Chromagic Technologies HAN02 In-Wall Switch Module User Manual HAN02 UserManual 2011 12 02

Download:
Mirror Download [FCC.gov]
Document ID	1594065
Application ID	slQJ+iv+NNyDZ54HQFoGVQ==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.96kB (61952 bits)
Date Submitted	2011-12-03 00:00:00
Date Available	2011-12-08 00:00:00
Creation Date	2011-12-02 11:21:13
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2011-12-02 11:21:13
Document Title	Microsoft Word - HAN02_UserManual-2011-12-02.DOC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	levenhuang

Auto Inclusion
HAN02 IN-WALL SWITCH MODULE
The function of auto inclusion will be executed as long as the module does not have
node ID when the first power is applied.
TM
This in-wall switch module is a transceiver which is a Z-Wave enabled device and
is fully compatible with any Z-WaveTM enabled network. Z-WaveTM enabled devices
displaying the Z-WaveTM logo can also be used with it regardless of the manufacturer,
and ours can also be used in other manufacturer’s Z-WaveTM enabled networks.
Remote On/Off control of the connected load is possible with other manufacturer’s
Wireless Controller.
After node ID has been linked, auto inclusion will run automatically after the
execution of exclusion/reset is successful.
Note: Auto inclusion lasts for 4 minute or until the execution of inclusion is completed
during which the node information of explorer frame will be emitted once every 5
seconds. Unlike “inclusion” function as shown in the table below, the execution of
auto inclusion is free from pressing the On/Off button on the module.
This in-wall switch module is able to detect overload wattage of connected
non-dimmable lights or appliances. When detecting overload state, the module will be
disabled and its On/Off button will be lockout of which LED will flash quickly.
However, disconnect and re-connect the wiring of the module will reset its overload
condition to normal status.
Function
No node ID
Adding to Z-WaveTM Network
Inclusion
In the front casing, there is an On/Off button with LED indicator which is used to carry
out inclusion, exclusion, reset or association. Toggle On/Off button between On and
Off. When first power is applied, its LED flashes on and off alternately at 2-second
intervals. It implies that it has not been assigned a node ID and cannot work with
Z-Wave
enabled
devices.
Put
Z-WaveTM
Controller
into
inclusion/exclusion/association mode, the module executes the function of auto
inclusion.
On/Off Button
LED Indicator
Exclusion
Description
After power is applied, if the module
does not record a node ID provided by
controller.
1. Have Z-Wave Controller entered
inclusion mode.
2. Pressing On/Off button three times
within 1.5 seconds will enter
inclusion mode or
3. Close and open manual switch input
of S1 or S2 between C three times
within 1.5 seconds at the first 3
minute when the first power is
applied will enter inclusion mode
1.
manual switch input
2.
3.
Have Z-Wave Controller entered
exclusion mode.
Pressing On/Off button three times
within 1.5 seconds will enter
exclusion mode or
close and open manual switch input
of S1 or S2 between C three times
within 1.5 seconds at the first 3
minute when the first power is
applied will enter exclusion mode
Node ID has been excluded
successfully.
LED Indication
2-second on, 2-second off
2-second on, 2-second off
Reset
1.
2.
Pressing On/Off button three times
within 1.5 seconds will enter
inclusion mode, within 1 second,
press On/Off button again until LED
is off or
Close and open manual switch input
of S1 or S2 between C three times
within 1.5 seconds at the first 3
minute when the first power is
applied will enter inclusion mode,
within 1 second, Close manual
switch input of S1 or S2 to C again
until LED is off.
3.
Association
Home ID and node ID will be
cleared and reset to factory default.
1. Have Z-Wave Controller entered
association mode first.
LED Indication
To distinguish what mode the module is in, view from the LED for identification.
State Type
Normal
No node ID
2-second on, 2-second off
Overload
2.
Pressing On/Off button three times
within 1.5 seconds will enter
association mode or
3. close and open manual switch input
of S1 or S2 between C three times
within 1.5 seconds at the first 3
minute when the first power is
applied will enter association mode
LED Indication
Under normal operation, toggle On/Off button between On and
Off. When pressing On, LED lights up, whereas Off, LED is off.
And when manual switch input from open (NO) to short (NC) or
from short (NC) to open (NO) will also trigger the toggle function.
Under normal operation, when the module has not been allocated
a node ID, the LED flashes on and off alternately at 2-second
intervals. By pressing On/Off button, it will stop flashing
temporarily. However, after disconnecting and reconnecting the
wiring of the module, the LED will flash on and off alternately at
2-second intervals.
When overload state occurs while the module is on, the module
will be converted to off right away of which LED flashes on and off
at 0.5-second intervals and on/off button will be lockout.
Overload state can be cleared by disconnecting and reconnecting
the wiring to the terminal block.
Choosing a Suitable Location
1. Do not locate the module facing direct sunlight, humid or dusty place.
2. The suitable ambient temperature for the module is 0°C~40°C.
3. Do not locate the module where exists combustible substances or any source of
heat, e.g. fires, radiators, boiler etc.
4. After putting it into use, the body of module will become a little bit hot of which
phenomenon is normal.
Including a node ID allocated by Z-Wave Controller means inclusion.
Excluding a node
ID allocated by Z-Wave Controller means exclusion.
Failed or success in including/excluding the node ID can be viewed from the Z-Wave
Controller.
Installation
Note: Please note that it is a must to call for a licensed electrician for installation.
1. Install this module into a wall box of which wiring connection is shown hereunder:
2. After wiring connection is completed, execute inclusion and association process
between the module and remote controller.
3. There are different way to manually turn ON or OFF the module, first way is
using On/Off button, and the function behavior as below
Initial state
ON
OFF
action
press and release the On/Off button
press and release the On/Off button
Programming
final state
OFF
ON
1. Basic Command Class / Binary Switch Command Class
1-1 BASIC_GET / BINARY_SWITCH_GET
Upon receipt of the following commands from a Z-Wave device, the module will
send Basic Report Command / Binary Switch Report Command, reporting its
On/Off state to the Controller.
Second way is for manual switch input S1,S2, C which connect to external
binary switch and the module had been set to “binary switch mode” , the function
behavior as below
Initial state
action
final state
ON
when S1 is open to C, Close S1 to C
OFF
OFF
when S1 is close to C, open S1 from C
ON
ON
OFF
when S2 is open to C, Close S2 to C
when S2 is close to C, open S2 from C
Basic Get Command: [Command Class Basic, Basic Get]
Basic Report Command:
Report OFF: [Command Class Basic, Basic Report, Value = 0x00(0)]
Report ON:[Command Class Basic, Basic Report, Value = 0xFF(255)]
OFF
ON
Binary Switch Get Command:[Command Class Switch Binary, Switch
Binary Get]
Basic Report Command:
Report OFF:[Command Class Switch Binary, Basic Report, Value
=0x00(0)]
Report ON:[Command Class Switch Binary, Basic Report, Value =
0xFF(255)]
for manual switch input S1,S2, C which connect to external toggle switch and
the module had been set to “toggle switch mode” , the function behavior as below
Initial state
ON
OFF
action
Close S1 to C and release S1 to C
Close S1 to C and release S1 to C
final state
OFF
ON
ON
OFF
Close S2 to C and release S2 to C
Close S2 to C and release S2 to C
OFF
ON
1-2 BASIC_SET / SWITCH_BINARY_SET
Upon receipt of the following commands from a Z-Wave device, the load
connected to the module and module’s LED will turn on or off.
[Command Class Basic, Basic Set, Value = 0xFF(255)]: the load attached
to the module turns on and LED on.
[Command Class Basic, Basic Set, Value = 0x00(0)]: the load attached to
the module turns off and LED off.
Change manual switch input mode
Press On/Off Button over 5 second and no longer than 8 second, if success the led will
flash 3 times and the manual switch input mode will change from “binary switch mode”
to “toggle switch mode” or from “toggle switch mode” to “binary switch mode”.
[Command Class Switch Binary, Switch Binary Set, Value = 0xFF(255)]:
the load attached to the module turns on and LED on.
[Command Class Switch Binary, Switch Binary Set, Value = 0x00(0)]: the
load attached to the module turns off and LED off.
Command Classes
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The module supports Command Classes including as follow:
* COMMAND_CLASS_SWITCH_BINARY
* COMMAND_CLASS_BASIC
* COMMAND_CLASS_MANUFACTURER_SPECIFIC
* COMMAND_CLASS_VERSION
* COMMAND_CLASS_SWITCH_ALL
Troubleshooting
Symptom
The module not working
and LED off
Cause of Failure
1. Improper wiring
connection
2. The module break
down
The module LED
Check if the load
illuminating, but cannot
connected to the module
control the ON/OFF
has its own ON/OFF
Switch of the load attached switch
The module LED
1. Not carry out
illuminating, but the
association
Detector cannot control
2. Same frequency
the module
interference
Recommendation
1. Check power connections
2. Don’t open up the module and
send it for repair.
Set the ON/OFF switch of the
load connected to ON
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
1. Carry out association
2. Wait for a while to re-try
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
Specification
Operating Voltage
Maximum Load
Range
Operating Temperature
Frequency Range
100~120Vac/60Hz(US) / 220~240Vac/50Hz (EU)
1000W for incandescent or 320W for fluorescent @230V/50Hz
Minimum 70 m line of sight
0°C ~ 40°C
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
WARNING:
Do not dispose of electrical appliances as unsorted municipal waste, use separate
collection facilities.
908.42 MHz (US) / 868.42 MHz (EU)/921.42MHz(AU)
** Specifications are subject to change and improvement without notice.
Contact your local government for information regarding the collection systems
available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances
can leak into the groundwater and get into the food chain, damaging your health and
well-being.
When replacing old appliances with new once, the retailer is legally obligated to take
back your old appliance for disposal at least for free of charge.
FCC ID: ZGXHAN02

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : levenhuang
Create Date                     : 2011:12:02 11:21:13+08:00
Modify Date                     : 2011:12:02 11:21:13+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - HAN02_UserManual-2011-12-02.DOC
Creator                         : levenhuang
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:730d0d7f-af9a-40f7-bd83-aa59ec93880a
Instance ID                     : uuid:cbd66901-8fc6-4b95-950d-35d7cfd7fcd3
Page Count                      : 4

EXIF Metadata provided by EXIF.tools