Chungear Co CE10325 Ceiling Fan Remote Controller (Transmitter) User Manual 206A

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter) 206A

Contents

206A

WALL TRANSMITTEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing wallswitch.4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supply only.7. Do not install in wee locations or immerse in water.8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes placeas this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach ofchildren.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable(rheostat) wall control.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed after installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. Thecanopy comes up to cover the receiver and bracket. (FIG 1, 2 and 3)IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED LIGHT KIT ONPOSTION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
ACTIVATING THE LEARNING PROCESS1. After installation is complete, AC power is turned onand SWITCH is at ON position within 30seconds, press and hold the LEARN button for 3seconds. Fan will turn on at medium speed and light(if installed) will turn on. This confirms that the SMARTSYNC setting is active and ok. (FIG. 4)2. If user cannot finish the setting within the 30 secondstime frame, the main power must be turned off andre-started again. This will reset the unit. Repeat step 1until the LEARNING feature is activated as indicated.LIGHT FUNCTION SELECT SWITCH1. If installed energy light onto ceiling fan, please slide the “light function select switch” to “O”position. If installed tungsten light onto ceiling fan, please slide the “light function selectswitch” to “D” position. (FIG. 4)2. Light load: 190W (Max.) If overload, the receiver will cut off light power automatically. Pleasechange the light load.WALL TRANSMITTER OPERATION (FIG.5)FAN OFF :Turn off the ceiling fan.HI : Turn on the fan at high speed.MED : Turn on the fan at medium speed.LOW : Turn on the fan at low speed.LIGHT : ON/OFF-Turn the light on or off.DIMMER-Press and hold to dim orbrighten light to the desired level and release.(Tungsten only and light function select switch on “D” position.)FIG.5AC POWER ON/OFF SWITCH( ): Before installingwall control, slide to “OFF” position. After installed well, slide to “ON” position and could remote.Installing Wall Control (TRANSMITTER):Remove wall plate, disconnect and remove the toggle switchfrom wall junction box. Using the wire connectors,make the electrical connections to the wall control(transmitter) unit. Carefully push all connected wiresinside wall switch box. Secure wall control unit with2 screws previously removed. Face plate could be clickedonto the transmitter.TRANSMITTERFIG. 4TR206ATR207A
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consultthe dealer or an experienced radio/TV technician for help.CAUTION:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10325This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Navigation menu