Chief Manufacturing Jhs Series Users Manual INSTALLATION INSTRUCTIONS
JHS Series to the manual 1308b0b3-04a7-4523-bb12-97c0a0f05e1c
2015-02-05
: Chief-Manufacturing Chief-Manufacturing-Jhs-Series-Users-Manual-533926 chief-manufacturing-jhs-series-users-manual-533926 chief-manufacturing pdf
Open the PDF directly: View PDF .
Page Count: 6
Download | |
Open PDF In Browser | View PDF |
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d´installation Direct Attach Ceiling Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description JHS SERIES JHS SERIES Installation Instructions DISCLAIMER CAUTION: A CAUTION alerts you to the possibility of Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided. WARNING: Failure to provide adequate structural strength Chief® and Centris™ are registered trademarks of Milestone AV Technologies, Inc. All rights reserved. for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. IMPORTANT WARNINGS AND CAUTIONS! WARNING: Exceeding the weight capacity of the mount can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of the mount and all attached components does not exceed 75lbs (34.02kg). WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. DIMENSIONS 31.8 R1.25 1-1/2" NPS UP-DOWN TILT +/- 15° LEFT-RIGHT SWIVEL +/- 75° MEASUREMENTS IN: [MILLIMETERS] INCHES 100 mm VESA PATTERN 167.3 6.59 91.1 3.59 C/L OF VESA PATTERN 152.4 6.00 2 128.3 5.05 Installation Instructions JHS SERIES LEGEND Tighten Fastener Phillips Screwdriver Apretar elemento de fijación Destornillador Phillips Befestigungsteil festziehen Kreuzschlitzschraubendreher Apertar fixador Chave de fendas Phillips Serrare il fissaggio Cacciavite a stella Bevestiging vastdraaien Kruiskopschroevendraaier Serrez les fixations Tournevis à pointe cruciforme Loosen Fastener Hex-Head Wrench Aflojar elemento de fijación Llave de cabeza hexagonal Befestigungsteil lösen Sechskantschlüssel Desapertar fixador Chave de cabeça sextavada Allentare il fissaggio Chiave esagonale Bevestiging losdraaien Zeskantsleutel Desserrez les fixations Clé à tête hexagonale TOOLS REQUIRED FOR INSTALLATION AND PARTS 3/16" (provided) 5/32" (provided) A (1) I/M B (2) 5/16-18 x 3/8" x1 Interface Bracket Kit (including hardware) x1 3 JHS SERIES Installation Instructions INSTALLATION Display Installation Mount Installation 1. IMPORTANT ! : The following installation instructions assume that a 1-1/2" NPT pipe has been properly installed and is in place. 1. 2. Determine mounting pattern on display. WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer! Thread mount (A) onto 1-1/2" NPT pipe until hand tight. Adjust mount (A) position until Centris cup is facing the desired position of the display. (See Figure 1) WARNING: IMPROPER INSTALLATION CAN LEAD TO ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw length must not exceed the depth of threaded mounting insert in display. 1-1/2" NPT Pipe 1 WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket. Centris Cup NOTE: If the display being installed has a 100x100 VESA (A) mounting pattern, no interface bracket is required and the display can be mounted directly to the Centris cup as outlined below. NOTE: If the display being installed requires an interface bracket, refer to the interface bracket installation instructions. WARNING: IMPROPER INSTALLATION CAN LEAD TO Figure 1 3. DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes. Ensure that screws are not too long. When mount (A) is properly positioned secure mount (A) to 1-1/2" NPT pipe by installing and tightening 5/16-18 x 3/8" set screw (B) using 3/16" hex wrench. (See Figure 2) NOTE: If mount is being used to couple two pipes, use both set screws when securing mount (A) to pipes. WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of Centris cup! (B) x 1 (A) (B) x 1 1. Start two M4 x 8mm Phillips pan head screws (included in hardware kit) into upper mounting holes in display back. (See Figure 3) NOTE: Leave at least 1/8" of each screw protruding out back 2 2 (A) Figure 2 4 of display. Installation Instructions JHS SERIES Adjustments To adjust display Roll, Pitch, and YAW tension: 1. 2. 3. 4. 5. 6. 1 Disconnect all wires and cable from the display. Remove two Lower screws securing display to Centris cup. Loosen two Upper screws securing display. Lift display upward and away from mount. Using a hex head wrench turn the tension adjustment screw clockwise to increase tension, or counter-clockwise to decrease tension. (See Figure 5) Re-install display. x2 Figure 3 2. Align two screws in display back with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes. (See Figure 4) 3. Install two more of the same screws through lower mounting holes in Centris cup and into display back. (See Figure 4) 4. Tighten all hardware. 5. Route cables and wires to display. 2 Figure 5 3 4 x2 Figure 4 5 JHS SERIES Installation Instructions USA/International Europe Chief Manufacturing, a division of Milestone AV Technologies Asia Pacific 8805-000220 Rev A 2008 Milestone AV Technologies www.chiefmfg.com 06/08 A P F A P F A 8401 Eagle Creek Parkway, Savage, MN 55378 800.582.6480 / 952.894.6280 877.894.6918 / 952.894.6918 Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands +31 (0)40 2668620 +31 (0)40 2668615 Room 24F, Block D, Lily YinDu International Building LuoGang, BuJi Town, Shenzhen, CHINA. P +86-755-8996 9226 F +86-755-8996 9217
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.0-c320 44.284297, Sun Apr 15 2007 17:19:00 Create Date : 2008:06:26 10:56:16-06:00 Modify Date : 2008:06:26 10:58:14-05:00 Metadata Date : 2008:06:26 10:58:14-05:00 Producer : PDF-XChange 3.50.0099 (Windows Server 2003 x64) Keywords : 8805-000220, Rev A, 6-08, JHS-210, JHS-V Format : application/pdf Title : JHS SERIES INSTALLATION INSTRUCTIONS Creator : Subject : 8805-000220, Rev A, 6-08, JHS-210, JHS-V Document ID : uuid:afa1e0e5-8500-453a-8529-87fd1df24529 Instance ID : uuid:dfc1fea4-0a25-43f8-afe7-93709913aef1 Page Count : 6 Warning : [Minor] Ignored duplicate Info dictionaryEXIF Metadata provided by EXIF.tools