Chief Manufacturing Ventilation Hood Pac510 Users Manual 515 520 INSTALLATION INSTRUCTIONS

PAC510 to the manual a4fdf5cd-140f-4bca-9243-e77555c52910

: Chief-Manufacturing Chief-Manufacturing-Ventilation-Hood-Pac510-Users-Manual-536649 chief-manufacturing-ventilation-hood-pac510-users-manual-536649 chief-manufacturing pdf

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

INSTALLATION INSTRUCTIONS
Istruzioni di installazione
Installatie-instructies
Instructions d´installation

Instrucciones de instalación
Installationsanleitung
Instruções de Instalação

PAC520
(Pre-Drywall)

PAC510
(Post-Drywall)

PAC515
(Pre-Drywall)

IN WALL ACCESSORY BOX
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description

PAC 510, 515, 520

PAC 510, 515, 520

Installation Instructions

DISCLAIMER
CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.

WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

CAUTION: This equipment must be installed and
assembled by qualified service personnel in accordance with
local building codes.

WARNING: Failure to provide adequate structural strength

IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.

2

for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support the combined weight of the box and all
equipment not to exceed 10lbs (4.5kg).

Installation Instructions

PAC 510, 515, 520

LEGEND
Tighten Fastener

Pencil Mark

Apretar elemento de fijación

Marcar con lápiz

Befestigungsteil festziehen

Stiftmarkierung

Apertar fixador

Marcar com lápis

Serrare il fissaggio

Segno a matita

Bevestiging vastdraaien

Potloodmerkteken

Serrez les fixations

Marquage au crayon

Loosen Fastener

Drill Hole

Aflojar elemento de fijación

Perforar

Befestigungsteil lösen

Bohrloch

Desapertar fixador

Fazer furo

Allentare il fissaggio

Praticare un foro

Bevestiging losdraaien

Gat boren

Desserrez les fixations

Percez un trou

Phillips Screwdriver

Adjust

Destornillador Phillips

Ajustar

Kreuzschlitzschraubendreher

Einstellen

Chave de fendas Phillips

Ajustar

Cacciavite a stella

Regolare

Kruiskopschroevendraaier

Afstellen

Tournevis à pointe cruciforme

Ajuster

Open-Ended Wrench

Remove

Llave de boca

Quitar

Gabelschlüssel

Entfernen

Chave de bocas

Remover

Chiave a punte aperte

Rimuovere

Steeksleutel

Verwijderen

Clé à fourche

Retirez

By Hand

Optional

A mano

Opcional

Von Hand

Optional

Com a mão

Opcional

A mano

Opzionale

Met de hand

Optie

À la main

En option

Hex-Head Wrench

Security Wrench

Llave de cabeza hexagonal

Llave de seguridad

Sechskantschlüssel

Sicherheitsschlüssel

Chave de cabeça sextavada

Chave de segurança

Chiave esagonale

Chiave di sicurezza

Zeskantsleutel

Veiligheidssleutel

Clé à tête hexagonale

Clé de sécurité

3

PAC 510, 515, 520

Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

3/16"

PARTS
Grounding screw and washer installed at factory
(See figure 4 on page 7)
J (2) (A1, A2, A3)
#10

H (2) (A1, A2, A3)
10-32 x 3/8"

Earthing symbol IEC 60418 No. 5019
affixed adjacent to grounding terminal.

A1 (1)
PAC-510

2

2

C (4) (A1, A2, A3)
1/4" x 2"

(G) M4 Allen Head Drill Bit (included but not shown)

4

1
2

1

1

B (4) (A1, A2, A3)
1/4"

A3 (1)
PAC-520

A2 (1)
PAC-515

F (6) (A1, A2, A3)
D (6) (A1, A2, A3)
M4 x 40mm

E (8) (A1, A2)
1/8-18 x 3/4"

Installation Instructions

PAC 510, 515, 520

INSTALLATION

mounting surfaces is free of electrical wires and cables
before cutting, drilling, or installing fasteners.

The PAC-510 is intended for use in installations where an
existing finshed (drywalled) wall is present, and includes
flanged edges to cover the cutout in wall. The PAC-515 and
PAC-520 are intended for use in installations where the wall
surface has not been finished and the structure (studs) is
exposed. The PAC-515, and PAC-520 require the wall be
finished around the opening of the box after the box has been
installed.

WARNING: IMPROPER INSTALLATION CAN RESULT
DEATH OR SERIOUS PERSONAL INJURY! This accessory
should be installed by qualified personnel.

WARNING: EXPLOSION AND FIRE HAZARD!
CUTTING OR DRILLING INTO GAS PLUMBING CAN
CAUSE DEATH OR SERIOUS PERSONAL INJURY!
ALWAYS make certain area behind mounting surfaces
is free of gas, water, waste, or any other plumbing
before cutting, drilling, or installing fasteners.
2.

Using a stud sensor, locate and mark studs.

3.

Center and level housing between marked studs.

4.

Using housing as a template, draw pencil line completely
around housing.

PAC-510 Site Preparation

NOTE: Housing is designed to fit between and directly against

Locate and Prepare Mounting Site
1.

two adjacent wall studs.

Identify a suitable wall location for the accessory.

IMPORTANT ! : The PAC-510, 515, AND 520 are
designed for in-wall installation between two wood or
steel studs, 16" on center. Inadequate space will remain
on each side between studs for electrical wires/cables,
plumbing, ductwork, or insulation. Locate accordingly!

5. Using a measuring tool, measure the marked area
and compare to the dimensions shown in figure1
below. If measurements match continue to step 6 if
not adjust markings to match dimensions in figure 1
below.
6. Cut drywall on outside edge of line and remove.

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL WIRES OR
CABLES CAN CAUSE DEATH OR SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind

Figure 1

5

PAC 510, 515, 520

Installation Instructions

Accessory Box Installation
1.

Insert accessory box into opening, if installing PAC510 or
PAC515, or position PAC520 in desired mounting location.

WARNING: ELECTRICAL SHOCK HAZARD! CUTTING
OR DRILLING INTO ELECTRICAL WIRES OR
CABLES CAN CAUSE DEATH OR SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind
mounting surfaces is free of electrical wires and cables
before cutting, drilling, or installing fasteners.
2.

Secure accessory box to studs by:

WOOD STUD:
1.

drill four 3/16" dia. pilot holes in studs at mounting
holes.

2.

install four M4 x 40mm Allen head connector screws
into pilot holes using an M4 Allen head drill bit
(provided).

STEEL STUD:
1.

drill four 3/16" dia. pilot holes in studs at mounting
holes.

2.

install four 1/4" countersunk finishing washers and
four 1/4" x 2" Phillips flat head self drilling screws
into pilot holes.

NOTE: When installing PAC520 in configuration B the quantity
of hardware changes to three for both wood and steel
stud installations.

Figure 2

x3
(3/16" dia. Pilot)
(Steel Stud Only)

x4
(3/16" dia. Pilot)
(Steel Stud Only)
(C) x4

(C) x4

(C) x4

(C) x4
(Steel Stud Only)

(B) x4
(Steel Stud Only)

(B) x4
(Steel Stud Only)
(C) x4
(Steel Stud Only)

PAC510 and PAC515

PAC520

Figure 3

6

(C) x4
(Steel Stud Only)
(B) x4
(Steel Stud Only)

Installation Instructions

PAC 510, 515, 520

DANGER: IMPROPER WIRING CAN LEAD TO DEATH
OR SEVERE PERSONAL INJURY! Grounding must be
installed by qualified personnel using a UL Recognized No.
12AWG Green and Yellow grounding wire connected to
grounding lug on mount.

PAC-510

1

Installing Accessories
2

Accessories can be mountied directly to the PAC510, PAC515,
and PAC520 by using the mounting screws provided and the
mounting holes intergrated into the box.
To mount an accessory:
1.

Identify area within accessory box that accessory is to be
mounted.

2.

Align the mounting holes in accessory with mounting holes
in box.

3.

Secure accessory to box using Phillips screwdriver and as
many 1/8-18 x 3/4" mounting screws (8 provided) as
required.

Typical
1
PAC-515
2

NOTE: The top and bottom slots in the side flanges of PAC510
are designed to hall at the center of the studs on 16"
centers. When installing a mount over the top of
PAC510, align mounting holes in mount with top and
bottom slots in side flanges and secure using hardware
specified in the Installation Instructions provided with
the mount.

PAC-520

1
2

Grounding lug location

Figure 4

(E) (8 provided)

Figure 5

7

PAC 510, 515, 520

Installation Instructions

USA/International

Europe

Asia Pacific
8807-000054 RevA
2007 Chief Manufacturing
www.chiefmfg.com
04/07

A
P
F
A
P
F
A

8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
31 (0)20 5708923
31 (0)20 5708989
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112

P +86-755-8996 9226 ; 8996 9236 ; 8996 9220
F +86-755-8996 9217



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-702
Create Date                     : 2007:07:19 14:09:05-06:00
Modify Date                     : 2007:07:27 14:25:58-05:00
Metadata Date                   : 2007:07:27 14:25:58-05:00
Producer                        : PDF-XChange 3.50.0099 (Windows Server 2003 x64)
Keywords                        : 8807-000054, Rev A, PAC510, PAC515, PAC520
Format                          : application/pdf
Title                           : PAC510-515-520 INSTALLATION INSTRUCTIONS
Creator                         : .
Subject                         : 8807-000054, Rev A, PAC510, PAC515, PAC520
Document ID                     : uuid:b85b602a-f535-4e5f-9d10-8b696abc7b93
Instance ID                     : uuid:5be0ae94-179e-432d-bc8f-cccb860e7e0c
Page Count                      : 8
Warning                         : [Minor] Ignored duplicate Info dictionary

EXIF Metadata provided by EXIF.tools