Chicago Electric 67119 Users Manual
67119 f9d9a935-0343-4626-9902-a19e3a5fdbf3 Chicago Electric Router 67119 User Guide |
2015-02-10
: Chicago-Electric Chicago-Electric-67119-Users-Manual-357110 chicago-electric-67119-users-manual-357110 chicago-electric pdf
Open the PDF directly: View PDF 
.
Page Count: 20
1-1/2 HP PLUNGE ROUTER
67119
SET UP AND OPERATING INSTRUCTIONS
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Copyright© 2009 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 2
CONTENTS
IMPORTANT SAFETY
INFORMATION ............................ 3
GENERAL POWER TOOL
SAFETY WARNINGS.......................3
PLUNGE ROUTER SAFETY
WARNINGS ......................................5
VIBRATION SAFETY .........................7
GROUNDING ................................. 8
GROUNDED TOOLS: TOOLS
WITH THREE PRONG PLUGS ....... 8
DOUBLE INSULATED TOOLS:
TOOLS WITH TWO PRONG
PLUGS .............................................9
EXTENSION CORDS ......................... 9
SYMBOLOGY ...................................10
SPECIFICATIONS ........................ 11
INSTRUCTIONS FOR PUTTING
INTO USE .................................. 11
FUNCTIONS ..................................... 11
OPERATING INSTRUCTIONS .... 12
TOOL SET UP ..................................12
INSTALLING BITS ............................12
CUTTING DEPTH ADJUSTMENT ...12
EDGE GUIDE ....................................13
DUST EXTRACTION ADAPTER ......14
WORK PIECE AND WORK AREA
SET UP ..........................................14
GENERAL OPERATING
INSTRUCTIONS ............................ 14
MAINTENANCE AND
SERVICING ............................... 16
CLEANING, MAINTENANCE, AND
LUBRICATION ...............................16
TROUBLESHOOTING ......................17
PARTS LIST ................................. 18
ASSEMBLY DIAGRAM ................ 19
LIMITED 90 DAY WARRANTY .... 20
SKU 67119 For technical questions, please call 1-800-444-3353. Page 3
SAVE THIS MANUAL
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
IMPORTANT SAFETY
INFORMATION
In this manual, on the labeling,
and all other information provid-
ed with this product:
This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that
follow this symbol to avoid
possible injury or death.
DANGER indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
WARNING
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
CAUTION, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
NOTICE is used to
address practices
not related to personal injury.
CAUTION, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
General Power Tool Safety
Warnings
WARNING Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, re and/or serious injury.
Save all warnings and
instructions for future reference.
The term ″power tool″ in the
warnings refers to your mains-
operated (corded) power tool.
Work area safety1.
Keep work area clean and well lit. a.
Cluttered or dark areas invite acci-
dents.
Do not operate power tools in ex-b.
plosive atmospheres, such as in
the presence of ammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
Keep children and bystanders c.
away while operating a power
tool. Distractions can cause you to
lose control.
Electrical safety2.
Power tool plugs must match the a.
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 4
Unmodied plugs and matching out-
lets will reduce risk of electric shock.
Avoid body contact with grounded b.
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
Do not expose power tools to rain c.
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use d.
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
When operating a power tool e.
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduc-
es the risk of electric shock.
If operating a power tool in a f.
damp location is unavoidable, use
a Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of
a GFCI reduces the risk of electric
shock.
Personal safety3.
Stay alert, watch what you are a.
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the inuence of
drugs, alcohol or medication. A
moment of inattention while operat-
ing power tools may result in serious
personal injury.
Use personal protective equip-b.
ment. Always wear eye protec-
tion. Safety equipment such as a
dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. c.
Ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your nger
on the switch or energizing power
tools that have the switch on invites
accidents.
Remove any adjusting key or d.
wrench before turning the power
tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
Do not overreach. Keep proper e.
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear f.
loose clothing or jewelry. Keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can be
caught in moving parts.
If devices are provided for the g.
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce
dust-related hazards.
Only use safety equipment that h.
has been approved by an appro-
priate standards agency. Unap-
proved safety equipment may not
provide adequate protection. Eye
protection must be ANSI-approved
and breathing protection must be
NIOSH-approved for the specic
hazards in the work area.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 5
Power tool use and care4.
Do not force the power tool. Use a.
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
Do not use the power tool if the b.
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
Disconnect the plug from the c.
power source and/or the battery
pack from the power tool before
making any adjustments, chang-
ing accessories, or storing power
tools. Such preventive safety mea-
sures reduce the risk of starting the
power tool accidentally.
Store idle power tools out of the d.
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to oper-
ate the power tool. Power tools are
dangerous in the hands of untrained
users.
Maintain power tools. Check for e.
misalignment or binding of mov-
ing parts, breakage of parts and
any other condition that may af-
fect the power tool’s operation. If
damaged, have the power tool re-
paired before use. Many accidents
are caused by poorly maintained
power tools.
Keep cutting tools sharp and f.
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
Use the power tool, accessories g.
and tool bits etc. in accordance
with these instructions, taking
into account the working condi-
tions and the work to be per-
formed. Use of the power tool
for operations different from those
intended could result in a hazardous
situation.
Service5.
Have your power tool serviced by a.
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
Plunge Router Safety Warnings
Hold power tool by insulated grip-1.
ping surfaces when performing an
operation where cutting tool may
contact hidden wiring or its own
cord. Contact with a ″live″ wire will
make exposed metal parts of the tool
″live″ and shock the operator.
Use clamps or another practical 2.
way to secure and support the
work piece to a stable platform.
Holding the work by hand or against
your body leaves it unstable and may
lead to loss of control.
Use only accessories rated at least 3.
equal to maximum speed marked on
Router.
Only use router bits with a shank di-4.
ameter equal to the size of the tool’s
collet. The collet size is 1/4”.
Make sure the collet nut is securely 5.
tightened before use to prevent the
router bit from slipping during use.
Do not use with base removed.6.
Hold router with both hands. 7.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 6
Keep hands away from the cutting 8.
area. Do not place hands beneath the
workpiece for any reason. Keep the
base of the router in rm contact with
the workpiece while cutting.
Keep Handles dry, clean, and free of 9.
oil or grease. This will permit better
control of the tool.
Do not use damaged bits.10.
Do not lay the Router down until it 11.
has stopped rotating completely.
Hold the Router rmly when starting, 12.
as startup rotation creates signicant
torque.
Hold the Router rmly while cutting. 13.
The action of the bit against the work-
piece can cause it to “kick out”, jump-
ing rapidly away from the workpiece.
This can be caused by an improper
type of bit, or a dull bit.
Do not handle the Router bit immedi-14.
ately after cutting. It may be very hot,
potentially causing burns or injury.
Avoid overloading the tool. If the 15.
speed drops abnormally, decrease
the pressure on the bit immediately.
Do not apply excessive pressure to
the router while cutting.
Always use sharpened bits. If the bit 16.
stops abruptly, or the bit becomes
blocked, remove the Router from the
workpiece and shut it off.
Do not start the Router while the bit 17.
is in contact with the workpiece. Allow
the tool to reach its normal operating
speed before applying the bit to the
workpiece.
Use caution when setting the Lock-18.
ing Trigger Switch. Be aware that the
router will continue to operate while
the locking mechanism is engaged.
Do not lay the router down or hand it
to another person while the locking
mechanism is engaged.
Before Routing, run the tool for about 19.
10 seconds to ensure that all moving
parts are running smoothly and there
are no loose parts, rattles, or spark-
ing that would indicate damage.
Maintain labels and nameplates on 20.
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
Avoid unintentional starting. Prepare 21.
to begin work before turning on the
tool.
Do not lay the tool down until it has 22.
come to a complete stop. Moving
parts can grab the surface and pull
the tool out of your control.
When using a handheld power tool, 23.
maintain a rm grip on the tool with
both hands to resist starting torque.
Do not leave the tool unattended 24.
when it is plugged into an electrical
outlet. Turn off the tool, and unplug it
from its electrical outlet before leav-
ing.
This product is not a toy. Keep it out 25.
of reach of children.
People with pacemakers should 26.
consult their physician(s) before use.
Electromagnetic elds in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:
• Avoid operating alone.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 7
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
WARNING: Some dust created by 27.
power sanding, sawing, grinding, drill-
ing, and other construction activities,
contains chemicals known [to the
State of California] to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and ce-
ment or other masonry products
• Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures var-
ies, depending on how often you do
this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to lter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
WARNING: Handling the cord on 28.
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
The warnings, precautions, and in-29.
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Vibration Safety
This tool vibrates during use. Re-
peated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
Anyone using vibrating tools regu-1.
larly or for an extended period should
rst be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, ner-
vous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any symptoms
related to vibration (such as tingling,
numbness, and white or blue ngers),
seek medical advice as soon as pos-
sible.
Do not smoke during use. Nico-2.
tine reduces the blood supply to the
hands and ngers, increasing the risk
of vibration-related injury.
Wear suitable gloves to reduce the 3.
vibration effects on the user.
Use tools with the lowest vibration 4.
when there is a choice.
Include vibration-free periods each 5.
day of work.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 8
Grip tool as lightly as possible (while 6.
still keeping safe control of it). Let
the tool do the work.
To reduce vibration, maintain the tool 7.
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
SAVE THESE
INSTRUCTIONS.
GROUNDING
TO PREVENT
ELECTRIC SHOCK
AND DEATH FROM
INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualied
electrician if you are in doubt
as to whether the outlet is
properly grounded. Do not
modify the power cord plug
provided with the tool. Never
remove the grounding prong
from the plug. Do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
t the outlet, have a proper
outlet installed by a qualied
electrician.
Grounded Tools: Tools with Three
Prong Plugs
3-Prong Plug and Outlet
Tools marked with “Grounding Re-1.
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break
down, grounding provides a low
resistance path to carry electricity
away from the user, reducing the risk
of electric shock. (See 3-Prong Plug
and Outlet.)
The grounding prong in the plug is 2.
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-Prong Plug
and Outlet.)
The tool must be plugged into an 3.
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
SKU 67119 For technical questions, please call 1-800-444-3353. Page 9
Double Insulated Tools: Tools
with Two Prong Plugs
Outlets for 2-Prong Plug
Tools marked “Double Insulated” do 1.
not require grounding. They have
a special double insulation system
which satises OSHA requirements
and complies with the applicable
standards of Underwriters Labora-
tories, Inc., the Canadian Standard
Association, and the National Electri-
cal Code. (See Outlets for 2-Prong
Plug.)
Double insulated tools may be used 2.
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
Extension Cords
Grounded1. tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
As the distance from the supply outlet 2.
increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and pos-
sible tool damage.
(See Table A.)
The smaller the gauge number of the 3.
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table A.)
When using more than one exten-4.
sion cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table A.)
If you are using one extension cord 5.
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table A.)
If you are using an extension cord 6.
outdoors, make sure it is marked with
the sufx “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
Make sure the extension cord is prop-7.
erly wired and in good electrical con-
dition. Always replace a damaged
extension cord or have it repaired by
a qualied electrician before using it.
Protect the extension cords from 8.
sharp objects, excessive heat, and
damp or wet areas.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 10
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25’
50’
75’
100’
150’
0 – 2.0 18 18 18 18 16
2.1 – 3.4 18 18 18 16 14
3.5 – 5.0 18 18 16 14 12
5.1 – 7.0 18 16 14 12 12
7.1 – 12.0 18 14 12 10 -
12.1 – 16.0 14 12 10 - -
16.1 – 20.0 12 10 - - -
TABLE A
* Based on limiting the line
voltage drop to ve volts at
150% of the rated amperes.
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
V~ Volts Alternating Current
AAmperes
n0 xxxx/min. No Load Revolutions per Minute
(RPM)
SKU 67119 For technical questions, please call 1-800-444-3353. Page 11
SPECIFICATIONS
Power 1-1/2 HP
Electrical Input 120 V~ / 60 Hz / 10 A
Motor Speed 11,000 - 28,000 RPM (No
Load)
Collet Capacity 1/4”
Maximum
Plunge 2-1/8”
Depth
Measurements 1/16” increments
Depth Stop 4-stage turret stop
E194601
93MA
UNPACKING
When unpacking, make sure that the
item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight
Tools at 1-800-444-3353 as soon as possible.
INSTRUCTIONS FOR
PUTTING INTO USE
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before set up, assembly, or
making any adjustments to
the tool.
Note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
Functions
Trigger
Switch
(60)
Depth
of Cut
Scale
Collet Nut (50)
Dust Extraction
Adapter
Speed Adjuster (4)
Pointer
(28)
Chip Shield (70)
Plunge Lock
Lever (32)
Depth
Stop Bar
(30)
Thumb
Screw
Thumb
Screw
(81) Base Plate
Figure 1
Edge Guide
Spanner
Wrench (51)
Thumb Screw (81)
Adjusting
Knob (26)
Spindle
Spindle
Lock
Button
(46)
Depth
Stop
Turret
(67)
Lock-on Button
SKU 67119 For technical questions, please call 1-800-444-3353. Page 12
OPERATING INSTRUCTIONS
Read the ENTIRE IMPORTANT
SAFETY INFORMATION
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Tool Set Up
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before preparing for
operation.
Installing Bits
Chip
Shield
(70)
Collet Nut (50)
Spindle Lock Button (46) Spindle
Figure 2
1. Unthread the Screw (85) holding the
Chip Shield (70) in place and remove
the Chip Shield.
Lock the Plunge Lock Lever (32) in 2.
place to keep the shaft stationary.
Depress the Spindle Lock Button (46) 3.
and rotate the Spindle until it locks in
place. Keep the Spindle Lock Button
depressed through step 6.
Use the Spanner Wrench (51) to 4.
loosen the Collet Nut (50).
Insert the bit all the way into the 5.
Collet. CAUTION! Bits are sharp,
Handle with care.
Securely tighten Collet Nut.6.
Release the Spindle Lock Button.7.
Pull up the Lock Lever to free the 8.
shaft.
Replace the Chip Shield.9.
Cutting Depth Adjustment
Depth
of Cut
Figure 3
Depth
Adjusting
Bolt (29)
Depth
Stop
Turret
(67) Screw
(85)
Depth
Stop
Bar (30)
The depth of cut is equal to the dis-
tance between the lower end of the
Depth Adjusting Bolt (29) and the
section of the Depth Stop Turret (67)
directly below the Depth Stop Bar
(30). First, install the bit you will use
for the cut, then adjust the Router as
follows to set up the desired cutting
depth.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 13
Loosen the Thumb Screw so that the 1.
Depth Stop Bar (30) can slide freely.
Rotate the Adjusting Knob (26) until 2.
the Depth Adjusting Bolt (29) pro-
trudes about 1/4” from the Depth
Stop Bar.
Rotate the Depth Stop Bar to the left 3.
so that the indexing mark along the
top of the Bar is visible from under
the Pointer (28).
Hold the Bar and rotate the Adjust-4.
ing Knob until the Zero mark along
the base of the adjusting Knob aligns
with the indexing line.
Rotate the Depth Stop Turret (67) to 5.
the lowest setting.
Loosen the Plunge Lock Lever (32).6.
Lower the Router body until the bit 7.
just touches the workpiece.
Tighten the Plunge Lock Lever.8.
Use one of the following two ways to 9.
adjust the router depth:
Increment Guide
Pointer
(28)
Adjusting
Knob (26)
Depth
Stop
Bar
(30)
Thumb Screw
Figure 4
• Position the Depth Adjusting Bolt
(29), so that it is touching the Depth
Stop Turret (67). Slide the Pointer
(28) to zero on the Increment Guide,
then raise the Depth Stop Bar to the
desired height using the Pointer and
the Increment Guide. Tighten the
Thumb Screw to hold the Stop Bar in
place.
Or, using a piece of wood the thick-•
ness of the desired cut, place the
piece of wood on the Lowest level
of the Depth Stop Turret (67). Adjust
the Depth Stop Bar (29) so that the
Depth Stop Bolt (29) rests on the
piece of wood and tighten in place
with the Thumb Screw.
Note: For marginal depth adjustments,
raise the Depth Adjusting Bolt (29)
(located inside the Depth Stop Bar)
in ne increments by turning the
Adjusting Knob (26) to set the exact
desired depth of cut. Use the Pointer
(28) along with the increment guide to
help make the adjustment.
Loosen the Plunge Lock Lever and 10.
allow the router to return to its original
position.
Edge Guide
Thumb Screws (81)
Edge Guide
Fence Bars
Figure 5
To attach the Edge Guide when mak-
ing straight cuts:
Loosen the Thumb Screws (81).a.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 14
Slide the bars on the Edge Guide b.
into the slots on the Base of the
Router with the fence facing the
workpiece.
Note: The Edge Guide can be inserted
into either side of the tool to make
cuts along the left or right side of the
material.
Adjust the distance between the c.
router bit and the fence of the Edge
Guide to the desired setting.
Tighten the Thumb Screws (81).d.
Dust Extraction Adapter
If desired, attach a vacuum cleaner 1.
hose to the Dust Extraction Adapter
(62).
Be sure the hose, vacuum cleaner, 2.
and power cord are out of the way
and properly secured so they will not
tip over or interfere with the Router
or workpiece. If they cannot be posi-
tioned safely, they should not be used
with the Router.
Turn on the vacuum before turning on 3.
the Router.
Empty the vacuum cleaner as need-4.
ed only after turning off and unplug-
ging both the vacuum cleaner and the
Router.
Work Piece and Work Area Set Up
Designate a work area that is clean 1.
and well-lit. The work area must not
allow access by children or pets to
prevent distraction and injury.
Route the power cord along a safe 2.
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
The power cord must reach the work
area with enough extra length to al-
low free movement while working.
Secure loose work pieces using a 3.
vise or clamps (not included) to pre-
vent movement while working.
Make sure there are no metal objects 4.
in the wood which might make con-
tact with the router bit.
Hold Router handles rmly with both 5.
hands.
Always hold the Router from the 6.
front, ensuring that the Chip Shield
(70) is between you and the bit.
Keep hands away from rotating bit. 7.
Unplug the tool and wait until the bit
stops rotating completely before mak-
ing adjustments.
Do not touch the bit right after cutting. 8.
It becomes very hot.
Before cutting material, turn the 9.
Router on. Watch and feel for vibra-
tion which could indicate an improp-
erly installed bit.
Turn the Router off when not actually 10.
cutting. Do not leave running.
General Operating Instructions
Note: Use two or more passes for deep
cuts, especially in the case of hard-
wood. Do not attempt to cut deeper
than 5/8” in a single pass. Turn the
Depth Stop Turret (67) so that the
rst pass will be less than 5/8” deep,
then rotate the Turret one step for
each progressive pass, until the nal
depth is achieved.
CAUTION: When rst turning on the
Router, grip the Handles rmly as the
SKU 67119 For technical questions, please call 1-800-444-3353. Page 15
tool may try to twist from the strong
initial torque.
Note: The Router bit should always be fed
into the stock from left to right so as
to match the clockwise rotation of the
router. When cutting outside edges,
rotate the router counterclockwise.
Rotate it clockwise when cutting in-
side edges.
Note: Make practice cuts at different
speeds in scrap material until you are
able to produce a smooth cut with no
burnishing or burn marks. Burn marks
are caused by moving too slowly
through the wood. Feeding the Rout-
er too quickly, or trying to remove too
much material in a single pass cre-
ates a rough cut and can overload
the motor.
Set the desired speed by turning the 1.
Speed Adjuster (4). Use lower set-
tings for large diameter bits and high-
er settings for small diameter bits.
Place the Router directly above the 2.
point you plan to cut. Verify that there
are no obstructions in the cutting
path.
Verify that the Plunge Lock Lever (32) 3.
is loose.
Turn on the Router. The Router can 4.
be powered with or without the Lock-
on Button engaged.
To power the Router so that the •
power is on only while the Trigger
Switch is depressed: depress and
hold in the Trigger Switch (60). To
stop the Router from this setting,
release the Trigger Switch.
To power the Router continuously, •
without holding in any buttons or
switches, depress and hold in the
Trigger Switch (60), then push the
Lock-on Button. Release the Trig-
ger Switch, then the Lock-on Button.
To stop the Router from this setting,
press and release the Trigger Switch.
Allow the bit to come to full speed, 5.
slowly engage material. DO NOT
force the Router down into the mate-
rial.
When the tool reaches its pre-set 6.
depth, tighten the Plunge Lock Lever
(32).
Once you have nished the cut, loos-7.
en the Plunge Lock Lever and allow
the spring to lift the Router directly
out of the workpiece.
When nished, raise the Router so 8.
the bit is clear of the material, then
release the Trigger Switch, or press
and release the Trigger Switch if the
Lock-on Button was set. Do not set
the Router down until the bit has
come to a complete stop.
When making more than one pass 9.
to achieve the desired cutting depth,
turn the Depth Stop Turret to the next
lower level and repeat the cut. Re-
peat again as needed until the cut is
the desired depth.
To prevent accidents, disconnect the 10.
power supply after use. Clean, then
store the tool indoors out of children’s
reach.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 16
MAINTENANCE AND
SERVICING
Procedures not specically
explained in this manual
must be performed only by a
qualied technician.
TO PREVENT
SERIOUS INJURY
FROM ACCIDENTAL
OPERATION:
Turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
TO PREVENT SERIOUS
INJURY FROM TOOL
FAILURE:
Do not use damaged
equipment. If abnormal noise
or vibration occurs, have the
problem corrected before
further use.
Cleaning, Maintenance, and
Lubrication
BEFORE EACH USE,1. inspect the
general condition of the tool. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
AFTER USE,2. wipe external surfaces
of the tool with a clean cloth. Do not
use any abrasive or solvent-based
cleaners.
Regularly clean all ventilation open-3.
ings by periodically brushing with a
soft brush and/or blowing clear with
compressed air.
4. WARNING! If the supply cord of
this power tool is damaged, it must
be replaced only by a qualied
service technician.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 17
Troubleshooting
Problem Possible Causes Likely Solutions
Tool will not start. Cord not connected.1.
No power at outlet. 2.
Tool’s thermal reset breaker 3.
tripped (if equipped).
Internal damage or wear. 4.
(Carbon brushes or switch, for
example.)
Check that cord is plugged in.1.
Check power at outlet. If outlet is 2.
unpowered, turn off tool and check circuit
breaker. If breaker is tripped, make sure
circuit is right capacity for tool and circuit
has no other loads.
Turn off tool and allow to cool. Press 3.
reset button on tool.
Have technician service tool.4.
Tool operates slowly. Power being reduced by long or
small diameter extension cord.
Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
Performance
decreases over time.
Accessory dull or damaged. 1.
Carbon brushes worn or 2.
damaged.
Keep cutting accessories sharp. 1.
Replace as needed.
Have qualied technician replace 2.
brushes.
Excessive noise or
rattling.
Internal damage or wear. (Carbon
brushes or bearings, for example.)
Have technician service tool.
Overheating. Forcing tool to work too fast.1.
Accessory misaligned. 2.
Accessory dull or damaged. 3.
Blocked motor housing vents. 4.
Motor being strained by long or 5.
small diameter extension cord.
Allow tool to work at its own rate.1.
Check and correct accessory to fence 2.
and/or table alignment.
Keep cutting accessories sharp. 3.
Replace as needed.
Wear ANSI-approved safety goggles and 4.
NIOSH-approved dust mask/respirator
while blowing dust out of motor using
compressed air.
Eliminate use of extension cord. If 5.
an extension cord is needed, use one
with the proper diameter for its length
and load. See Extension Cords in
GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the
tool. Disconnect power supply before service.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 67119 For technical questions, please call 1-800-444-3353. Page 18
Part Description Qty
1 Tapping Screw 8
2 Cover 1
3 Screw 2
4 Speed Adjuster 1
5 Tapping Screw 5
6 Tapping Screw 2
7 Cover 1
8 Cover 1
9 Tapping Screw 2
10 Epoxy Board 2
11 Brush Holder 2
12 Carbon Brush 2
13 Motor Housing 1
14 Spring 1
15 Washer 1
16 Bearing 1
17 Stator 1
18 Tapping Screw 2
19 Rotor 1
20 Circlips for Shaft 3
21 Fan Bafe 1
22 Screw 2
23 Bearing Clamping Plate 1
24 Ball Bearing 608 R5 1
25 Screw 1
26 Adjusting Knob 1
27 O-Ring 1
28 Depth Indicator 1
29 Depth Adjusting Bolt 1
30 Depth Stop Bar 1
31 Screw 1
32 Plunge Lock Lever 1
33 Slotted Set Screw 1
34 Wave Washer 1
35 Nut 1
36 Left Handle Cover 1
37 Hexagon Socket Screw 4
38 Spring Washer 5
39 Plain Washer 5
40 Left Handle 1
41 Plunge Frame 1
42 Tapping Screw 4
43 Nut 1
Part Description Qty
44 Spring 2
45 Spindle Lock 1
46 Spindle Lock Button 1
47 Lock Cover 1
48 Screw 2
49 Collet 1
50 Collet Nut 1
51 Collet Wrench 1
52 Inner Wire 1
53 Right Handle Cover 1
54 Right Handle 1
55 Cord Anchor 1
56 Screw 2
57 Cord Guard 1
58 Power Cord and Plug 1
59 Cover 1
60 Switch 1
61 Spring 2
62 Dust Extraction Adapter 1
63 Hexagon Nut 2
64 Bellows Seal 2
65 Screw 4mm x 0.7 1
66 Waver Washer 1
67 Depth Stop Turret 1
68 Steel Ball Ø 5mm 1
69 Spring 1
70 Chip Shield 1
71 Bottom Support 1
72 Guiding Rod 2
73 Base Plate 1
74 Screw 3
75 Guide Bushing 1
76 Screw 2
77 Parallel Guide 1
78 Plain Washer 2
79 Spring Washer 2
80 Screw 2
81 Thumb Screw 3
82 Spring Pin 2
83 Lower Cover 1
84 Plunge Rod 2
85 Screw, Chip Shield 4mm x 0.7 1
PARTS LIST
SKU 67119 For technical questions, please call 1-800-444-3353. Page 19
ASSEMBLY DIAGRAM
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
85
SKU 67119 For technical questions, please call 1-800-444-3353. Page 20
LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection veries the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specic legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
