Chiayo Electronics Co DCT-511 2.4G Digital Two-Way Tour Guide System User Manual

Chiayo Electronics Co Ltd 2.4G Digital Two-Way Tour Guide System

User Manual

DCT-511 DCR-511 2.4G DIGITAL TWO-WAY TOUR GUIDE SYSTEM ISO 9001:2008 ISO 14001 OHSAS 18001 Green Product OPERATION MANUAL ISO14 0 01REG ISTER E DO H S A S18 0 01REG ISTER E D
-1- DCT-511 Mini transmitter Parts and functions 1. Antenna 2. Mute 3. Volume control 4. Power/frequency synchronizing 5. MIC-MIX-AUX IN mode switch 6. Aux input (Ø 3.5mm) 7. Power indicator 8. Mute indicator 9. Earphone jack (Ø 3.5mm) 10. Mini USB charging port 11. Reset Instructions 1. Mute: Press to activate or cancel muting. 2. Aux input: You may play music files in your device as background music by connecting to the transmitter. In a museum, you may also play respective introductions recorded for different galleries. 3. Audio mode switch: If using only earphone, please switch to . For only music play, please switch to . To simultaneously use earphone and play music, please switch to middle. 4. Power and charging: Press the power button one second to turn on the transmitter and the indicator will light green. It turns red when battery low or during charging. It lights off once the battery is full. The charging process takes approximately four hours. 1234567 8 91011
ISO 9001 / ISO 14001 / OHSAS 18001 -2- DCR-511 Mini receiver Parts and functions 1. Antenna 2. Press to talk 3. Volume control 4. Power/frequency synchronizing 5. Power indicator 6. Reception indicator 7. Earphone jack (Ø 3.5mm) 8. Mini USB charging port 9. Reset Instructions 1. Talking: Press the talk button to talk with your guide and the conversation could be heard by other members. And release to stop. 2. Reception indicator: The LED stays green within the reception from the tour guide. Once beyond the reception range, it will flash red and beep as a warning of dropout. 3. Power and charging: Press the power button one second to turn on the transmitter and the indicator will light green. It turns red when battery low or during charging. It lights off once the battery is full. The charging process takes approximately four hours. 12345 6 789
-3- Frequency synchronizing between DCT-511 and DCR-511 1. Before the synchronizing, please power off the device. 2. Press DCT-511’s power button for five seconds till the mute indicator flashes green, which implies readiness to synchronize. 3. Press DCR-511’s power button for five seconds till the reception indicator flashes green, which implies readiness to synchronize. Both mute and reception indicators will light green after the setting is completed. 4. DCT-511’s mute indicator will stop flashing after a setting period of about twelve seconds. 5. DCR-511’s reception indicator will stop flashing after a setting period of about twelve seconds. 6. To synchronize mass receivers with the transmitter, just to follow STEP 2 on all receivers simultaneously. 7. If the power indicator glows red, it means battery low and needs to be recharged. The system paring can be made only after the charging process is finished.
ISO 9001 / ISO 14001 / OHSAS 18001 -4- Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Navigation menu