Chungear Co 9303 Fan-Light Remote Controller (Transmitter) User Manual CS8K BL JY199

Download:
Mirror Download [FCC.gov]
Document ID	476621
Application ID	zxlvK9CIG2jECJ9jMVLJPQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.62kB (407754 bits)
Date Submitted	2004-10-06 00:00:00
Date Available	2004-10-06 00:00:00
Creation Date	2004-09-07 17:51:13
Producing Software	Acrobat PDFWriter 5.0 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	CS8K-BL+JY199說明書.doc
Document Creator	CS8K-BL+JY199說明書 - Microsoft Word
Document Author:	Monica_chang

FCC ID. KUJ9303
CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED
AND LIGHT KIT (IF ANY) TO ON POSITION BEFORE OPERATING
REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1.Read and save these instructions.
2.Please note that all fixed wiring appliances should be installed by a qualified electrician.
3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall
switch.
4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6.This unit is to be used for the control of ceiling fan and in a AC120V~240V 50Hz power supply only.
7.Do not install in lamp locations or immerse in water. (For indoor use only.)
8.Do not pull on or cut leads shorter.
9.Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place
as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of
children.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “Pull Switch”
after installation.
2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy
comes up to cover the receiver and bracket.
FCC ID. KUJ9303
CODE SWITCH
1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used
for both transmitter and receiver is exactly the same, otherwise remote controller will not work. Please
note the code switch will enable you to operate a second remote controller independently. For example, if
you have two ceiling fans with 2 remote control units, set 2 different codes for each set of
transmitter/receivers. This means you can operate each ceiling fan independently.
2.Your remote control is ready for use after battery installation.
TRANSMITTER
FUNCTIONS OF TRANSMITTER
: Turn on the fan at high speed
: Turn on the fan at medium speed
: Turn on the fan at low speed
: Turn off the ceiling fan.
: Turn on or off the light.
: Press and hold on to dimmer or brighten the light. (Tungsten only)
: Light will be automatically turned off in 3 minutes after this key is pressed
(Delay off).
: Press, then speeds of fan will be turned and changed at random.
Ceiling Fan Remote Control
Wiring Connection
Installation of Transmitter Wall
Mount Holder With Two Screws.
FCC ID. KUJ9303
FEDERAL COMMUNICATIONS COMMISSION
INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user’s
authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 3
Creator                         : CS8K-BL+JY199說明書 - Microsoft Word
Create Date                     : 2004:09:07 17:51:13
Title                           : CS8K-BL+JY199說明書.doc
Author                          : Monica_chang
Producer                        : Acrobat PDFWriter 5.0 for Windows NT

EXIF Metadata provided by EXIF.tools