China Etech Groups FD4003-D RECEIVER User Manual
China Etech Groups Ltd. RECEIVER
User Manual
Size: mm,印在正反两面,中间折 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept Product Specification for 2.4G Wireless Mouse Wireless Frequency: 2402MHz-2480MHz Work Frequency: 64 hopping Rated work voltage: 1.5V Rated work electric current: Battery: 15mA AA×1PCS Locomotive perceptive system: Laser Resolution: Default CPI value(800-1600) USB Port version USB1.1/2.0 *The spec above decribtion, we will not inform you if any changes. Warning: Any change or modification not expressly approved by the party responsible for compliance could avoid the user ’s authority to operate the equipment any interference received, including interference that may cause undesired operation. Exclusive Function: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. LM-001 2.4G wireless optical mouse Feature: Reset: It has the ID memory function automatical, please reconnect ID if you lost the memory code. 1,Low battery remind function When you using the mouse, if the low-power indication light flickers, it shows the batteries are drains up to empty, then you should change a new battery at once High magnetic field and libration will lead to these two distinguish code disappear. you need reset it. Don’t use old battery.Only valid for alkaline dry battery,other battery will effect the use of mouse. 2,Sleeping function The mouse will power off by itself if you don’t use it for about 8 2.4G frequency,digital cordless with distance up to ten meters minutes Just press any key or scroll the wheel to wake up the PAN3204 chipset,high-precision and high- stabilization mouse when it is sleeping. Please turn off it when you go outside Default CPI value(800-1600) or don’t use it for a long time. Low power remind function,change the battery in time Turn off it if you don’t use it for a long time,it will avoid to 1,Reconnect the receiver 2,Press and hold on to and the scroll wheel of the mouse together for about 15 seconds .。 3,You are now ready to the wireless world. Operation Note: canker accessories of mouse. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. This limits are designed to provide reasonable 3, CPI adjusting function protection against harmful interference in a residential installation. This equipment 1,Take the mouse and receiver from the packing. Referring to pictrue one. generates radio frequency, if not installed and used according to the instructions, it may 2,Open the battery cover,put into 1 AA battery(Pay attention to the battery polarity) cause harmful interference to radio communications. However, there is no guarantee that Referring to pictrue two. Default CPI value is 1200. 4,Built-in receiver interference will not occur in a particular installation. If this equipment does cause harmful It has a super Nano receiver,you can put it into the USB connect interference to radio or television reception, which can be determined by turning the of PC or notebook, it will not infect your computer at all. If you equipment off and on, the user is encouraged to try to correct the interference by one or just want to take the mouse outside, you can also put it into the more of the following measure, bottom of the mouse. * Reorient or relocate the receiving antenna is connected *Consult with the dealer or an experienced radio/TV technician for help This mouse uses laser light as transfer checking, it comply with correlative safe prescript, please do not look into the bottom of the mouse directly. Regards to 2.4GHZ wireless data transfer, the distance is 10 meters. The distance will be less if there are obstacles or blockage. The unsmooth or anti-optical surfaces will infect the function. * Increase the separation between the equipment and receiver * Connect the equipment into an outlet on a circuit different from that to which the receiver Remark: 3, Pull On-Off the key to ON. The led will flash a few seconds. Referring to pictrue three. 4,Plug the mini wireless receiver (Nano) into the USB port. Referring to pictrue four 5,Now you can use it and enjoy it.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 1 Language : zh-CN Tagged PDF : Yes Author : yhp Creator : Microsoft® Office Word 2007 Create Date : 2012:12:06 14:19:31 Modify Date : 2012:12:06 14:19:31 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools