Chiayo Electronics Co SQ-6100IRDA Wireless Mircophone User Manual

Chiayo Electronics Co Ltd Wireless Mircophone Users Manual

Users Manual

SDR-6200 IrDA SDR-6100 IrDA UHF 2-Way Synchronizing True Diversity / Diversity Wireless Microphone System ISO 9001 ISO 14001 OHSAS 18001 GREEN PRODUCT Operation manual IS O140 01RE GIS TER EDO H S A S180 01RE GIS TER ED
-1- Thank you for choosing this wireless microphone system! Our products are designed to last and for user friendly operation. Each system consists of: 1. a receiver 2. a handheld or belt-pack transmitter 3. a pair of antennas 4. a switching adaptor 5. an operation manual For more details, please take a few moments to read this operating manual to have a thorough understanding of the function and operation of both transmitter and receiver. Parts and functions of SDR-6200 IrDA/SDR-6100 IrDA receiver Front panel 1. Power switch 2. IR sensor area 3. Diversity indicator 4. Audio signal indicator 5. LCD display 6. UP button 7. DOWN button 8. IrDA synchronization button 9. SET button Rear panel SDR-6200 IrDA SDR-6100 IrDA 10. Antenna B socket (TNC) 11. Balanced audio output 12. Unbalanced audio output 13. Antenna A socket (TNC) 14. DC in POWERD IV E R S IT YA BA U D IO SDR-6100 IrDA UHF 2-WAY SYNC. DIVERSITYRECEIVER123 45678910 11 12 1314LINE OUTUNBALANCEDBALANCEDDC INDC IN12V12VANT.AANT.B1.GND2.3.MIC O U T101112 13 14
ISO 9001｜ISO 14001｜OHSAS 18001 -2- Changing CHANNEL / FREQUENCY First, press "SET" till the display shows . Then press UP or DOWN to select a new channel. As the channel changes, the frequency changes accordingly, too. After the setting is made, the data will be automatically saved. CHANNEL scanning For an interference- free operation, a cleaner channel might be necessary if the current one receives too much interference. Before scanning, the transmitter must be switched off. First, press "SET" till the display shows . Then press UP or DOWN to go to the next clean channel. After the setting is made, the data will be automatically saved. CHANNEL SYNCHRONIZING of the receiver and transmitter a. Limit the distance between the receiver and transmitter within 30cm. b. Align both infrared areas c. To change the receiver’s channel, please press the synchronizing button of the transmitter. The transmitter's LED will grow to imply synchronizing signal transmitted and will appear on the receiver's LCD, which means the receiver has been successfully synchronized. d. To change the transmitters channel, please press the SYNC button of the receiver and will appear on the receiver’s display, followed by indicating data transferred.
-3- Adjusting VOLUME level The setting can be made right on the main menu . Press UP or DOWN to choose a new level. After the setting is made, the data will be automatically saved. Adjusting SQUELCH level First, press "SET" till the display shows . Then press UP or DOWN to choose a new level. After the setting is made, the data will be automatically saved. Receiver installation For best operation, the receiver should be at least 1m above the ground and 1m away from a wall or metal surface to minimize reflections. The transmitter should also be at least 1m away from a wall or metal surface to minimize reflections. The transmitter should also be at least 1m away from the receiver. Keep antennas away from noise source such as motors, automobiles, neon light as well as large metal objects. Audio output connection There are two audio outputs on the back of the receiver, Mic-level balanced and Line-level unbalanced. Use shielded audio cable for the connection between the receiver and the amplifier/mixer. If the amplifier/mixer has a 1/4"(6.3mm) phone jack, connect a cable from the 1/4"(6.3mm) unbalanced audio output from the receiver to the amplifier/mixer. If the amplifier/mixer has an XLR input, connect a cable from the balanced XLR audio output from the receiver to the amplifier/mixer input. Rack mounting The receiver can be cabinet-mounted by either one or two units. If only one receiver is to be mounted, an optional kit is available and it's installed as shown in Fig 1. If two receivers are to be mounted, they can be assembled by another kit and installed as shown in Fig 2. (Fig 1) (Fig 2)
ISO 9001｜ISO 14001｜OHSAS 18001 -4- UHF handheld transmitters（SQ-6100 IrDA(R)｜SQ-6100 IrDA｜SQ-2100 IrDA｜SQ-1100 IrDA） →SQ-6100 IrDA(R)｜SQ-6100 IrDA →SQ-2100 IrDA →SQ-1100 IrDA Parts and functions SQ-6100 IrDA(R) SQ-6100 IrDA SQ-2100 IrDA SQ-1100 IrDA Cartridge 1 1 1 1 Battery power LED 2 2 2 2 Power switch 3 3 3 3 LCD 4 4 - - Menu button 5 5 - - Setting button 6 6 - - IrDA synchronizing button 7 7 4 4 Battery compartment 8 8 5 5 Color cap 9 9 6 - IrDA sensor area 10 10 7 6 Charging port 11 - - 7 Battery installation & indicator This transmitter requires 2 x AA batteries to operate. To install, remove the battery cover and slide the batteries into the battery compartment & replace the battery cover. Note: Batteries contain a corrosive acid that may leak and damage the transmitter when stored for a long period. Batteries should be removed from the transmitter before storing without use for more than 4 weeks. When the transmitter is switched ON, a red LED  will blink once to indicate the batteries installed are in good condition. If the LED remains illuminated, it means the batteries are weak and require replacement. 1 2 3 74 56
-5- Channel synchronizing of the receiver and transmitter 1. To achieve a trouble-free synchronization, please limit the distance between the receiver and transmitter to within 30cm. 2. Align both sensor areas 3. To change the receiver’s channel, please press the synchronizing button of the transmitter. The transmitter will transmit synchronizing signal to the receiver and change its channel. 4. To change the transmitter’s channel, please press the synchronizing button of the receiver. The receiver will transmit synchronizing signal to the transmitter and change its channel. Other settings（SQ-6100 IrDA(R)｜SQ-6100 IrDA） 1. Channel setting Use MENU button to go to the CHANNEL｜FREQUENCY page.︰ After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made. Pressing SET / MENU buttons will increase / decrease the channel number. The corresponding frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically saved. 2. Battery type setting Use MENU button to go to the BATTERY TYPE page.︰ After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made. Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3 seconds after selecting a battery type, it will be automatically saved. Remark: NiMH battery must be selected when rechargeable battery is being used. Never select AKLN (alkaline) when transmitter is intended for charging as alkaline battery isn’t rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong and misleading status information.
ISO 9001｜ISO 14001｜OHSAS 18001 -6- UHF belt-pack transmitters（SM-7100 IrDA｜SM-6100 IrDA｜SM-2100 IrDA｜SM-1100 IrDA） SM-7100 IrDA｜SM-6100 IrDA｜SM-2100 IrDA SM-1100 IrDA Parts and functions SM-7100 IrDA SM-6100 IrDA SM-2100 IrDA SM-1100 IrDA Antenna 1 1 1 1 LCD 2 2 - - Cover release button 3 3 3 6 Power switch 4 11 11 3 IrDA synchronizing button 5 5 5 7 Menu button 6 6 6 - Setting button 7 7 7 - High-impedance gain control (GT) 8 8 8 8 Low-impedance gain control (MT) 9 9 9 9 Battery compartment 10 10 10 10 Audio mute switch 11 - - - Battery power LED 12 12 12 2 IrDA sensor area 13 13 13 4 Mini XLR connector 14 14 14 5 Charging contacts 15 15 15 11 Battery installation & indicator This belt-pack requires 2 x AA batteries to operate. To install, open the battery cover using the cover release buttons and insert the batteries into the battery compartment. 123 39784 561011 12131415123456781011 119
-7- Note: Batteries contain a corrosive acid that may leak and damage the belt-pack when stored for a long period. Batteries should be removed from the belt-pack before storing without use for more than 4 weeks. When the transmitter is switched ON, the battery power LED (red) will blink once to indicate the batteries installed are in good condition. If the LED remains illuminated the batteries have expired and require replacement. Channel synchronizing of the receiver and transmitter 1. To achieve a trouble-free synchronization, please limit the distance between the receiver and transmitter to within 30cm. 2. Align both sensor areas 3. To change the receiver’s channel, please press the synchronizing button of the transmitter. The transmitter will transmit synchronizing signal to the receiver and change its channel. 4. To change the transmitter’s channel, please press the synchronizing button of the receiver. The receiver will transmit synchronizing signal to the transmitter and change its channel. GAIN setting (GT｜MT) Gain control enables the user to set different output levels. GT is for the use of instrument with high impedance, such as guitar while MT is for the use of low impedance such as lapel or headset microphones. Other settings（SM-7100 IrDA｜SM-6100 IrDA） 1. Channel setting Use MENU button to go to the CHANNEL｜FREQUENCY page.︰ After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made. Pressing SET / MENU buttons will increase / decrease the channel number. The corresponding frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically saved. 2. Battery type setting Use MENU button to go to the BATTERY TYPE page.︰ After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made. Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3 seconds after selecting a battery type, it will be automatically saved. Remark: NiMH battery must be selected when rechargeable battery is being used. Never select AKLN (alkaline) when transmitter is intended for charging as alkaline battery isn’t rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong and misleading status information.
ISO 9001｜ISO 14001｜OHSAS 18001 -8-
-9-
ISO 9001｜ISO 14001｜OHSAS 18001 -10-
FCC Caution To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This device complies with Part 74 & 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. CHIAYO ELECTRONICS CO.,LTD. Http://www.chiayo.com.tw｜Email: sales@chiayo.com.tw Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan｜Tel: 886-2-27415741｜Fax: 886-2-27525242 Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan｜Tel: 886-5-2711000｜Fax: 886-5-5767611 12I1311

Navigation menu