Chengdu Ebyte Electronic Technology E01 Wireless transceiver module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3873277
Application ID	1PwRcx+VzBOJ8s/HiuzYkA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.43kB (230333 bits)
Date Submitted	2018-06-02 00:00:00
Date Available	2018-06-02 00:00:00
Creation Date	2018-05-22 14:40:23
Producing Software	Microsoft® Office Word 2007
Document Lastmod	2018-05-31 15:46:54
Document Title	User manual
Document Creator	Microsoft® Office Word 2007
Document Author:	elaine CHEN

E01-ML01DP5 Datasheet V1.0
Website： www.cdebyte.com/en
--1. Introduction
E01
E01
is
the
iconic
product
of
EBYTE.
This
nRF24L01+PA+LNA RF module operates at 2.4 GHz, with
SPI interface and stable production, which make the
module suitable for various applications.
E01 is based on original imported nRF24L01P form
Nordic in Norway. And equipped with 20dBm power
amplifier chip imported from USA, which makes the
transmitting power achieves 100mW (20dBm) while the
receiving sensitivity enhanced by 10dB. Those features
make the transmitting distance 10 times longer than nRF24L01P itself. The anti-interference shielding cover on the
module makes the anti-interference performance better.
--2. Electrical parameter
E01
No.
Parameter item
Parameter details
Description
RF IC
nRF24L01P
Size
18 * 33.4 mm
Weight
4.9g
Average weight
PCB
SMT
Lead-free
Connector
2 * 4 * 2.54 mm
Supply voltage
2.0 ~ 3.6V DC
Frequency
2400 ~ 2525MHz
Communication level
0.7VCC ~ 3.6V
Operation Range
2000m
Nordic
Plug-in
Notes: the voltage higher than 3.6V is forbidden
Adjustable
VCC refers to the supply voltage
Test condition: Clear and open area, 20dBm，
antenna gain: 2dBi，height: 2m，Air date rate:
250Kbps
10
Transmitting Power
Maximum 20dBm
100mW
11
Air data rate
250kbps~2Mbps
250kbps, 1Mbps, 2Mbps
12
Sleep current
1.0uA
13
Transmitting current
130mA@20dBm
14
Receiving current
21mA
15
Communication interface
SPI
16
Transmitting length
3 level FIFO.
32 bytes (maximum) for one package
17
Receiving length
3 level FIFO.
32 bytes (maximum) for one package
18
Antenna type
SMA-K
19
Sensitivity
-106dBm@250kbps
20
Operating temperature
-40 ~ +85℃
Relative humidity, no condensation
21
Operating humidity
10% ~ 90%
22
Storage temperature
-40 ~ +125℃
--3.
Pin definition
Page 4 of
nRF24L01P sets as power-down, CE low level
≥300mA
CE=1
Data rate: up to 10Mbps
50 ohm characteristic impedance
Please see more in IC datasheet
E01
Technical support: support@cdebyte.com
E01-ML01DP5 Datasheet V1.0
Website： www.cdebyte.com/en
Pin No.
Pin item
Pin direction
Pin application
GND
Ground
VCC
Power supply 2.0V ~ 3.6V DC
CE
Input
Chip Enable
CSN
Input
SPI Chip select
SCK
Input
SPI clock
MOSI
Input
SPI master output slave input
MISO
Output
SPI master input slave output
IRQ
Output
Interrupt request.
--4. Note
No.
Item
Static
electricity
Welding
Power
E01
supply
Ground
Attention
Please try not to touch the electronic components with bare hands.
When welding, soldering iron needs grounding. The producer needs to wear cable
electrostatic bracelet which is grounding when mass production.
Power quality has a great impact on the performance of the module, please make sure
the power supply has small ripple and avoid the frequent and large jitter. π filter is
recommended(Ceramic capacitor / / tantalum capacitor + inductance).
Single-point grounding is recommended. 0 ohm resistor or 10mH inductance are
recommended.
How to install antenna has a great impact on the performance of the module, please
make sure the antenna is exposed and vertical upward. It will lead to the transmitting
Antenna
distance greatly weakened if the antenna installs in the interior of housing. When the
module is installed in the interior of the housing, high-quality antenna extension line
can be used to extend the antenna to the outside of the housing.
If there are different modules work in other frequency band in the same product, the
Interference
user need to plan rationally and take measures to shield, in case the harmonic
interference and intermodulation interference exist.
Page 4 of
Technical support: support@cdebyte.com
E01-ML01DP5 Datasheet V1.0
Website： www.cdebyte.com/en
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
If the FCC identification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display a
label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: 2ALPH-E01 Or Contains FCC ID:
2ALPH-E01”
When the module is installed inside another device, the user manual of the host must
contain below warning statements;
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
The devices must be installed and used in strict accordance with the manufacturer's instructions
as described in the user documentation that comes with the product.
Page 4 of
Technical support: support@cdebyte.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Has XFA                         : No
Language                        : zh-CN
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : elaine CHEN
Create Date                     : 2018:05:22 14:40:23+08:00
Creator Tool                    : Microsoft® Office Word 2007
Modify Date                     : 2018:05:31 15:46:54+08:00
Metadata Date                   : 2018:05:31 15:46:54+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:27ebcc8a-a9b0-4132-ad43-35ef6fb7218f
Instance ID                     : uuid:ce9672d2-172a-4786-851b-bf1629529de0
Page Count                      : 3
Author                          : elaine CHEN

EXIF Metadata provided by EXIF.tools