Chic Technology RMB214UP WIRELESS MOUSE User Manual PMU MRF00001 A1

Chic Technology Corporation WIRELESS MOUSE PMU MRF00001 A1

users manual

Wireless Mouse User's GuideNotice:Federal Communications Commission (FCC) requirements, Part 15This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment.Congratulations on your purchase of this Wireless Mouse. Please carefully read the User's Guide to learn about the installation and the powerful functions of your new Wireless Mouse.1. Contents of the Package 1) Wireless Mouse (one channel or two channel) * 1 2) Receiver *1 (PS/2, USB or UP Combo) 3) Two AA or AAA Batteries for the Mouse 4) Mouse Driver * 1 (Disk or CD-ROM) 5) User's Guide * 12. Install Hardware 2-1. Install the Receiver with a PS/2 Connector 1) Please turn off the PC. 2) Plug the PS/2 connector of the receiver into the PS/2 mouse port of the PC. 2-2. Install the Receiver with a USB Connector 1) You can turn on the PC before connect the USB connector with PC. 2) Plug the USB connector of the receiver into the USB port of the PC. 2-3. Install the Receiver with a USB to PS/2 Combo Connector 1) The combo connector is a USB connector with a USB to PS/2 adaptor. 2) Please check the mouse port of your PC. If the mouse port of the PC is USB, please plug the USB connector to the PC without using the USB to PS/2 adaptor. 3) If the mouse port of the PC is PS/2, please turn off the PC. Connect the USB connector with the USB to PS/2 adaptor, and then connect the receiver with the PC. 2-4. Select the Channel Please skip this section if the mouse has only one channel. The location of the channel switch may be different due to various mouse shapes.--------------------------------------------------------------------------------------------------------------------------------------------------------Essential requirements - Article 3 Protection requirements for health and safety - Article 3.1a --Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility -Article 3.1b --Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-17 and EN 55024 has been conducted. These are considered relevant and sufficient. Effective use of the radio spectrum -Article 3.2--Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered relevant and sufficient. 1) The two-channel switch is located at the back of the mouse or inside the battery case. Select Channel "1" or "2" . 2) Put the batteries into the battery case. Note: There is a channel selector at the back of the receiver for some models. If the receiver has the channel selector, please select the channel as same as the channel of the mouse. 2-5. Link the Mouse with the Receiver 1) Turn on the PC. The LED indicator on the receiver will light. 2) Press the ID Link Button on the receiver and the LED indicator will blink. The receiver is ready to automatically link with the mouse 3) Press the ID Link Button on the back of the mouse and the LED indicator on the receiver will blink quickly. The indicator will stay in light while successfully finish the linkage. 4) The LED indicator will blink while you move the mouse. 5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the above linkage instructions. 6) If the selected channel is interfered by other wireless-mouse users nearby, please change the Link ID by re-linkage or select the other channel immediately.3.Install Driver 3-1. Notice 1) The driver supports Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME and Windows XP. 2) The USB interface is compatible with Windows 98, Windows 2000, Windows ME and Windows XP only. 3-2. Installation 1) Insert the driver disk or CD-ROM to your PC. The PC system may automatically install the driver through selecting the PC auto-install function. 2) If the PC system does not set the auto-install function, please double click the file "Setup.exe" and follow the setup instructions to complete the driver installation. 3) A Mouse Setting icon will appear on the tool bar of Windows after you successfully finish the installation. 3-3. Select Mouse Functions 1) Double click the Mouse Setting icon. 2) Follow the instructions of the selection items to set the button functions.4. Batteries Notice1) The LED indicator or the scroll wheel on the mouse will light while the mouse is low battery. Please change the batteries immediately.2) Move the mouse while the mouse is in the sleeping mode.Wireless Mouse User's GuideNotice:Federal Communications Commission (FCC) requirements, Part 15This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to operate the equipment.Congratulations on your purchase of this Wireless Mouse. Please carefully read the User's Guide to learn about the installation and the powerful functions of your new Wireless Mouse.1. Contents of the Package 1) Wireless Mouse (one channel or two channel) * 1 2) Receiver *1 (PS/2, USB or UP Combo) 3) Two AA or AAA Batteries for the Mouse 4) Mouse Driver * 1 (Disk or CD-ROM) 5) User's Guide * 12. Install Hardware 2-1. Install the Receiver with a PS/2 Connector 1) Please turn off the PC. 2) Plug the PS/2 connector of the receiver into the PS/2 mouse port of the PC. 2-2. Install the Receiver with a USB Connector 1) You can turn on the PC before connect the USB connector with PC. 2) Plug the USB connector of the receiver into the USB port of the PC. 2-3. Install the Receiver with a USB to PS/2 Combo Connector 1) The combo connector is a USB connector with a USB to PS/2 adaptor. 2) Please check the mouse port of your PC. If the mouse port of the PC is USB, please plug the USB connector to the PC without using the USB to PS/2 adaptor. 3) If the mouse port of the PC is PS/2, please turn off the PC. Connect the USB connector with the USB to PS/2 adaptor, and then connect the receiver with the PC. 2-4. Select the Channel Please skip this section if the mouse has only one channel. The location of the channel switch may be different due to various mouse shapes.--------------------------------------------------------------------------------------------------------------------------------------------------------Essential requirements - Article 3 Protection requirements for health and safety - Article 3.1a --Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient. Protection requirements for electromagnetic compatibility -Article 3.1b --Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-17 and EN 55024 has been conducted. These are considered relevant and sufficient. Effective use of the radio spectrum -Article 3.2--Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered relevant and sufficient. 1) The two-channel switch is located at the back of the mouse or inside the battery case. Select Channel "1" or "2" . 2) Put the batteries into the battery case. Note: There is a channel selector at the back of the receiver for some models. If the receiver has the channel selector, please select the channel as same as the channel of the mouse. 2-5. Link the Mouse with the Receiver 1) Turn on the PC. The LED indicator on the receiver will light. 2) Press the ID Link Button on the receiver and the LED indicator will blink. The receiver is ready to automatically link with the mouse 3) Press the ID Link Button on the back of the mouse and the LED indicator on the receiver will blink quickly. The indicator will stay in light while successfully finish the linkage. 4) The LED indicator will blink while you move the mouse. 5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the above linkage instructions. 6) If the selected channel is interfered by other wireless-mouse users nearby, please change the Link ID by re-linkage or select the other channel immediately.3.Install Driver 3-1. Notice 1) The driver supports Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME and Windows XP. 2) The USB interface is compatible with Windows 98, Windows 2000, Windows ME and Windows XP only. 3-2. Installation 1) Insert the driver disk or CD-ROM to your PC. The PC system may automatically install the driver through selecting the PC auto-install function. 2) If the PC system does not set the auto-install function, please double click the file "Setup.exe" and follow the setup instructions to complete the driver installation. 3) A Mouse Setting icon will appear on the tool bar of Windows after you successfully finish the installation. 3-3. Select Mouse Functions 1) Double click the Mouse Setting icon. 2) Follow the instructions of the selection items to set the button functions.4. Batteries Notice1) The LED indicator or the scroll wheel on the mouse will light while the mouse is low battery. Please change the batteries immediately.2) Move the mouse while the mouse is in the sleeping mode.F1~F10Auto ScrollBackspaceClose ApplicationConnect to InternetControl LockControl PanelCopyCutDeleteDouble ClickDownDrag LockEndEnterEscExplorerFind ComputerFind FileHomeHorizontal WheelInterent Explorer BackwardInterent Explorer ForwardLanuch Default BrowserLanuch Default E-mailLeftMaximize WindowsMiddle ButtonMinimize All WindowsMinimize WindowsPage DownPage UpPasteRedoRightRun...Shift LockSpaceStart Menu System HelpSystem Property Tab Undo Undo Minimize All Windows Universal Scroll Universal Zoom UpFigure 3-3-1 Figure 3-3-23Figure 2-1 3Figure 2-23Figure 2-3
Wireless Mouse User's GuidePMU-MRF00001_A1

Navigation menu