China Electric Manufacture HH-R002 Ceiling Fan Remote Controller User Manual NEW EN28r 35T1 2012 05 14

Download:
Mirror Download [FCC.gov]
Document ID	2083976
Application ID	73uQbZmUilYZnAfJfz0gJg==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	20.03kB (250409 bits)
Date Submitted	2013-09-27 00:00:00
Date Available	2013-09-27 00:00:00
Creation Date	2012-05-14 07:22:52
Producing Software	Corel PDF Engine Version 3.0.0.667
Document Lastmod	0000-00-00 00:00:00
Document Title	NEW EN28r+35T1(2012.05.14).cdr
Document Creator	CorelDRAW
Document Author:	Administrator

EN35T28R1205DIM
Remote controller
GENERAL INFORMATION
This remote controller is designed to separately control your ceiling fan speed and light brightness.
There are four buttons (HI, MED, LOW, OFF) to control the speed of the fan and off.
The light dimmer button will control the light brightness dimmer and off.
The red indicator on the transmitter will light when one of the five buttons is pressed.
INSTRUCTION OF INSTALLATION AND OPERATION
1.SETTING THE CODES
This unit has 16 different code combinations. To set the codes, perform the following steps:
A. Setting the codes on the transmitter:
a. Remove battery cover. Press firmly on the arrow and slide battery cover off.
b. Slide code switches to your choice of up or down position. Factory setting is all up. Do not use this position. Use a
small screwdriver or ball point pen to slide firmly up or down (Figure 1).
B. Setting the codes on the receiver:
a. Slide code switches to the same position as set on your transmitter (Figure 2)
b. Replace battery cover on the transmitter.
ON
ON
RECEIVER
ANT
LEARN
INPUT
CODE
SWITCHES
CODE
SWITCHES
(FIG.1)
FC C ID : L3 HFA N3 5T 1
(FIG.2)
OUTPUT
COM
FAN
LIGHT
CAUTION: Ceiling Angle Shall Not Exceed 30 Degrees,
For Mounting Controller, Model FAN28R-190WA
CONNECT
TO
Green fan wire ....Bare supply wire
Red receiver wire(AC IN L) ....Red or Black supply wire
White receiver wire(AC IN N) ....White supply wire
White receiver wire(TO MOTOR N) ....White fan wire
Black receiver wire(TO MOTOR L) ....Black fan wire
Blue receiver wire(FOR LIGHT) ....Blue light wire
Use wire connecting nuts supplied with the fan
FROM POWER SOURCE
AC 110~120 VOLT 60Hz
3.5AMPS.
(FIG.3)
WHITE
RECEIVER
RED
ANT
ACL
ACN
INPUT
(FIG.4)
LIGHT
FAN
COM
CANOPY
OUTPUT
RECEIVER
WHITE
BLUE
BLACK
BLACK
WHITE
ANTENNA PUT AT OUTSIDE
OF CANOPY BOX CAN GET
MORE OPERATION
DISTANCE
BLUE
WIRE NUT
Use wire connecting nuts
supplied with the remote
controller.
ON
ACL
A. Safety precautions:
WARNING: HIGH VOLTAGE! Disconnect power by
removing fuse or switching off circuit breaker.
Do not use with solid state fans.
Electrical wire must meet all local and national
electrical code requirements.
Supply for fan must be 110/120 volt, 60Hz. Maximum
fan motor amps: 1.0, Maximum light watts: 190
incandescent or ballast.
Otherwise power can cause serious injury or death.
B. Installing receiver in fan:
a. Remove power from the circuit.
b. Remove ceiling fan canopy from the mounting
bracket.
c. Disconnect existing wiring between ceiling fan and
Supply in electrical junction box.
d. Make connections as follows, using the wire nuts
supplied:
ACN
ON
2.INSTALLING RECEIVER IN CEILING FAN
CANOPY
LIGHT MUST BE KEPT AT THE ON POSITION
FA N M U S T B E K E P T AT T H E H I G H S P E E D
EN35T28R1205DIM
If other fans or supply wires are different color, have this unit installed by qualified licensed electrician.
e. Push all connected wires up into junction box.
f. Lay the brown antenna wire on top of the receiver, and put the receiver into the mounting bracket.
g. Reinstall the canopy on the mounting bracket.
h. Restore power.
3. OPERATING TRANSMITTER:
A. Install 12 volt battery(not included). (To prevent damage to transmitter, remove the battery if not used for a long time).
B. Store the transmitter away from excessive heat or humidity.
C. This remote control unit is equipped with 16 code combinations. In order to prevent possible interference from or to
other remote units such as garage door openers, car alarm or security system. If you find that your fan and light kit go
on and off without using your remote control, simply change the code combination in your transmitter and receiver.
D. Operating the buttons on the panel of the transmitter.
HI key -for fan high speed.
MED key-for fan medium speed.
LOW key-for fan low speed.
OFF key-for fan off.
LIGHT/DIMMER key-for light brightness and off.
The light function is controlled by pressing the LIGHT/DIMMER key down to increase or decrease light.
Tap key quickly to turn light off or on.
Keep pressing the button in excess of 0.7 second and it becomes a dimmer, the light varies cyclically in 0.8 second.
The receiver can remember the last status of the light brightness when the light was switched, so that it can
resume to adjust the light brightness.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
23A 12V
LEARN
OPERATION DISTANCE 20 FEET
FCC ID: L3HFAN35T1
MODEL:
FAN-35T1
Optional Wall Mounting for Transmitter Holder
Place in accessible area of your home, and screw the
transmitter holder into wall using the two screws
provided, slide hand unit into holder.
TRANSMITTER
4. TROUBLE SHOOTING GUIDE
1. Fails to operate
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
f. Code set at exact same positions in both transmitter and receiver ?
2. Won ' t operate at distance
If transmitter operates fan/light kit when up close, but not at 20 feet away.
Try placing the brown antenna wire higher, up through ceiling/outside the junction box.
NOTICE !
Your ceiling fan and light kit assembly must meet the following requirements:
1. Do not use with solid state fans.
2. Electrical rating: 120v 60Hz 3.5A
MAX. Motor amps: 1.0
MAX. Light watts: 190-(incandescent or ballast)
WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
NOTE:
Changes or Modifications not expressly approved by the party responsible could void
the user’s authority to operate this device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
XMP Toolkit                     : 3.1-702
Creation Date--Text             : 
Producer                        : Corel PDF Engine Version 3.0.0.667
Mod Date--Text                  : 
Format                          : application/pdf
Creator                         : Administrator
Title                           : NEW EN28r+35T1(2012.05.14).cdr
Creator Tool                    : CorelDRAW
Modify Date                     : 2013:09:05 08:56:21+08:00
Metadata Date                   : 2013:09:05 08:56:21+08:00
Document ID                     : uuid:59b38bac-b40b-44b4-b8bf-cbccd4d37e74
Instance ID                     : uuid:dc6d9e5d-c3fb-414b-b2cb-2274befeae7c
Page Count                      : 3
Create Date                     : D:20120514072252
Author                          : Administrator

EXIF Metadata provided by EXIF.tools