Chicago Electric 92115 Users Manual

92115 92115

92115 dde88f50-7b3a-4c32-8684-af7d81fdc105 Chicago Electric Trimmer 92115 User Guide |

2015-02-10

: Chicago-Electric Chicago-Electric-92115-Users-Manual-357143 chicago-electric-92115-users-manual-357143 chicago-electric pdf

Open the PDF directly: View PDF PDF.
Page Count: 14

DownloadChicago-Electric Chicago-Electric-92115-Users-Manual-  Chicago-electric-92115-users-manual
Open PDF In BrowserView PDF
14 Gauge
Swivel Head Shear
Model 92115
Set up and Operating Instructions

Visit our website at: http://www.harborfreight.com

	Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10f

	NOTICE is used to
address practices not
related to personal injury.

Save This Manual
Keep this manual for the safety warnings
and precautions, assembly, operating,
inspection, maintenance and cleaning
procedures. Write the product’s serial number
in the back of the manual near the assembly
diagram (or month and year of purchase if
product has no number). Keep this manual
and the receipt in a safe and dry place for
future reference.

	CAUTION, without the
safety alert symbol, is
used to address practices not
related to personal injury.

General Power Tool Safety Warnings
	WARNING Read all safety warnings
and instructions. Failure to follow the
warnings and instructions may result
in electric shock, fire and/or serious
injury.
Save all warnings and instructions
for future reference.
The term ″power tool″ in the warnings
refers to your mains-operated (corded)
power tool.

Important SAFETY
Information
In this manual, on the labeling, and
all other information provided with
this product:
	This is the safety alert
symbol. It is used to alert
you to potential personal
injury hazards. Obey all
safety messages that follow
this symbol to avoid possible
injury or death.

1.	

a.	Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b.	Do not operate power tools in
explosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.

	DANGER indicates a
hazardous situation
which, if not avoided, will result
in death or serious injury.
	WARNING indicates a
hazardous situation
which, if not avoided, could
result in death or serious injury.
	CAUTION, used with
the safety alert
symbol, indicates a hazardous
situation which, if not avoided,
could result in minor or moderate
injury.

Work area safety

c.	 Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose
control.
2.	

Electrical safety
a.	Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with grounded power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b.	Avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is an

Page 2

For technical questions, please call 1-800-444-3353.

SKU 92115

trigger or energizing power tools that
have the trigger depressed invites
accidents.

increased risk of electric shock if your
body is grounded.
c.	 Do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.

d.	Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a
rotating part of the power tool may result
in personal injury.

d.	Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk of
electric shock.

e.	Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool
in unexpected situations.
f.	 Dress properly. Do not wear loose
clothing or jewelry. Keep your hair,
clothing and gloves away from
moving parts. Loose clothes, jewelry
or long hair can be caught in moving
parts.

e.	When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces
the risk of electric shock.
f.	 If operating a power tool in a damp
location is unavoidable, use a
Ground Fault Circuit Interrupter
(GFCI) protected supply. Use of a
GFCI reduces the risk of electric shock.
3.	

g.	If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
these devices can reduce dust-related
hazards.

Personal safety

h.	Only use safety equipment that has
been approved by an appropriate
standards agency. Unapproved
safety equipment may not provide
adequate protection. Eye protection
must be ANSI-approved and breathing
protection must be NIOSH-approved for
the specific hazards in the work area.

a.	Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result
in serious personal injury.
b.	Use personal protective equipment.
Always wear eye protection. Safety
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate
conditions will reduce personal injuries.
c.	 Prevent unintentional starting.
Ensure the trigger is released before
connecting to power source, picking
up or carrying the tool. Carrying
power tools with your finger on the
SKU 92115

4.	

Power tool use and care
a.	Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate
for which it was designed.
b.	Do not use the power tool if the
trigger does not turn it on and off.
Any power tool that cannot be controlled
with the trigger is dangerous and must
be repaired.

For technical questions, please call 1-800-444-3353.

Page 3

c.	 Disconnect the plug from the
power source before making any
adjustments, changing accessories,
or storing power tools. Such
preventive safety measures reduce
the risk of starting the power tool
accidentally.
d.	Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
e.	Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any
other condition that may affect the
power tool’s operation. If damaged,
have the power tool repaired before
use. Many accidents are caused by
poorly maintained power tools.
f.	 Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g.	Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions and
the work to be performed. Use of
the power tool for operations different
from those intended could result in a
hazardous situation.
5.	

Service
a.	Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool
is maintained.

Page 4

Shear Safety Warnings
1.	

Handle sheet metal with care. Sheet
metal will have sharp edges. Wear
ANSI-approved safety goggles, heavyduty work gloves, long sleeve shirt,
and jeans when working with sheet
metal.

2.	

Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or missing,
contact Harbor Freight Tools for a
replacement.

3.	

Avoid unintentional starting. Prepare to
begin work before turning on the tool.

4.	

Do not lay the tool down until it has come
to a complete stop. Moving parts can
grab the surface and pull the tool out of
your control.

5.	

When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.

6.	

Do not leave the tool unattended when
it is plugged into an electrical outlet.
Turn off the tool, and unplug it from its
electrical outlet before leaving.

7.	

This product is not a toy. Keep it out of
reach of children.

8.	

People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close proximity
to heart pacemaker could cause
pacemaker interference or pacemaker
failure. In addition, people with
pacemakers should:
• Avoid operating alone.
• Do not use with trigger locked on.
• Properly maintain and inspect to avoid
electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit
Interrupter (GFCI) should also be

For technical questions, please call 1-800-444-3353.

SKU 92115

implemented – it prevents sustained
electrical shock.
9.	

WARNING: Some dust created by power
sanding, sawing, grinding, drilling, and
other construction activities, contains
chemicals known [to the State of
California] to cause cancer, birth defects
or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and
cement or other masonry products
• Arsenic and chromium from chemically
treated lumber
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: work in a well ventilated
area, and work with approved safety
equipment, such as those dust masks
that are specially designed to filter out
microscopic particles. (California Health
& Safety Code § 25249.5, et seq.)

injury, particularly to the hands, arms
and shoulders. To reduce the risk of
vibration-related injury:
1.	

Anyone using vibrating tools regularly
or for an extended period should first
be examined by a doctor and then have
regular medical check-ups to ensure
medical problems are not being caused
or worsened from use. Pregnant
women or people who have impaired
blood circulation to the hand, past hand
injuries, nervous system disorders,
diabetes, or Raynaud’s Disease
should not use this tool. If you feel any
symptoms related to vibration (such as
tingling, numbness, and white or blue
fingers), seek medical advice as soon as
possible.

2.	

Do not smoke during use. Nicotine
reduces the blood supply to the hands
and fingers, increasing the risk of
vibration-related injury.

10.	 WARNING: Handling the cord on this
product will expose you to lead, a
chemical known to the State of California
to cause cancer, and birth defects or
other reproductive harm. Wash hands
after handling. (California Health &
Safety Code § 25249.5, et seq.)

3.	

Wear suitable gloves to reduce the
vibration effects on the user.

4.	

Use tools with the lowest vibration when
there is a choice.

5.	

Include vibration-free periods each day
of work.

11.	 The warnings, precautions, and
instructions discussed in this instruction
manual cannot cover all possible
conditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.

6.	

Grip tool as lightly as possible (while still
keeping safe control of it). Let the tool
do the work.

7.	

To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.

Vibration Safety

	 Save these
instructions.

This tool vibrates during use. Repeated
or long-term exposure to vibration may
cause temporary or permanent physical
SKU 92115

For technical questions, please call 1-800-444-3353.

Page 5

preceding illustration.
(See Outlets for 2-Prong Plug.)

Grounding
	

To prevent
electric shock
and death from incorrect
grounding wire
connection:
Check with a qualified electrician
if you are in doubt as to whether
the outlet is properly grounded.
Do not modify the power cord
plug provided with the tool.
Never remove the grounding
prong from the plug. Do not use
the tool if the power cord or plug
is damaged. If damaged, have it
repaired by a service facility
before use. If the plug will not fit
the outlet, have a proper outlet
installed by a qualified
electrician.

Double Insulated Tools: Tools with
Two Prong Plugs

Extension Cords
1.	

Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three wire
extension cord.

2.	

As the distance from the supply outlet
increases, you must use a heavier gauge
extension cord. Using extension cords
with inadequately sized wire causes a
serious drop in voltage, resulting in loss
of power and possible tool damage.
(See Table A.)

3.	

The smaller the gauge number of the
wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry
a higher current than a 16 gauge cord.
(See Table A.)

4.	

When using more than one extension
cord to make up the total length, make
sure each cord contains at least the
minimum wire size required.
(See Table A.)

5.	

If you are using one extension cord for
more than one tool, add the nameplate
amperes and use the sum to determine
the required minimum cord size.
(See Table A.)

6.	

If you are using an extension cord
outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it
is acceptable for outdoor use.

7.	

Make sure the extension cord is properly
wired and in good electrical condition.
Always replace a damaged extension
cord or have it repaired by a qualified
electrician before using it.

Outlets for 2-Prong Plug
1.	

2.	

Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian
Standard Association, and the National
Electrical Code.
Double insulated tools may be used in
either of the 120 volt outlets shown in the
Page 6

For technical questions, please call 1-800-444-3353.

SKU 92115

8.	

Protect the extension cords from sharp
objects, excessive heat, and damp or
wet areas.
RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS*
(120/240 VOLT)

(at full load)

50’

75’

100’

150’

EXTENSION CORD
LENGTH
25’

NAMEPLATE
AMPERES
0 – 2.0

18

18

18

18

16

2.1 – 3.4

18

18

18

16

14

3.5 – 5.0

18

18

16

14

12

5.1 – 7.0

18

16

14

12

12

7.1 – 12.0

18

14

12

10

-

12.1 – 16.0

14

12

10

-

-

16.1 – 20.0

12

10

-

-

-

TABLE A

* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.

Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.

V~
A

Volts Alternating Current
Amperes
No Load Revolutions per Minute

n0 xxxx/min. (RPM)

SKU 92115

For technical questions, please call 1-800-444-3353.

Page 7

Specifications

Operating Instructions
	Read the entire Important
Safety Information
section at the beginning of this
manual including all text under
subheadings therein before set up
or use of this product.

Electrical Input 120 V~ / 60 Hz / 2.2 A (no load)
Motor Speed
0-2500 RPM (no load)
Capacity
Up to 14 gauge sheet metal
Up to 18 gauge stainless steel
@ 150 inches per minute
Cutting Blades Tungsten Carbide Steel
Cutting Head Swivels 360°

SWIVELING THE CUTTER HEAD

Unpacking

	To prevent
serious injury
from accidental
operation:
Release the Trigger and unplug
the tool from its electrical outlet
before adjusting tool or installing
accessories.

When unpacking, make sure that the
item is intact and undamaged. If any parts
are missing or broken, please call Harbor
Freight Tools at 1-800-444-3353 as soon as
possible.

1.	

Put on heavy-duty work gloves and
ANSI-approved safety goggles to avoid
injury.
Figure 1

2.	

Loosen the three hex head bolts using
the hex wrench provided with this tool see Figure 1.

3.	

Firmly grip the cutter head and twist it to
the desired position. Tighten the three
hex bolts to keep the Cutter Head in that
position.

REV 06f, 10a

Page 8

For technical questions, please call 1-800-444-3353.

SKU 92115

Work Piece and Work Area Set Up
1.	

2.	

Designate a work area that is clean and
well-lit. The work area must not allow
access by children or pets to prevent
distraction and injury.
Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage. The
power cord must reach the work area
with enough extra length to allow free
movement while working.

3.	

Secure loose work pieces using a vise
or clamps (not included) to prevent
movement while working.

4.	

There must not be objects, such as utility
lines, nearby that will present a hazard
while working.

5.	

Make a practice cut on a piece of scrap
material before cutting the work material.
This will allow you to be sure you are
familiar with the way the tool operates,
and that the cut can be made properly.

SKU 92115

General Operating Instructions
1.	

Wear ANSI-approved safety goggles,
heavy-duty work gloves, long sleeve
shirt, and jeans.

2.	

Plug the tool into an appropriate, breaker
switch protected power outlet.

3.	

Position the jaws of the Shear over the
edge of the sheet metal you will cut.

4.	

Squeeze the Power Switch to begin
cutting the metal. The Power Switch is
variable, allowing you to vary the cutting
speed by the amount you squeeze it. As
you squeeze more, the tool will increase
speed, and it will cut more slowly as you
release the Power Switch.

5.	

Move the Cutting Blades along the
desired cutting line in the work material.

6.	

On large pieces of sheet metal, you may
wish to swivel the head to one side or
the other to prevent interference of the
tool handle with the work material. See
previous page for full instructions on how
to swivel the Cutting Head.

7.	

To prevent accidents, turn off the tool
and disconnect its power supply after
use. Clean, then store the tool indoors
out of children’s reach.

For technical questions, please call 1-800-444-3353.

Page 9

Maintenance And
Servicing
	 Procedures not specifically
explained in this manual must
be performed only by a qualified
technician.
	

To prevent
serious injury
from accidental
operation:
Release the Trigger and unplug
the tool from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
To prevent serious injury
from tool failure:
Do not use damaged equipment.
If abnormal noise or vibration
occurs, have the problem
corrected before further use.
1.	

Right
Blade (24)

Cutting
Head
(22)

Center
Blade
(25)
Bushing
(26)
Head
Bolts (28)

Left Blade (27)

3.	

The three Blades (24, 25, and 27) and
the two Bushings (26) will be loose.

4.	

Clean, replace or sharpen the blades as
required. Replace blades as a set only.

5.	

Reassemble by repositioning the Blades,
and Bushings as illustrated. Replace the
Head Bolts and tighten them securely.

6.	

Test the product to be sure that it is
working properly.

7.	

The Left and Right Blades (24, 27) are
slotted. They can be adjusted to change
the direction of the curl of waste material.
To adjust:

BEFORE EACH USE, inspect the
general condition of the tool. Check for
loose hardware, misalignment or binding
of moving parts, cracked or broken parts,
damaged electrical wiring, and any
other condition that may affect its safe
operation.

a.	Unplug the tool.

2.	

After Use, wipe external surfaces of
the tool with clean cloth.

d.	Tighten the Head Bolts (28).

3.	

WARNING! If the supply cord of
this power tool is damaged, it must be
replaced only by a qualified service
technician.

Blade Maintenance
1.	

Unplug the tool.

2.	

Using the Hex Tool, remove the three
Head Bolts (28).

b.	Loosen all three Head Bolts (28).
c.	 Make a slight adjustment to the Left or
Right Blade (24, 27) as needed.
e.	Test the direction of the waste curl and
repeat the steps above as needed.
Note: If the Head Bolts (28) are
overtightened, then the Center Blade
(25) will not move freely enough, causing
premature wear, or possibly preventing
the tool from operating.
If the Head Bolts are not tight enough,
the tool will not make a smooth cut in the
material.

REV 06f, 07j, 10a

Page 10

For technical questions, please call 1-800-444-3353.

SKU 92115

Troubleshooting
Problem
Tool will not start.

Possible Causes
1.	 Cord not connected.
2.	 No power at outlet.

3.	 Tool’s thermal reset breaker
tripped (if equipped).
4.	 Internal damage or wear.
(Carbon brushes or switch, for
example.)
5.	 Head Bolts (28) too tight.
Tool operates slowly. 1.	 Dirty, worn or damaged blades.
2.	 Extension cord too long or wire
size too small.
3.	 Head Bolts (28) too tight.
Performance
1.	 Blades dull or damaged.
decreases over time. 2.	 Carbon brushes worn or
damaged.
Cut not smooth.
Head Bolts (28) loose.
Excessive noise or
rattling.
Overheating.

Internal damage or wear. (Carbon
brushes or bearings, for example.)
1.	 Forcing tool to work too fast.
2.	 Blades misaligned.
3.	 Blades dull or damaged.
4.	 Blocked motor housing vents.

5.	 Motor being strained by long or
small diameter extension cord.

Likely Solutions
1.	 Check that cord is plugged in.
2.	 Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker. If breaker
is tripped, make sure circuit is right capacity for
tool and circuit has no other loads.
3.	 Turn off tool and allow to cool. Press reset button
on tool.
4.	 Have technician service tool.

5.	 Make sure that Head Bolts (28) are not
excessively tight.
1.	 Clean or replace blades.
2.	 Eliminate use of extension cord. If an extension
cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
3.	 Make sure that Head Bolts (28) are not
excessively tight.
1.	 Keep blades sharp. Replace as needed.
2.	 Have qualified technician replace brushes.
Tighten Head Bolts (28) enough to properly hold the
Left and Right Blades (24, 27) in place.
Have technician service tool.
1.	 Allow tool to work at its own rate.
2.	 Check and correct blades to fence and/or table
alignment.
3.	 Keep blades sharp. Replace as needed.
4.	 Wear ANSI-approved safety goggles and NIOSHapproved dust mask/respirator while blowing dust
out of motor using compressed air.
5.	 Eliminate use of extension cord. If an extension
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords in
GROUNDING section.

	Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.

REV 10a

SKU 92115

For technical questions, please call 1-800-444-3353.

Page 11

PLEASE READ THE FOLLOWING CAREFULLY
The manufacturer and/or distributor has provided the parts list and assembly
diagram in this manual as a reference tool only. Neither the manufacturer or
distributor makes any representation or warranty of any kind to the buyer that he
or she is qualified to make any repairs to the product, or that he or she is qualified
to replace any parts of the product. In fact, the manufacturer and/or distributor
expressly states that all repairs and parts replacements should be undertaken by
certified and licensed technicians, and not by the buyer. The buyer assumes all risk
and liability arising out of his or her repairs to the original product or replacement
parts thereto, or arising out of his or her installation of replacement parts thereto.

Parts List
Part
1
2
3
4
5
6
7
8
9
10
11
12

Description
Housing
Rear Motor Bushing
Motor Armature
Washer
Motor Mounting Bolt
Mid Motor Bushing
Motor Seal
Motor Winding
Front Motor Bushing
Front Housing
Shear Head Seal
Head Rear Bushing

Qty.

Part

Description

Qty.

Part

1
1
1
2
2
1
1
1
1
1
1
1

13
14
15
16
17
18
19
20
21
22*
23*
24^

Head Gear
Head Gear Housing
Washer
Head Housing Bolt
Head Rear Bearing
Head Center Bushing
Head Seal
Head Front Bearing
Head Front Bushing
Cutting Head
Insert Nut
Right Blade

1
1
3
3
1
1
1
1
1
1
3
1

25^
26^
27^
28*
29
30
31
32
33
34
35

Description

Qty.

Center Blade
Bushing
Left Blade
Head Bolt
Trigger
Power Cord
Cord Retainer
Cord Retainer Screw
Handle Screw
Handle Housing
Carbon Brush

1
2
1
3
1
1
1
2
3
1
2

*	Parts 22, 23, & 28 are available as a set only.
^	Parts 24-27 are available as a set only.
Record Product’s Serial Number Here:
Note:	 If product has no serial number, record month and year of purchase instead.
Note:	 Some parts are listed and shown for illustration purposes only, and are not available
individually as replacement parts.

REV 10a

Page 12

For technical questions, please call 1-800-444-3353.

SKU 92115

12

15

13

26

25

24

23

11

27

22

10

21

9

20

19

28

18

17

8

14

5

7

16

6

4

3

2

1

29

30

31

32

35

33

34

ASSEMBLY DIAGRAM

REV 06f, 10a

SKU 92115

For technical questions, please call 1-800-444-3353.

Page 13

LIMITED 90 DAY WARRANTY
Harbor Freight Tools Co. makes every
effort to assure that its products meet
high quality and durability standards, and
warrants to the original purchaser that this
product is free from defects in materials and
workmanship for the period of 90 days from
the date of purchase. This warranty does not
apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents,
repairs or alterations outside our facilities,
criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We
shall in no event be liable for death, injuries
to persons or property, or for incidental,
contingent, special or consequential damages
arising from the use of our product. Some
states do not allow the exclusion or limitation
of incidental or consequential damages,
so the above limitation of exclusion may
not apply to you. This warranty is
expressly in lieu of all other
warranties, express or implied,
including the warranties of
merchantability and fitness.

To take advantage of this warranty,
the product or part must be returned to us
with transportation charges prepaid. Proof
of purchase date and an explanation of the
complaint must accompany the merchandise.
If our inspection verifies the defect, we
will either repair or replace the product at
our election or we may elect to refund the
purchase price if we cannot readily and
quickly provide you with a replacement. We
will return repaired products at our expense,
but if we determine there is no defect, or that
the defect resulted from causes not within the
scope of our warranty, then you must bear the
cost of returning the product.
This warranty gives you specific legal
rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009
Camarillo, CA 93011 • (800) 444-3353

REV 10a

Page 14

For technical questions, please call 1-800-444-3353.

SKU 92115



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.0-c321 44.398116, Tue Aug 04 2009 14:24:39
Instance ID                     : uuid:ad182545-ee68-4b40-a69a-461b770ec22a
Document ID                     : adobe:docid:indd:d3235a62-7587-11df-a4c6-c4e92c328b66
Rendition Class                 : proof:pdf
Derived From Instance ID        : d3235a61-7587-11df-a4c6-c4e92c328b66
Derived From Document ID        : adobe:docid:indd:2b326897-7577-11df-a4c6-c4e92c328b66
Create Date                     : 2010:06:11 11:33:59-07:00
Modify Date                     : 2010:06:11 11:34:20-07:00
Metadata Date                   : 2010:06:11 11:34:20-07:00
Creator Tool                    : Adobe InDesign CS3 (5.0.4)
Format                          : application/pdf
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
Page Count                      : 14
Creator                         : Adobe InDesign CS3 (5.0.4)
EXIF Metadata provided by EXIF.tools

Navigation menu