AND FEATURES

1

5

4

7

8

9

3

2

6

6

100100 ENGLISH

Power Panel

CONTROLS AND FEATURES

(1) Engine Switch – Flip the switch to the “On”

position and pull the recoil starter to start the

generator. Turn to the “Off” position to turn off the

generator.

(2) Intelligauge – Tri-mode digital display for running

hours, voltage and hertz.

(3) Circuit Breakers – Protects the generator against

electrical overload.

(4) Ground Terminal – Consult an electrician for local

grounding regulations.

(5) 120V, 30A Twist-Lock (NEMA L5-30R) – May be

used to supply electrical power for the operation

of 120 Volt AC, 30 Amp, single phase 60 Hz

electrical loads.

(6) 120V, 20A Duplex (2) – (NEMA 5-20R) May be

used to supply electrical power for the operation

of 120 Volt AC, 20 Amp, single phase 60 Hz

electrical loads.

21

4 5 6

3

7

ENGLISH 100100

Parts Included

Your 100100 gasoline powered generator ships with the

following parts:

Wheel Kit

– 20.3 cm (8 in.) Wheel .................... 2

– Bushing . ............................. 2

– Flange Bolt (M10x105 for Wheel) ............ 2

– Flat Washer Ø10 ........................ 2

– Lock Nut (M10) ........................ 2

– Support Leg w/Vibration Mounts ............. 1

– Flange Bolt (M8x16 for Support Leg) .......... 2

– Handle .............................. 1

– Flange Bolt (M8x45 for Handle) ............. 2

– Flange Lock Nut (M8) .................... 4

Other

– Oil Funnel ............................ 1

– Oil ...................... 600 mL (0.6 qt.)

– RV Adapter Plug ........................ 1

CONTROLS AND FEATURES

8

100100 ENGLISH

Your generator requires some assembly. This unit ships

from our factory without oil. It must be properly serviced

with fuel and oil before operation.

If you have any questions regarding the assembly of your

generator, call our help line at 1-877-338-0999. Please

have your serial number and model number available.

Remove the Generator from the Shipping Carton

1. Set the shipping carton on a solid, flat surface.

2. Remove everything from the carton except the

generator.

3. Carefully cut each corner of the box from top to

bottom. Fold each side flat on the ground to provide a

surface area to install the wheel kit and support leg.

Install the Wheel Kit

You will need the following tools to install the wheels:

s 17 mm wrench OR adjustable wrench (not included)

s Socket wrench with a 16 mm socket (not included)

s Pliers (not included)

1. Before adding fuel and oil, tip the generator on it’s side.

2. Slide the flange bolt (M10x105) through the washer,

sleeve and wheel.

3. Slide the bolt through the mount point on the frame.

4. Fasten securely with the M10 lock nut.

5. Repeat steps 2-4 to attach the second wheel.

Install the Support Leg

1. Attach the support leg to the generator frame with

flange bolts (M8x16) and flange lock nuts (M8).

2. Tip the generator slowly so that it rests on the

wheels and support leg.

The wheel kit is not intended for over-the-road use.

CAUTION

ASSEMBLY

Install the Handle

1. Place the handle over the mounting channel on the

frame.

2. Secure the handle to the frame using the two handle

flange bolts (M8x45).

3. Place a flange lock nut (M8) on the end of each bolt

and fasten securely. DO NOT over tighten the flange

lock nuts.

9

ENGLISH 100100

ASSEMBLY

Add Engine Oil Add Engine Oil Cont’d.

1. Place the generator on a flat, level surface.

2. Remove oil fill cap/dipstick to add oil.

3. Add up to 600 mL (0.6 qt.) of oil (included) and

replace oil fill cap/dipstick. DO NOT OVERFILL.

4. Check engine oil level daily and add as needed.

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

CAUTION

DO NOT attempt to crank or start the engine before

it has been properly filled with the recommended

type and amount of oil. Damage to the generator as

a result of failure to follow these instructions will

void your warranty.

CAUTION

Check oil often during the break-in period. Refer to the

Maintenance section for recommended service intervals.

NOTE

The generator rotor has a sealed, pre-lubricated ball

bearing that requires no additional lubrication for

the life of the bearing.

NOTE

The recommended oil type is 10W-30 automotive oil.

NOTE

Synthetic oil may be used after the 5 hour initial

break-in period. Using synthetic oil does not

increase the recommended oil change interval.

NOTE

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings. After the 5 hour break-in period,

change the oil.

NOTE

Once oil has been added, a visual check should show

oil about 1-2 threads from running out of the fill hole.

If using the dipstick to check oil level, DO NOT screw

in the dipstick while checking.

NOTE Weather will affect engine oil and engine

performance. Change the type of engine oil used

based on weather conditions to suit the engine

needs.

NOTE

Full Synthetic 5W-30

Degrees Celsiusº (Outside)

(Outside)

Degrees Fahrenheitº

10

100100 ENGLISH

ASSEMBLY

Grounding

Your generator must be properly connected to an

appropriate ground to help prevent electric shock.

A ground terminal connected to the frame of the generator

has been provided on the power panel. For remote

grounding, connect of a length of heavy gauge (12 AWG

minimum) copper wire between the generator ground

terminal and a copper rod driven into the ground. We

strongly recommend that you consult with a qualified

electrician to ensure compliance with local electrical codes.

Failure to properly ground the generator can result in

electric shock.

WARNING

Our engines work well with 10% or less ethanol

blend fuels. When using blended fuels there are

some issues worth noting:

– Ethanol-gasoline blends can absorb more water

than gasoline alone.

– These blends can eventually separate, leaving

water or a watery goo in the tank, fuel valve and

carburetor.

– With gravity-fed fuel supplies, this compromised

fuel can be drawn into the carburetor and cause

damage to the engine and/or potential hazards.

– There are only a few suppliers of fuel stabilizer

that are formulated to work with ethanol blend

fuels.

– Any damages or hazards caused by using

improper fuel, improperly stored fuel, and/

or improperly formulated stabilizers, are not

covered by manufacture’s warranty.

It is advisable to always shut off the fuel supply,

run the engine to fuel starvation and drain the tank

when the equipment is not in use for more than 30

days.

NOTE

Add Fuel Cont’d.

Add Fuel

1. Use clean, fresh, regular unleaded fuel with a

minimum octane rating of 85 and an ethanol content

of less than 10% by volume.

2. DO NOT mix oil with fuel.

3. Clean the area around the fuel cap.

4. Remove the fuel cap.

5. Slowly add fuel to the tank. DO NOT OVERFILL. Fuel

can expand after filling. A minimum of 6.4 mm (¼ in.)

of space left in the tank is required for fuel expansion,

more than 6.4 mm (¼ in.) is recommended. Fuel can

be forced out of the tank as a result of expansion if it is

overfilled, and can affect the stable running condition of

the product. When filling the tank, it is recommended

to leave enough space for the fuel to expand.

6. Screw on the fuel cap and wipe away any spilled fuel.

Use regular unleaded gasoline with a minimum

octane rating of 85.

Do not mix oil and gasoline.

Fill tank to approximately 6.4 mm (¼ in.) below the

top of the tank to allow for fuel expansion.

DO NOT pump gas directly into the generator at the

gas station. Use an approved container to transfer

the fuel to the generator.

DO NOT fill fuel tank indoors.

DO NOT fill fuel tank when the engine is running or hot.

DO NOT overfill the fuel tank.

DO NOT light cigarettes or smoke when filling the

fuel tank.

CAUTION

Pouring fuel too fast through the fuel screen may

result in blow back of fuel at the operator while filling.

WARNING

11

ENGLISH 100100

Generator Location

NEVER operate the generator inside any building,

including garages, basements, crawlspaces and sheds,

enclosure or compartment, including the generator

compartment of a recreational vehicle. Please consult

your local authority. In some areas, generators must

be registered with the local utility. Generators used at

construction sites may be subject to additional rules and

regulations. Generators should be on a flat, level surface

at all times (even while not in operation). Generators

must have at least 1.5 m (5 ft.) of clearance from all

combustible material. In addition to clearance from all

combustible material, generators must also have at least

91.4 cm (3 ft.) of clearance on all sides to allow for

adequate cooling, maintenance and servicing. Generators

should never be started or operated in the back of a

SUV, camper, trailer, in the bed of a truck (regular, flat

or otherwise), under staircases/stairwells, next to walls

or buildings, or in any other location that will not allow

for adequate cooling of the generator and/or the muffler.

DO NOT contain generators during operation. Allow

generators to properly cool before transport or storage.

Place the generator in a well-ventilated area. DO NOT

place the generator near vents or intakes where exhaust

fumes could be drawn into occupied or confined spaces.

Carefully consider wind and air currents when positioning

generator.

Failure to follow proper safety precautions may void

manufacturer’s warranty.

Do not operate or store the generator in rain, snow,

or wet weather.

Using a generator or electrical appliance in wet

conditions, such as rain or snow, or near a pool or

sprinkler system, or when your hands are wet, could

result in electrocution.

WARNING

WARNING

During operation the muffler and exhaust fumes

produced will become hot. If adequate cooling and

breathing space are not supplied, or if the generator

is blocked or contained, temperatures can become

extremely heated and may lead to fire.

OPERATION

Surge Protection

Electronic devices, including computers and many

programmable appliances use components that are

designed to operate within a narrow voltage range and

may be affected by momentary voltage fluctuations.

While there is no way to prevent voltage fluctuations, you

can take steps to protect sensitive electronic equipment.

1. Install UL1449, CSA-listed, plug-in surge suppressors

on the outlets feeding your sensitive equipment.

Surge suppressors come in single- or multi-outlet

styles. They’re designed to protect against virtually

all short-duration voltage fluctuations.

Voltage fluctuation may impair the proper

functioning of sensitive electronic equipment.

CAUTION

Grounding

The generator system ground connects the frame to the

ground terminals on the power panel.

– The generator (stator winding) is isolated from the

frame and from the AC receptacle ground pin.

– Electrical devices that require a grounded receptacle

pin connection will not function if the receptacle ground

pin is not functional.

12

100100 ENGLISH

Connecting Electrical Loads

1. Let the engine stabilize and warm up for a few

minutes after starting

2. Plug in and turn on the desired 120 Volt AC single

phase, 60 Hz electrical loads.

– DO NOT connect 3-phase loads to the generator.

– DO NOT connect 50 Hz loads to the generator.

– DO NOT overload the generator.

Connecting a generator to your electric utility

company’s power lines or to another power source

may be against the law. In addition this action,

if done incorrectly, could damage your generator

and appliances and could cause serious injury or

even death to you or a utility worker who may be

working on nearby power lines. If you plan to run a

portable electric generator during an outage, please

notify your electric utility company immediately

and remember to plug your appliances directly

into the generator. Do not plug the generator into

any electric outlet in your home. Doing so could

create a connection to the utility company power

lines. You are responsible for ensuring that your

generator’s electricity does not feed back into the

electric utility power lines.

If the generator will be connected to a building

electrical system, consult your local utility company

or a qualified electrician. Connections must isolate

generator power from utility power and must comply

with all applicable laws and codes.

NOTE

Stopping the Engine

1. Turn off and unplug all electrical loads. Never start

or stop the generator with electrical devices plugged

in or turned on.

2. Let the generator run at no-load for several minutes

to stabilize internal temperatures of the engine and

generator.

3. Turn the fuel valve to the “OFF” position.

4. Let the engine run until fuel starvation has stopped

the engine. This usually takes a few minutes.

5. Press the engine switch to the “OFF” position.

Important: Always ensure that the Fuel Valve and the

Engine Switch are in the “OFF” position when the engine

is not in use.

If the engine will not be used for a period of two (2) weeks

or longer, please see the Storage section for proper engine

and fuel storage.

NOTE

Starting the Engine

1. Make certain the generator is on a flat, level surface.

2. Disconnect all electrical loads from the generator.

Never start or stop the generator with electrical

devices plugged in or turned on.

3. Turn the fuel valve to the “ON” position.

4. Flip the engine switch to the “ON” position.

5. Move the choke lever to the “CHOKE” position.

6. Pull the starter cord slowly until resistance is felt and

then pull rapidly

7. Do not over-choke. As as soon as engine starts, move

the choke lever to the “RUN” position.

If the engine starts but does not run make certain

that the generator is on a flat, level surface. The

engine is equipped with a low oil sensor that will

prevent the engine from running when the oil level

falls below a critical threshold.

NOTE

Keep choke lever in “Choke” position for only 1

pull of the recoil starter. After first pull, move choke

lever to the “Run” position for up to the next 3

pulls of the recoil starter. Too much choke leads to

sparkplug fouling/engine flooding due to the lack of

incoming air. This will cause the engine not to start.

NOTE

OPERATION

13

ENGLISH 100100

Do Not Overload Generator

Capacity

Follow these simple steps to calculate the running and

starting watts necessary for your purposes.

1. Select the electrical devices you plan on running at

the same time.

2. Total the running watts of these items. This is

the amount of power you need to keep your items

running.

3. Identify the highest starting wattage of all devices

identified in step 1. Add this number to the number

calculated in step 2. Surge wattage is the extra

burst of power needed to start some electric driven

equipment. Following the steps listed under “Power

Management” will guarantee that only one device will

be starting at a time.

Power Management

Use the following formula to convert voltage and

amperage to watts:

Volts x Amps = Watts

To prolong the life of your generator and attached

devices, follow these steps to add electrical load:

1. Start the generator with no electrical load attached

2. Allow the engine to run for several minutes to stabilize.

3. Plug in and turn on the first item. It is best to attach

the item with the largest load first.

4. Allow the engine to stabilize.

5. Plug in and turn on the next item.

6. Allow the engine to stabilize.

7. Repeat steps 5-6 for each additional item.

Never exceed the specified capacity when adding

loads to the generator.

NOTE

OPERATION

14

100100 ENGLISH

Air Filter

1. Remove the snap-on cover holding the air filter to

the assembly.

2. Remove the foam element.

3. Wash in liquid detergent and water. Squeeze

thoroughly dry in a clean cloth.

4. Saturate in clean engine oil.

5. Squeeze in a clean, absorbent cloth to remove all

excess oil.

6. Place the filter in the assembly.

7. Reattach the air filter cover and snap in place.

The owner/operator is responsible for all periodic

maintenance.

Complete all scheduled maintenance in a timely manner.

Correct any issue before operating the generator.

Never operate a damaged or defective generator.

Tampering with the factory set governor will void

your warranty.

Engine Maintenance

To prevent accidental starting, remove and ground spark

plug wire before performing any service.

Oil

Change oil when the engine is warm. Refer to the oil

specification to select the proper grade of oil for your

operating environment.

1. Remove the oil drain plug with a 12 mm (0.5 in.)

socket and extension.

2. Allow the oil to drain completely.

3. Replace the drain plug.

4. Remove oil fill cap/dipstick to add oil.

5. Add up to 600 mL (0.6 qt) of oil and replace oil fill

cap/dipstick. DO NOT OVERFILL.

6. Dispose of used oil at an approved waste

management facility.

Spark Plugs

1. Remove the spark plug cable from the spark plug.

2. Use the spark plug tool (not included) to remove the

plug.

3. Inspect the electrode on the plug. It must be clean and

not worn to produce the spark required for ignition.

4. Make certain the spark plug gap is 0.7 - 0.8 mm

(0.028 - 0.031 in.).

5. Refer to the spark plug recommendation in

Specifications section when replacing the plug.

6. Carefully thread the plug into the engine.

7. Use the spark plug tool (not included) to firmly install

the plug.

8. Attach the spark plug wire to the plug.

For service or parts assistance, contact our help

line at 1-877-338-0999

NOTE

Maintenance, replacement, or repair of emission

control devices and systems may be performed

by any non-road engine repair establishment or

individual.

NOTE

Once oil has been added, a visual check should show

oil about 1-2 threads from running out of the fill hole.

If using the dipstick to check oil level, DO NOT screw

in the dipstick while checking.

NOTE

WARNING

WARNING

Improper maintenance will void your warranty.

WARNING

Oil Cont’d.

MAINTENANCE AND STORAGE

0.7-0.8 mm

0.028-0.031 in.

15

ENGLISH 100100

Maintenance Schedule

Follow the service intervals indicated in the following

maintenance schedule.

Service your generator more frequently when operating

in adverse conditions.

Contact our help line at 1-877-3 38-0 999 to locate the

nearest Champion Power Equipment certified service

dealer for your generator or engine maintenance needs.

Adjustments

The air-fuel mixture is not adjustable. Tampering with

the governor can damage your generator and your

electrical devices and will void your warranty. CPE

recommends that you contact our service line at

1-877-33 8-0999 for all other service and/or adjustment

needs.

Cleaning

DO NOT spray engine with water.

CAUTION

Water can contaminate the fuel system.

MAINTENANCE AND STORAGE

Failure to clean the spark arrester will result in

degraded engine performance.

CAUTION

Use a damp cloth to clean exterior surfaces of the engine.

Use a soft bristle brush to remove dirt and oil.

Use an air compressor (25 PSI) to clear dirt and debris

from the engine.

Spark Arrester

1. Allow the engine to cool completely before servicing

the spark arrester.

2. Remove the screws (3) holding the cover plate which

retains the end of the spark arrester to the muffler.

3. Remove the spark arrester screen.

4. Carefully remove the carbon deposits from the spark

arrester screen with a wire brush.

5. Replace the spark arrester if it is damaged.

6. Position the spark arrester in the muffler and attach

with the screws (3).

*To be performed by knowledgeable, experienced owners or

Champion Power Equipment certified dealers.

Every 8 hours or daily

Check oil level

Clean around air intake and muffler

First 5 hours

Change oil

Every 50 hours or every season

Clean air filter

Change oil if operating under heavy load or in hot environments

Every 100 hours or every season

Change oil

Clean/adjust spark plug

Check/adjust valve clearance*

Clean spark arrester

Clean fuel tank and filter*

Every 250 hours

Clean combustion chamber*

Every 3 years

Replace fuel line

16

100100 ENGLISH

MAINTENANCE AND STORAGE

Generator Maintenance

Make certain that the generator is kept clean and stored

properly. Only operate the unit on a flat, level surface in

a clean, dry operating environment. DO NOT expose the

unit to extreme conditions, excessive dust, dirt, moisture

or corrosive vapours.

Use a damp cloth to clean exterior surfaces of the generator.

Use a soft bristle brush to remove dirt and oil.

Use an air compressor (25 PSI) to clear dirt and debris

from the generator.

Inspect all air vents and cooling slots to ensure that they

are clean and unobstructed.

Generator exhaust contains odourless and

colourless carbon monoxide gas.

To avoid accidental or unintended ignition of your

generator during periods of storage, the following

precautions should be followed:

– When storing the generator for short or extended

periods of time make sure that the Engine

Switch and the Fuel Valve are set in the OFF

position.

DANGER

Storage

The generator should be started at least once every 14

days and allowed to run for at least 20 minutes. For

longer term storage, please follow these guidelines.

Generator Storage

1. Add a properly formulated fuel stabilizer to the tank.

2. Be sure all appliances are disconnected from the

generator.

3. Run the generator for a few minutes so the treated

fuel cycles through the fuel system and carburetor.

4. Turn the fuel valve to the “Off” position.

5. Let the generator run until fuel starvation has

stopped the engine. This usually takes a few minutes.

6. The generator needs to cool completely before

cleaning and storage.

7. Clean the generator according to the maintenance section.

8. Change the oil.

9. Remove the spark plug and pour about 14.8 mL

(1⁄2 ounce) of oil into the cylinder. Crank the engine

slowly to distribute the oil and lubricate the cylinder.

10. Reattach the spark plug.

11. Store the unit in a clean, dry place out of direct

sunlight.

Our engines work well with 10% or less ethanol

blend fuels. When using blended fuels there are

some issues worth noting:

– Ethanol-gasoline blends can absorb more water

than gasoline alone.

– These blends can eventually separate, leaving

water or a watery goo in the tank, fuel valve and

carburetor.

– With gravity-fed fuel supplies, this compromised

fuel can be drawn into the carburetor and cause

damage to the engine and/or potential hazards.

– There are only a few suppliers of fuel stabilizer

that are formulated to work with ethanol blend

fuels.

– Any damages or hazards caused by using

improper fuel, improperly stored fuel, and/

or improperly formulated stabilizers, are not

covered by manufacture’s warranty.

It is advisable to always shut off the fuel supply,

run the engine to fuel starvation and drain the tank

when the equipment is not in use for more than 30

days.

NOTE

Generator Storage Cont’d.

DO NOT use a garden hose to clean the generator.

Water can enter the generator through the cooling

slots and damage the generator windings.

CAUTION

17

ENGLISH 100100

Oil

Use 10W-30 automotive oil.

Oil capacity is up to 600 mL (0.6 qt).

DO NOT OVERFILL.

Please reference the following chart for recommended

oil types for use in the generator.

Fuel

Fuel capacity is 13 L (3.4 gallons). Use regular

unleaded gasoline with a minimum octane rating of 85

and an ethanol content of less than 10% by volume.

Generator Specifications

– Model .......................... 100100

– Rated Wattage .................. 3250 Watts

– Starting Wattage . ................ 4000 Watts

– AC Voltage ......................... 120 V

– Phase ............................ Single

– Frequency ......................... 60 Hz

– Fuel Capacity ............... 13 L (3.4 gallons)

– Gross Weight .............. 50.7 kg (111.8 lb.)

– Net Weight . ................ 46.3 kg (102 lb.)

– Height . .................. 57.2 cm (22.5 in.)

– Width ................... 60.1 cm (23.7 in.)

– Length. . . . . . . . . . . . . . . . . . . 66.8 cm (26.3 in.)

SPECIFICATIONS

Engine Specifications

– Model ...................... YF172FD-010

– Displacement ....................... 224cc

– Type ........................ 4-Stroke OHV

– Start Type ......................... Recoil

Maintenance Valve Clearance

– Intake: 0.13 – 0.17 mm (0.005 – 0.007 in.)

– Exhaust: 0.18 – 0.22 mm (0.007 – 0.009 in.)

Note: Tech bulletin regarding the valve adjustment

procedure is on www.championpowerequipment.com.

Spark Plugs

OEM spark plug: NHSP F6RTC

Replacement spark plug: NGK BPR6ES or equivalent

Make certain the spark plug gap is 0.7 - 0.8 mm

(0.028 - 0.031 in.).

An Important Message About Temperature

Your Champion Power Equipment product is designed

and rated for continuous operation at ambient

temperatures up to 40°C (104°F). When your product is

needed your product may be operated at temperatures

ranging from -15°C (5°F) to 50°C (122°F) for short

periods. If the product is exposed to temperatures

outside this range during storage, it should be brought

back within this range before operation. In any event,

the product must always be operated outdoors, in a

well-ventilated area and away from doors, windows and

other vents.

Weather will affect engine oil and engine

performance. Change the type of engine oil used

based on weather conditions to suit the engine

needs.

NOTE

Full Synthetic 5W-30

Degrees Celsiusº (Outside)

(Outside)

Degrees Fahrenheitº

18

100100 ENGLISH

Wiring Diagram

SPECIFICATIONS

CIRCUIT BREAKER

GENERATOR BLOCK

G

W

R

B

Y

L

INDIGO

BLACK WHITE

WHITE GREEN

GREEN YELLOW

WHITE BLUE

G/YGREEN

WHITE

RED

In

W/L

BLACK

YELLOW

BLUE

Br

W/G

B/W

BROWN

IGNITION COIL

SPARKING PLUG

ENGINE BLOCK B

EXW

FW

MW1

L

+

Y

Y

AVR

Br

30A

OIL LEVEL SW

YCONTROL BOX BLOCK

Y

G/Y

EARTH

TERMINAL

G/Y

ENG SW

R

Ww

G/Y

B

Y

Y

L

L

R

W

ww

120V

20A

CIRCUIT BREAKER

L5-30R

R R R

R

R

120V

5-20R

R

B

MW2

Y

G/Y

B

Transition

R

W

B

R

R

w

Intelligauge

120V

5-20R

R

w

19

ENGLISH 100100

Parts Diagram

SPECIFICATIONS

1

282930

31

323334

35

36

37

38

39

40

41

4243

44

45

46

47

88

89

90

2

3

4

5

67

8

9

10

11

12

13

14

15

16

17 18 19 20

14

21

17 18

22

23

13

48

49

50

51

52

5354

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

71

72

73

74

7576

78

79

81

82

83

84

85

86

80

77

24

25

27 26

50

50

70

92

87

91

20

100100 ENGLISH Parts List

#Part Number Description Qty

127.403 Engine 1

2122.190005.00 Rubber, Fore-Cover, B 1

3122.190005.01 Rubber, Fore-Cover, A 1

4124.191100.02 Rotor Assembly, Al, 130 mm,

CSA 1

52.08.109 Flange Bolt M8×252 1

61.96.08 Big Washer Ø8 1

71.7244.08 Big Lock Waher Ø8 1

8124.191200.02 Stator Assembly, Al, 130 mm,

CSA 1

9124.191002.01 Stator Cover 1

10 122.190002.00 End Housing 1

11 2.08.032 Flange Bolt M6×179 4

12 1.97.1.06 Washer Ø6 4

13 1.93.06 Lock Waher Ø6 8

14 1.16674.0512.2 Flange Bolt M5×12 3

15 122.190400.00 Terminal Block 1

16 1.97.1.05 Washer Ø5 2

17 1.93.05 Lock Waher Ø5 3

18 1.5783.0516 Bolt M5×16 3

19 122.190200.04 AVR 1

20 1.16674.0516 Flange Bolt M5×16 2

21 122.190003.00.48 Generator End Cover, Yellow 1

22 122.190004.01 Pinch, Carbon Brush 1

23 122.190300.00 Carbon Brush Assembly 1

24 1.5789.0612 Flange Bolt M6×12 3

25 27.100100.01 Bracket, Muffler 1

26 1.823.0406 Screw M4×63

27 27.101300.00 Spark Arrester Assembly 1

28 27.101000.01 Muffler Assembly 1

29 1.6175.08 Nut M8 2

30 1.93.08 Lock Washer Ø8 2

31 1.848.08 Washer Ø8 2

32 26.100001.00 Gasket, Exhaust 1

33 1.5789.0608 Flange Bolt M6×81

34 23.090006.21 Holder, Air Cleaner 1

35 122.071000.31.48 Fuel Tank, Yellow 1

36 122.070015.01 Mount Vibration, Fuel Tank 4

37 2.03.004 Washer (Ø24×Ø6.5×1.5) 4

38 1.5789.0620.2 Flange Bolt M6×20 4

39 24.070800.00 Reversal Valve 1

40 2.06.006 Clamp (Ø7×Ø1) 1

41 24.070030.00 Hole, Breather Tube 1

42 122.070014.02 Pipe, Reversal Valve (670 mm) 1

43 122.070100.07 Fuel Tank Cap 1

44 122.070300.03 Fuel Filter 1

45 2.06.007 Clamp (Ø8×b6) 2

46 23.070011.04 Pipe, Fuel, 155 mm 1

47 122.070400.05 Fuel Valve 1

#Part Number Description Qty

48 152.200702.00 Cover, Handle 1

49 122.200700.03.2 Handle 1

50 1.6177.1.08 Flange Lock Nut M8 14

51 1.5789.0845 Flange Bolt M8×45 2

52 6.2.288.328.2 Frame 1

53 2.05.001 Clamp (Ø8×6.5) 2

54 122.201200.02 Motor Mount, II 2

55 122.201200.03 Motor Mount, I 2

56 1.6182.10 Lock Nut M10 2

57 122.201701.07.2 20.3 cm (8 in.) Wheel, Black,

PU 2

58 122.200016.01 Bushing (Ø16×Ø10.5×58.5) 2

59 1.96.10 Washer Ø10 2

60 1.5782.10105 Bolt M10×105 2

61 1.6177.1.06 Flange Lock Nut M6 1

62 5.1900.029 Grounding Line 150 mm 1

63 1.862.06 Lock Washer Ø6 1

64 1.5789.0612 Flange Bolt M6×12 1

65 1.5789.0816 Flange Bolt M8×16 2

66 152.200002.00.2 Support Leg 60 mm 1

67 152.201400.00 Rubber, Support 2

68 1.5789.0825 Flange Bolt M8×25 2

69 122.210002.26 Control Box 1

70 1.5789.0615.1 Bolt M6×15, Black 4

71 1.818.0514.2 Screw M5×14, Black 1

72 5.1810.000 Over Voltage Protector 1

73 122.20.1.2 Control Panel, Black 1

74 5.1000.004.3 Ignition Switch, Red 1

75 1.9074.4.0414.1 Screw/Washer Assembly M4×14,

Black 2

76 1.6177.1.04.1 Flange Lock Nut M4, Black 8

77 1.9074.4.0512.1 Screw/Washer Assembly M5×12,

Black 5

78 5.1430.001 Intelligauge 1

79 5.1210.930 AC 30A Breaker, Push Button 1

80 5.1210.920 AC 20A Breaker, Push Button 1

81 1.5783.0514.3 Bolt M5×14, Green 1

82 1.6170.05.3 Nut M5, Green 2

83 1.97.1.05.3 Washer Ø5, Green 1

84 1.862.05 Lock Washer Ø5 1

85 5.1120.023 Receptacle L5-30R, CSA 1

86 5.1120.027 Receptacle 5-20R, Duplex, CSA 2

87 100100.21.10 Wire Assembly 1

88 122.210003.02 Wire Jacket, Control Box 1

89 5.1310.003 Conduit, Metal, CSA, 160 mm 1

90 122.210003.04 Plug, Control Box 1

91 100100.21 Control Panel Assembly 1

92 9.3000.916 RV Plug Adapter, L5-30 - TT-30 1

21

ENGLISH 100100

Engine Parts Diagram

SPECIFICATIONS

1

2345678910

12 13

2526 27 2930 3235 37

38 12 40 41

42

43 44

46

47

21 22

2324

31

34 36 39

53

52

45

51

50

4955

56

57

58

54

6062

61

63

65

66

67

68

69

7071

72

74

25

93

94

95

92

91

90

97

78

79

80

82

83

84

85

5

86

87

88

76

59

12

77

77

96

33

81

73

15

20

48 14

101

51

100

64

16

99

89

19

11

18

17

19

28

98

75

103

102

104

26

10

22

100100 ENGLISH Parts List

#Part Number Description Qty

11.5789.0608 Flange Bolt M6×83

222.061100.00.2 Recoil Starter Cover, Black 1

321.061005.00 Recoil Starter Spring 1

42.10.003 Rope (Ø5×1550) 1

521.061001.01 Recoil Starter Reel 1

645.060003.00 Spring, Ratchet 2

745.060002.00 Starter Ratchet (Iron) 2

845.060009.00 Spring Guide, Ratchet 1

945.060007.00 Ratchet Guide 1

10 45.060008.00 Screw, Ratchet Guide 1

11 24.040004.00 Guide Plate Push Rod 1

12 1.5789.0612 Flange Bolt M6×12 8

13 27.080100.02.48 Fan Cover, Yellow 1

14 24.091100.21 Base, Air Cleaner 1

15 21.061300.00 Recoil Handle 1

16 24.130004.20 Gasket, Air Cleaner 1

17 22.061000.00 Recoil Assembly 1

18 27.091000.02 Air Cleaner Assembly 1

19 27.131000.01 Carburetor 1

20 2.03.016 Washer, Drain Bolt (Ø10×Ø16×1.5) 1

21 2.02.006 Nut M14×1.5 1

22 83.060001.01 Pulley, Starter 1

23 27.080001.00 Cooling Fan 1

24 24.120100.06 Flywheel 1

25 2.11.001 Oil Seal (Ø25×Ø41.3×6) 2

26 2.03.020.1 Washer (Ø6.2×Ø15×0.5), Black 2

27 21.110100.00 Gear, Governor 1

28 23.130100.20 Choke Lever 1

29 21.110013.00 Shaft, Governor Gear 1

30 21.110011.00 Clip, Governor Gear 1

31 22.130003.00 Gasket, Carburetor 1

32 21.110012.01 Bushing, Govornor Gear (Iron) 1

33 24.130002.00 Gasket, Insulator 1

34 27.130001.00 Insulator, Carburetor 1

35 23.080600.00 Air Guide, Right Side 1

36 2.01.009 Stud Bolt M6×110 2

37 27.030100.01 Crankcase 1

38 21.127000.02 Oil Level Sensor 1

39 26.010100.01 Cylinder Head 1

40 27.050200.00 Connecting Rod 1

41 27.050100.00 Crankshaft 1

42 1.276.6205 Bearing 6205 2

43 24.030008.00 Gasket, Crankcase Cover 1

44 22.031000.00.48 Oil Dipstick Assembly, Yellow 1

45 2.03.021.1 Washer (Ø6.4×Ø13×1), Black 1

46 27.030007.01 Cover, Crankcase 1

47 1.5789.0832.0.8 Flange Bolt M8×32 5

48 23.091002.21 Seal, Air Cleaner 1

49 23.110006.00 Rod, Governor 1

50 27.110003.00 Governor Arm 1

51 1.6177.06 Flange Nut M6 3

52 21.110001.00 Shaft, Governor Arm 1

53 22.123000.02 Ignition Coil (Shield EPA) 1

#Part Number Description Qty

54 1.5789.0625 Flange Bolt M6×25 2

55 23.110005.01 Spring, Throttle Return 1

56 23.110007.00 Spring, Governor 1

57 2.08.040 Bolt, Governor Arm (M6×21) 1

58 21.110008.00 Pin, Shaft 1

59 27.111000.20 Control Assembly 1

60 25.040013.00 Lifter, Valve 2

61 2.04.001 Dowel Pin (Ø9×14) 2

62 27.041000.00 Camshaft 1

63 2.14.012 Woodruff Key (4×7.5×19) 1

64 2.08.037 Bolt, Drain (M10×1.25×25) 1

65 27.050005.00 Piston 1

66 23.050003.00 Pin, Piston 1

67 2.09.001 Circlip (Ø18×Ø1) 2

68 27.050303.00 Ring, Oil 1

69 27.050302.00 Ring, Second Piston 1

70 27.050301.00 Ring, First Piston 1

71 27.030009.01 Gasket, Cylinder Head 1

72 2.04.003 Dowel Pin (Ø10×14) 2

73 23.040002.02 Valve, Intake 1

74 23.040006.02 Valve, Exhaust 1

75 27.080200.00 Air Shroud, Cylinder 1

76 2.15.002(F6RTC) Spark Plug (F6RTC) 1

77 1.5789.0865 Flange Bolt M8×65 3

78 23.040017.00 Oil Seal, Valve 2

79 21.040003.00 Spring, Valve 2

80 21.040007.00 Retainer, Exhaust Valve Spring 1

81 21.040001.00 Retainer, Intake Valve Spring 1

82 21.040008.00 Rotator, Exhaust Valve 1

83 24.040202.00 Shaft, Rocker Arm 1

84 22.040009.00 Rocker Arm 2

85 22.040012.00 Screw, Valve Adjustment 2

86 21.040021.00 Nut, Lock (M6×0.5) 2

87 1.97.1.06 Washer Ø6 2

88 1.6177.1.06 Flange Lock Nut M6 2

89 27.131017.00 Standard Main Jet 1

90 24.040201.00 Retainer, Rocker Arm 1

91 23.040010.00 Bolt, Rocker Arm 2

92 27.040005.00 Push Rod 2

93 21.020002.01 Gasket, Cylinder Head Cover 1

94 24.021000.00 Cylinder Head Cover (CPE) 1

95 23.020001.02 Breather Tube 1

96 1.5789.0615 Flange Bolt M6×15 4

97 2.01.010 Stud Bolt M8×35 2

98 1.5789.0620 Flange Bolt M6×20 1

99 27.091200.01 Cover, Air Cleaner 1

100 23.091003.21 Element, Air Cleaner 1

101 23.091001.21 Separator, Air Cleaner 1

102 27.030013.00 Seal Strip, Crankcase Cover 1

103 27.030013.01 Seal Strip, Crankcase Cover 1

104 1.5789.0840.0.8 Flange Bolt M8×40 1

105 1.16674.1065 Flange Bolt M10×65 1

23

ENGLISH 100100

Problem Cause Solution

Generator will not start No fuel Add fuel

Faulty spark plug Replace spark plug

Unit loaded during start up Remove load from unit

Generator will not start;

Generator starts but runs roughly

Low oil level Fill crankcase to the proper level

Place generator on a flat, level surface

Choke in the wrong position Adjust choke

Spark plug wire loose Attach wire to spark plug

Generator shuts down during operation Out of fuel Fill fuel tank

Low oil level Fill crankcase to the proper level.

Place generator on a flat, level surface

Generator cannot supply enough

power or overheating

Generator is overloaded Review load and adjust. See “Power

Management”

Insufficient ventilation Check for air restriction. Move to a

well ventilated area

No AC output Cable not properly connected Check all connections

Connected device is defective Replace defective device

Circuit breaker is open Reset circuit breaker

Faulty brush assembly Replace brush assembly (Service

Centre)

Faulty AVR (auto voltage regulator) Replace AVR (Service Centre)

Loose wiring Inspect and tighten wiring connections

Other Contact the help line

Generator gallops Engine governor defective Contact the help line

Repeated circuit breaker tripping Overload Review load and adjust. See “Power

Management”

Faulty cords or device Check for damaged, bare or frayed

wires. Replace defective device

TROUBLESHOOTING

For further technical support:

Technical Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)

Toll Free : 1-877-338-0999

tech@championpowerequipment.com

24

100100 ENGLISH

WARRANTY

CHAMPION POWER EQUIPMENT

2 YEAR LIMITED WARRANTY

Warranty Qualifications

Champion Power Equipment (CPE) will register this

warranty upon receipt of your Warranty Registration Card

and a copy of your sales receipt from one of CPE’s retail

locations as proof of purchase.

Please submit your warranty registration and your proof

of purchase within ten (10) days of the date of purchase.

Repair/Replacement Warranty

CPE warrants to the original purchaser that the

mechanical and electrical components will be free of

defects in material and workmanship for a period of one

year (parts and labour) and two years (parts) from the

original date of purchase (90 days (parts and labour)

and 180 days (parts) for commercial and industrial

use). Transportation charges on product submitted

for repair or replacement under this warranty are the

sole responsibility of the purchaser. This warranty only

applies to the original purchaser and is not transferable.

Do Not Return Unit To Place Of Purchase

Contact CPE’s Technical Service and CPE will

troubleshoot any issue via phone or e-mail. If the

problem is not corrected by this method, CPE will, at its

option, authorize evaluation, repair or replacement of the

defective part or component at a CPE Service Centre.

CPE will provide you with a case number for warranty

service. Please keep it for future reference. Repairs

or replacements without prior authorization, or at an

unauthorized repair facility, will not be covered by this

warranty.

Warranty Exclusions

This warranty does not cover the following repairs and

equipment:

Normal Wear

Generators need periodic parts and service to perform well.

This warranty does not cover repair when normal use has

exhausted the life of a part or the equipment as a whole.

Installation, Use and Maintenance

This warranty will not apply to parts and/or labour if this

generator is deemed to have been misused, neglected,

involved in an accident, abused, loaded beyond the

generator’s limits, modified, installed improperly or

connected incorrectly to any electrical component.

Installation, Use and Maintenance Cont’d.

Normal maintenance such as spark plugs, air filters,

adjustments, fuel system cleaning and obstruction due

to buildup is not covered by this warranty.

Other Exclusions

This warranty excludes:

– Cosmetic defects such as paint, decals, etc.

– Wear items such as filter elements, o-rings, etc.

– Accessory parts such as starting batteries, and

storage covers.

– Failures due to acts of God and other force majeure

events beyond the manufacturer’s control.

– Problems caused by parts that are not original

Champion Power Equipment parts.

This warranty does not apply to generators used for

prime power in place of a utility.

Limits of Implied Warranty and Consequential Damage

Champion Power Equipment disclaims any obligation to

cover any loss of time, use of this product, freight, or

any incidental or consequential claim by anyone from

using this generator. THIS WARRANTY IS IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE.

A unit provided as an exchange will be subject to the

warranty of the original unit. The length of the warranty

governing the exchanged unit will remain calculated by

reference to the purchase date of the original unit.

This warranty gives you certain legal rights which may

change from province to province. Your province may

also have other rights you may be entitled to that are not

listed within this warranty.

Contact Information

Address

Champion Power Equipment, Inc.

Customer Service

12039 Smith Ave.

Santa Fe Springs, CA 90670 USA

www.championpowerequipment.com

Customer Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)

Toll Free : 1-877-338-0999

info@championpowerequipment.com

Fax no.: 1-562-236-9429

Technical Service

Mon – Fri 8:30 AM – 5:00 PM (PST/PDT)

Toll Free : 1-877-338-0999

tech@championpowerequipment.com

24/7 Tech Support: 1-562-204-1188

WARRANTY

Champion Power Equipment, Inc (CPE),

Emission Control System Warranty

Your Champion Power Equipment (CPE) engine complies with Environment Canada (EC) emission

regulations.

YOUR WARRANTY RIGHTS AND OBLIGATIONS:

CPE is pleased to explain the Emission Control Systems Warranty on your 2015 small off-road engine.

New engines must be designed, built and equipped, at the time of sale, to meet EC regulations for small

non-road engines. CPE must warrant the emission control system on your small off-road engine for the

period of time listed below, provided there has been no abuse, neglect, unapproved modification, or

improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor, fuel-injection system, the ignition

system, catalytic converter and fuel lines. Also included may be hoses, belts, connectors and other

emission related assemblies. Where a warrantable condition exits, CPE will repair your small off-road

engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S EMISSION CONTROL SYSTEM WARRANTY COVERAGE:

This emission control system is warranted for two years, subject to provisions set forth below. If, during

the warranty period, emission related part on your engine is defective in materials or workmanship, the

part will be repaired or replaced by CPE.

OWNER WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for the performance of the required maintenance

listed in your Owner’s Manual. CPE recommends that you retain all your receipts covering maintenance

on your small off-road engine, but CPE cannot deny warranty solely for the lack of receipts or for your

failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that CPE may deny you

warranty coverage if your small, off-road engine or a part has failed due to abuse, neglect,

improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to an Authorized CPE service outlet, CPE

dealer or CPE, Santa Fe Springs, CA., USA as soon as a problem exists. The warranty repairs should be

completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact:

Champion Power Equipment, Inc.

Customer Service

12039 Smith Ave.

Santa Fe Springs, CA 90670

USA

Tel: 1-877-338-0999

tech@championpowerequipment.com

EMISSION CONTROL SYSTEM WARRANTY

The following are specific provisions relative to your Emission Control System Warranty

Coverage.

Emission Control System Warranty (ECS Warranty):

1. APPLICABILITY: The ECS Warranty Period shall begin on the date the new engine or equipment is

delivered to its original, end-use purchaser, and shall continue for 24 consecutive months thereafter.

2. GENERAL EMISSIONS WARRANTY COVERAGE

CPE warrants to the original, end-use purchaser of the new engine or equipment and to each subsequent

purchaser that each of its small off-road engines is:

a. Designed, built and equipped so as to conform at the time of sale with applicable regulations

under the Canadian Environmental Protection Act, 1999 (CEPA 1999).

b. Free from defects in materials and workmanship that cause the failure of a warranted part to be

identical in all material respects to the part as described in the engine manufacturer’s application for

certification for a period of two years.

3. THE WARRANTY ON EMISSION-RELATED PARTS WILL BE INTERPRETED AS

FOLLOWS:

a. Any warranted part that is not scheduled for replacement as required maintenance in the

Owners Manual shall be warranted for the ECS Warranty Period. If any such part fails during the ECS

Warranty Period, it shall be repaired or replaced by CPE according to Subsection “d” below. Any such

part repaired or replaced under the ECS Warranty shall be warranted for any remainder of the ECS

Warranty Period.

b. Any warranted, emissions-related part which is scheduled only for regular inspection as

specified in the Owners Manual shall be warranted for the ECS Warranty Period. A statement in such

written instructions to the effect of “repair or replace as necessary”, shall not reduce the ECS Warranty

Period. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder

of the ECS Warranty Period.

c. Any warranted, emissions-related part which is scheduled for replacement as required

maintenance in the Owner’s Manual shall be warranted for the period of time prior to the first scheduled

replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be

repaired or replaced by CPE according to Subsection “d” below. Any such emissions-related part repaired

or replaced under the ECS Warranty, shall be warranted for the remainder of the ECS Warranty Period

prior to the first scheduled replacement point for such emissions-related part.

d. Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall

be performed at no charge to the owner at a CPE Authorized Service Outlet.

e. The owner shall not be charged for diagnostic labor which leads to the determination that a

part covered by the ECS Warranty is in fact defective, provided that such diagnostic work is performed at

a CPE Authorized Service Outlet.

f. CPE shall be liable for damages to other original engine components or approved modifications

proximately caused by a failure under warranty of an emission-related part covered by the ECS Warranty.

g. Throughout the ECS Warranty Period, CPE shall maintain a supply of warranted emission-

related parts sufficient to meet the expected demand for such emission-related parts.

h. Any CPE Authorized and approved emission-related replacement part may be used in the

performance of any ECS Warranty maintenance or repair and will be provided without charge to the

owner. Such use shall not reduce CPE’s warranty obligation.

i. Unapproved add-on or modified parts may not be used to modify or repair a CPE engine. Such

use voids this ECS Warranty and shall be sufficient grounds for disallowing an ECS Warranty claim. CPE

shall not be liable hereunder for failures of any warranted parts of a

CPE engine caused by the use of such an unapproved add-on or modified part.

EMISSION-RELATED PARTS INCLUDE THE FOLLOWING: (using those portions of the list

applicable to the engine)

Systems covered by this warranty

Parts Description

Fuel Metering System

Fuel regulator, Carburetor and internal parts

Air Induction System

Air cleaner, Intake manifold

Ignition System

Spark plug and parts, Magneto ignition system

Exhaust System

Exhaust manifold, catalytic converter

Miscellaneous Parts

Tubing, Fittings, Seals, Gaskets, and Clamps

associated with these listed systems.

Evaporative Emissions

Fuel Tank, Fuel Cap, Fuel Line, Fuel Line Fittings,

Clamps, Pressure Relief Valves, Control Valves,

Control Solenoids, Electronic Controls, Vacuum

Control Diaphragms, Control Cables, Control

Linkages, Purge Valves, Vapor Hoses, Liquid/Vapor

Separator, Carbon Canister, Canister Mounting

Brackets, Carburetor Purge Port Connector

TO OBTAIN WARRANTY SERVICE:

You must take your CPE engine or the product on which it is installed, along with your warranty

registration card or other proof of original purchase date, at your expense, to any Champion Power

Equipment dealer who is authorized by Champion Power Equipment, Inc. to sell and service that CPE

product during his normal business hours. Claims for repair or adjustment found to be caused solely by

defects in material or workmanship will not be denied because the engine was not properly maintained

and used.

If you have any questions regarding your warranty rights and responsibilities, or to obtain

warranty service, please write or call Customer Service at Champion Power Equipment, Inc.

Champion Power Equipment, Inc.

12039 Smith Ave.

Santa Fe Springs, CA 90670

USA

1-877-338-0999

Attn: Customer Service

tech@championpowerequipment.com