Chic Technology RMB287UP Wireless Ball Mouse User Manual PMU MRF00040
Chic Technology Corporation Wireless Ball Mouse PMU MRF00040
USERS MANUAL
Wireless Mouse
User's Guide
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Congratulations on your purchase of this Wireless Mouse. Please carefully read the
User's Guide to learn about the installation and the powerful functions of your new
Wireless Mouse.
1. Contents of the Package
1) Wireless Mouse (one channel or two channel) * 1
2) Receiver *1 (PS/2, USB or UP Combo)
3) Two AA or AAA Batteries for the Mouse
4) Mouse Driver * 1 (Optional )
5) User's Guide * 1
2. Install Hardware
2-1. Install the Receiver with a PS/2 Connector
1) Please turn off the PC.
2) Plug the PS/2 connector of the receiver into the PS/2 mouse port of the PC.
2-2. Install the Receiver with a USB Connector
1) You can turn on the PC before connect the USB connector with PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2-3. Install the Receiver with a USB to PS/2 Combo Connector
1) The combo connector is a USB connector with a USB to PS/2 adaptor.
2) Please check the mouse port of your PC. If the mouse port of the PC is USB, please plug the USB
connector to the PC without using the USB to PS/2 adaptor.
3) If the mouse port of the PC is PS/2, please turn off the PC. Connect the USB connector with the
USB to PS/2 adaptor, and then connect the receiver with the PC.
--------------------------------------------------------------------------------------------------------------------------------------------------------
CE Declaration Of Conformity
Hereby, the manufacturer, declares that this Wireless Mouse is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Essential requirements - Article 3
Protection requirements for health and safety - Article 3.1a
--Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility -Article 3.1b
--Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-03 has been conducted. These are
considered relevant and sufficient.
Effective use of the radio spectrum -Article 3.2
--Testing for radio test suites according to EN 300 220-3 has been conducted. These are considered relevant and sufficient.
Caution: May explode or leak if recharged, inserted improperly, disposed of in fire or mixed with used or different battery types.
2-4. Select the Channel
Please skip this section if the mouse has only one channel. The location of the channel
switch may be different due to various mouse shapes.
1) The two-channel switch is located at the back of the mouse or inside the battery case. Select
Channel "1" or "2" .
2) Put the batteries into the battery case.
Note: There is a channel selector at the back of the receiver for some models. If the
receiver has the channel selector, please select the channel as same as the
channel of the mouse.
2-5. Link the Mouse with the Receiver
1) Turn on the PC. The LED indicator on the receiver will light.
2) Press the ID Link Button on the receiver and the LED indicator will blink. The receiver is
ready to automatically link with the mouse
3) Press the ID Link Button on the back of the mouse and the LED indicator on the receiver
will blink quickly. The indicator will stay in light while successfully finish the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the
above linkage instructions.
6) If the selected channel is interfered by other wireless-mouse users nearby, please change
the Link ID by re-linkage or select the other channel immediately.
3.Install Driver
3-1. Notice
1) The driver supports Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME
and Windows XP.
2) The USB interface is compatible with Windows 98, Windows 2000, Windows ME and
Windows XP only.
3-2. Installation
1) Insert the driver disk or CD-ROM to your PC. The PC
system may automatically install the driver through
selecting the PC auto-install function.
2) If the PC system does not set the auto-install function,
please double click the file "Setup.exe" and follow the
setup instructions to complete the driver installation.
3) A Mouse Setting icon will appear on the tool bar of
Windows after you successfully finish the installation.
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions of the selection items to set the
button functions.
4. Batteries Notice
1) The LED indicator or the scroll wheel on the mouse will light while the mouse is low battery.
Please change the batteries immediately.
2) Move the mouse while the mouse is in the sleeping mode.
Wireless Mouse
User's Guide
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the users authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Congratulations on your purchase of this Wireless Mouse. Please carefully read the
User's Guide to learn about the installation and the powerful functions of your new
Wireless Mouse.
1. Contents of the Package
1) Wireless Mouse (one channel or two channel) * 1
2) Receiver *1 (PS/2, USB or UP Combo)
3) Two AA or AAA Batteries for the Mouse
4) Mouse Driver * 1 (Optional )
5) User's Guide * 1
2. Install Hardware
2-1. Install the Receiver with a PS/2 Connector
1) Please turn off the PC.
2) Plug the PS/2 connector of the receiver into the PS/2 mouse port of the PC.
2-2. Install the Receiver with a USB Connector
1) You can turn on the PC before connect the USB connector with PC.
2) Plug the USB connector of the receiver into the USB port of the PC.
2-3. Install the Receiver with a USB to PS/2 Combo Connector
1) The combo connector is a USB connector with a USB to PS/2 adaptor.
2) Please check the mouse port of your PC. If the mouse port of the PC is USB, please plug the USB
connector to the PC without using the USB to PS/2 adaptor.
3) If the mouse port of the PC is PS/2, please turn off the PC. Connect the USB connector with the
USB to PS/2 adaptor, and then connect the receiver with the PC.
--------------------------------------------------------------------------------------------------------------------------------------------------------
CE Declaration Of Conformity
Hereby, the manufacturer, declares that this Wireless Mouse is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Essential requirements - Article 3
Protection requirements for health and safety - Article 3.1a
--Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility -Article 3.1b
--Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-03 has been conducted. These are
considered relevant and sufficient.
Effective use of the radio spectrum -Article 3.2
--Testing for radio test suites according to EN 300 220-3 has been conducted. These are considered relevant and sufficient.
Caution: May explode or leak if recharged, inserted improperly, disposed of in fire or mixed with used or different battery types.
2-4. Select the Channel
Please skip this section if the mouse has only one channel. The location of the channel
switch may be different due to various mouse shapes.
1) The two-channel switch is located at the back of the mouse or inside the battery case. Select
Channel "1" or "2" .
2) Put the batteries into the battery case.
Note: There is a channel selector at the back of the receiver for some models. If the
receiver has the channel selector, please select the channel as same as the
channel of the mouse.
2-5. Link the Mouse with the Receiver
1) Turn on the PC. The LED indicator on the receiver will light.
2) Press the ID Link Button on the receiver and the LED indicator will blink. The receiver is
ready to automatically link with the mouse
3) Press the ID Link Button on the back of the mouse and the LED indicator on the receiver
will blink quickly. The indicator will stay in light while successfully finish the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the
above linkage instructions.
6) If the selected channel is interfered by other wireless-mouse users nearby, please change
the Link ID by re-linkage or select the other channel immediately.
3.Install Driver
3-1. Notice
1) The driver supports Windows 95, Windows 98, Windows NT, Windows 2000, Windows ME
and Windows XP.
2) The USB interface is compatible with Windows 98, Windows 2000, Windows ME and
Windows XP only.
3-2. Installation
1) Insert the driver disk or CD-ROM to your PC. The PC
system may automatically install the driver through
selecting the PC auto-install function.
2) If the PC system does not set the auto-install function,
please double click the file "Setup.exe" and follow the
setup instructions to complete the driver installation.
3) A Mouse Setting icon will appear on the tool bar of
Windows after you successfully finish the installation.
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions of the selection items to set the
button functions.
4. Batteries Notice
1) The LED indicator or the scroll wheel on the mouse will light while the mouse is low battery.
Please change the batteries immediately.
2) Move the mouse while the mouse is in the sleeping mode.
F1~F10
Auto Scroll
Backspace
Close Application
Connect to Internet
Control Lock
Control Panel
Copy
Cut
Delete
Double Click
Down
Drag Lock
End
Enter
Esc
Explorer
Find Computer
Find File
Home
Horizontal
Wheel
Interent Explorer
Backward
Interent Explorer
Forward
Lanuch Default
Browser
Lanuch Default
E-mail
Left
Maximize Windows
Middle Button
Minimize All
Windows
Minimize
Windows
Page Down
Page Up
Paste
Redo
Right
Run...
Shift Lock
Space
Start Menu
System Help
System Property
Tab
Undo
Undo Minimize
All Windows
Universal Scroll
Universal Zoom
Up
Figure 3-3-1
Figure 3-3-2
Wireless Mouse
User's Guide
PMU-MRF00040