Chungear Co CE10206 Ceiling Fan Remote Controller (Transmitter) User Manual E01BT S JY326B

Download:
Mirror Download [FCC.gov]
Document ID	2099220
Application ID	6Mt6+9U5mNUkpowfCkklhw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	7.42kB (92719 bits)
Date Submitted	2013-10-22 00:00:00
Date Available	2013-10-22 00:00:00
Creation Date	2013-09-30 15:40:48
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2013-10-22 09:36:50
Document Title	Microsoft Word - E01BT-S JY326B.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	user

CEILING FAN REMOTE CONTROLLER
OPERATION AND INSTALLATION INSTRUCTIONS
(Please keep this instruction pamphlet.)
IMPORTANT
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT
(IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1.Read and save these instructions.
2.Please note that all fixed wiring appliances should be installed by a qualified electrician.
3.The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall
switch.
4.Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5.Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6.This unit is to be used for the control of ceiling fan and in a AC110/120V 60Hz power supply only.
7.Do not install in damp locations or immerse in water. (For indoor use only.)
8.Do not pull on or cut leads shorter.
9.Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place
as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of
children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
1.Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “Light Switch”
after installation.
2.Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy
comes up to cover the receiver and bracket.
CODE SWITCH
1.CODE SWITCH: Codes are set by pushing dip switches up or down. It is imperative that the code used
for both transmitter and receiver is exactly the same, otherwise remote controller will not work. Please
note the code switch will enable you to operate a second remote controller independently. For example, if
you have two ceiling fans with 2 remote control units, set 2 different codes for each set of
transmitter/receivers. This means you can operate each ceiling fan independently.
2.Your remote control is ready for use after battery installation.
TRANSMITTER
FUNCTIONS OF TRANSMITTER
OFF: Turn off the fan.
HI : Turn on the fan at high speed.
MED:Turn on the fan at medium speed
LOW: Turn on the fan at low speed
LIGHT ON/OFF: turn on or off the light.
DIMMER: Press and hold to dim lights.
Ceiling Fan Remote
Control
Wiring Connection
MODEL:E01BT-S
Installation of Transmitter
Wall Mount Holder with
two screws.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority
to operate the equipment.
FCC ID：KUJCE10206
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IC
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
French:
Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositif est
autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2)
l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fonctionnement du dispositif.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un
environnement non contrôlé.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2013:10:22 09:36:50+08:00
Create Date                     : 2013:09:30 15:40:48+08:00
Metadata Date                   : 2013:10:22 09:36:50+08:00
Format                          : application/pdf
Title                           : Microsoft Word - E01BT-S JY326B.doc
Creator                         : user
Document ID                     : uuid:3f0e6ea9-7c7e-4343-acf1-2f0e02ba6bc7
Instance ID                     : uuid:cca7e286-30dd-42c9-be12-f5fe9e04412d
Has XFA                         : No
Page Count                      : 3
Author                          : user

EXIF Metadata provided by EXIF.tools