Chic Technology RMO286UP WIRELESS OPTICAL MOUSE User Manual PMU MRF00041

Download:
Mirror Download [FCC.gov]
Document ID	468176
Application ID	hTHsmim+ddTCR8HZvDSCGw==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.98kB (249797 bits)
Date Submitted	2004-09-13 00:00:00
Date Available	2004-09-13 00:00:00
Creation Date	2004-07-07 13:29:35
Producing Software	Corel PDF Engine Version 9.397
Document Lastmod	2004-07-07 13:29:35
Document Title	PMU-MRF00041
Document Creator	CorelDRAW Version 9.397
Document Author:	Amanda_Kuo

Wireless Optical Mouse
User's Guide
2) Plug the USB connector of the receiver into the USB mouse port of PC.
Notice:
Federal Communications Commission (FCC) requirements, Part 15
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes of modifications not expressly approved by the grantee of this device could void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
-------------------------------------------------------------------------------------------------------------------------------------------------------CE Declaration Of Conformity
Hereby, the manufacturer, declares that this Wireless Optical Mouse is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Essential requirements - Article 3
Protection requirements for health and safety - Article 3.1a
--Testing for electric safety according to EN 60950 has been conducted. These are considered relevant and sufficient.
Protection requirements for electromagnetic compatibility -Article 3.1b
--Testing for electromagnetic compatibility according to EN 301 489-1 and EN 301 489-03 has been conducted. These are
considered relevant and sufficient.
Effective use of the radio spectrum -Article 3.2
--Testing for radio test suites according to EN 300 220-3 has been conducted. These are considered relevant and sufficient.
2-5. Link the Mouse with the Receiver
Congratulations on your purchase of this Wireless Optical Mouse. Please carefully read the
User's Guide to learn about the installation and the powerful functions of your new
Wireless Optical Mouse.
1. Contents of the Package
1) Turn on the PC. The LED indicator on the receiver will light.
2) Press the ID Link Button on the receiver and the LED indicator will blink. The receiver is ready to
automatically link with the mouse.
3) Press the ID Link Button on the back of the mouse and the LED indicator on the receiver will blink
quickly. The indicator will stay in light while successfully finish the linkage.
4) The LED indicator will blink while you move the mouse.
5) If you need to re-link the mouse or after changing the mouse batteries, please repeat the above
linkage instructions.
6) If the selected channel is interfered by other wireless-mouse users nearby, please change the Link
ID by re-linkage or select the other channel immediately.
3.Install Driver
3-1. Notice
1) The driver supports Windows 95, Windows 98, Windows NT,
Windows 2000, Windows ME and Windows XP.
2) The USB interface is compatible with Windows 98, Windows
2000, Windows ME and Windows XP only.
1) Wireless Optical Mouse (one channel or two channels)
2) Receiver (PS/2, USB or UP Combo)
3) Two AA or AAA Batteries for the Mouse
4) Mouse Driver Disk or CD-ROM
5) User's Guide
Optional Parts for Wireless Optical Mouse
(The optional parts may be different due to various wireless optical mice.)
1) AC to DC Adaptor
2) USB to DC Cable
Figure 2-1
Figure 2-2
2-1. Install the Receiver with PS/2 Connectors
1) Please turn off your PC.
2) Plug the PS/2 connector of the receiver into the PS/2 mouse port of the PC.
Figure 2-3
2-2. Install the Receiver with a USB Connector
1) You can turn on the PC before connect the USB connector with PC.
2-4. Select the Channel
Notice:
- Please skip this section if the mouse has only one channel.
- The location of the channel switch may be different due to various mouse shapes.
- There is a channel selector at the back of the receiver for some models. If so, please select the
channel as same as the channel of the mouse.
1) The two-channel switch is located at the back of the mouse or inside the battery case. Select Channel
"1" or "2".
2) Put the batteries into the battery box.
Caution: May explode or leak if recharged, inserted improperly, disposed of in fire or mixed with used or different battery types.
2. Install Hardware
- If you are running Windows 98 and plug the connector into the computer, you
may find a pop-up window that requires to insert the Windows 98 CD-ROM.
Please follow the window instruction to install the required driver or set the driver
path as "Windows\system" or the other path that the driver located.
2-3. Install the Receiver with a USB to PS/2 Combo Connector
1) The combo connector is a USB connector with a USB to PS/2 adaptor.
2) Please check the mouse port of your PC. If the mouse port of the PC is USB, please plug the USB
connector to the PC without using the USB to PS/2 adaptor.
3) If the mouse port of the PC is PS/2, please turn off the PC. Connect the USB connector with the
USB to PS/2 adaptor, and then connect the receiver with the PC.
3-2. Installation
1) Insert the driver disk or CD-ROM to your PC. The PC
system may automatically install the driver through selecting
the PC auto-install function.
2) If the PC system does not set the auto-install function, please
double click the file "Setup.exe" and follow the setup
instructions to complete the driver installation.
3) A Mouse Setting icon will appear on the taskbar of Windows
after you successfully finish the installation.
F1~F10
Auto Scroll
Backspace
Close Application
Connect to Internet
Control Lock
Control Panel
Copy
Cut
Delete
Double Click
Down
Drag Lock
End
Enter
Esc
Explorer
Find Computer
Find File
Home
Horizontal
Wheel
Interent Explorer
Backward
Interent Explorer
Forward
Lanuch Default
Browser
Lanuch Default
E-mail
Left
Maximize Windows
Middle Button
Minimize All
Windows
Minimize
Windows
Page Down
Page Up
Paste
Redo
Right
Run...
Shift Lock
Figure 3-3-1
Space
Start Menu
System Help
System Property
Tab
Undo
Undo Minimize
All Windows
Universal Scroll
Universal Zoom
Up
Figure 3-3-2
3-3. Select Mouse Functions
1) Double click the Mouse Setting icon.
2) Follow the instructions of the selection items to set the button functions.
4. Optional Charging Modes for Wireless Optical Mouse
Notice:
- There are three charge modes for the rechargeable version. Please skip this section if your
mouse is not rechargeable. Some mice may have only one or two charge modes.
- Please use rechargeable batteries for the chargeable mouse.
4-1. Power from PC
Connect the mouse to the USB port of PC with the USB to DC cable.
4-2. Power from Adaptor
Connect the mouse with the AC to DC adaptor.
4-3. Power from Cradle
The cradle must be connected with the required AC to DC adaptor in advance. Place the mouse on
the cradle precisely.
5. Optical Sensor On and Off
Notice:
- This function is to save battery power by avoiding the undesired operation. For example, the
button may be pressed or clicked while you carry the mouse to other work environment.
- Some wireless optical mice may not include this battery saving function.
1) Press and hold the wheel button and then press the Mouse Link Button. The optical sensor will be off.
2) Please follow the same instruction to power-on the optical sensor.
6. Charging Notice
1) Recommendation: please do not use the mouse during charge periods.
2) At the first time of usage, please charge the batteries at least 6 to 8 hours.
3) The LED indicator or the scroll wheel on the mouse will light while the mouse is low battery. Please
recharge or change the batteries immediately.
4) Press any button to wake up the mouse while the mouse is in the sleeping mode.
PMU-MRF00041
Wireless Optical Mouse
User's Guide

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Create Date                     : 2004:07:07 13:29:35
Modify Date                     : 2004:07:07 13:29:35
Producer                        : Corel PDF Engine Version 9.397
Author                          : Amanda_Kuo
Creator                         : CorelDRAW Version 9.397
Title                           : PMU-MRF00041
Keywords                        : Wireless Optical Mouse  ¤¤©Ê, v7

EXIF Metadata provided by EXIF.tools