Chungear Co CE10410 CEILING FAN REMOTE CONTROLLER (TRANSMITTER) User Manual
Chungear Industrial Co Ltd CEILING FAN REMOTE CONTROLLER (TRANSMITTER)
User Manual
2H 4H 8H
H
a
r
b
o
r
B
r
e
e
z
e
H
a
r
b
o
r
B
r
e
e
z
e
Black (hot/power)
Push-on
Connector
White (neutral)
Red
White
White White
Black
Blue Blue
Black
Antenna
Receiver
2H 4H 8H
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
SAFETY INFORMATION
1. Use pull chains to set fan speed to
high and light on.
2. Turn off circuit breakers and wall
switch to the fan.
DANGER: Failure to disconnect
power supply prior to installation
may result in serious injury or
death.
3. Lower the canopy of the previously
assembled fan and insert receiver.
Note: If installing the remote in a new
fan, insert the receiver in the mounting
bracket before wiring the fan. Wire the
fan according to these instructions.
Then, continue fan assembly as
directed in the fan’s instruction
manual.
• Connect the Red wire with red label from the receiver to the Black
(hot/power) supply wire.
• Connect the White wire with red label from the receiver to the White
(neutral) supply wire.
REMOTE WITH TIMER
ITEM #0745359
MODEL #41235
Serial Number
Purchase Date
ATTACH YOUR RECEIPT HERE
Harbor Breeze® is a registered trademark
of LF, LLC. All rights reserved.
XXXXXXX 9130 • 101315
Read instructions completely before installing wall control.
CAUTION: Do not install in damp locations. For indoor use only.
CAUTION: Do not use with fans that have integrated remote controls.
CAUTION: Be sure the outlet box is properly grounded or that a green or bare (ground) wire is present.
CAUTION: This unit is intended to control a ceiling fan with electrical source of AC 110/120V, 60Hz.
CAUTION: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
WARNING: If the color of the household supply wires is different than what is referred to in the instructions below, a professional electrician should determine
proper wiring.
Printed in China
3
4
1
2
5
6
7
8
1
4. Secure all wiring connections with wire
connectors according to diagram and
these steps:
• Connect the Blue wire with white
label from the receiver to the Blue
fan wire.
• Connect the Black wire with white
label from the receiver to the Black
fan wire.
• Connect the White wire with white label
from the receiver to the White fan wire.
Fan Pull
Chain
Light Pull
Chain
Wall Bracket
Mounting
Screws
Light Control
Home Shield
Delay
Off
Timers
Low
Medium
High
Learn
D/O
Canopy
Receiver
High
LED Indicator
Battery
5. Wrap electrical tape (not included)
around each push-on connector
down to the wire. Then, push wire
connections into the outlet box. Place
the Green and White wire connections
on the opposite side of the outlet
box from the Black and Blue wire
connections.
6. Turn on power supply and wall switch
to the fan.
7. Remove the battery cover from the
back of the remote and install two
AAA batteries. Replace the battery
cover and press the high button to
ensure the LED indicator illuminates
and the fan turns on.
8. If desired, the wall bracket can be
attached to a wall using the mounting
screws from the hardware bag. Slide
small plate over mounting screws,
then rest the remote in the wall
bracket for easy storage.
1. To operate the fan using the remote, press and release the following buttons:
High - Turns fan on high speed.
Medium - Turns fan on medium speed.
Low - Turns fan on low speed.
Fan Off - Turns fan off.
Walk Away Light DelayTM - Tap once will turn fan light off after 1 minute. Note: Light blinks to conrm that Walk
Away Light Delay is active. Press any other button to cancel.
Timer - With fan on, press desired timer button (2, 4 or 8 hour). Fan light (if applicable) blinks to conrm timer is
active. Press fan off to cancel timer.
Home ShieldTM - Press and hold Light and Delay buttons for 3 seconds. Lights cycle on for 5-20 minutes and off for
60 minutes, simulating occupancy. Cycle repeats continuously until any other button is pushed to discontinue Home
Shield mode.
Light Control - Light Control:
Incandescent Bulbs - Press light control to turn lights off and on. Press and hold light control to dim or brighten the
lights.
CFL -Turns the lights on and off. Note: The dimmer function does not work with CFL bulbs.
D/O - Switch should be set to “O” to for CFLs, which disables the dimming function. Flip to “D” for
incandescent and other dimmable bulbs.
Learn - Syncs remote control to receiver. The remote was synced at the factory. Should it become necessary to
re-sync the remote. Turn off the main power, then turn it back on. Within 30 seconds, use a small screwdriver to
press and hold the learn button on the remote for 3 seconds. The fan will turn on and light (if applicable) will blink
three times, signaling a successful synchronization.
Questions? Call our customer service department
at 1-800-643-0067, 8 a.m. - 5 p.m., EST, Friday. Remote
Qty. 1
Wall Bracket
Qty. 1
Battery
Qty. 2
Receiver
Qty. 1
Wire
Connector
Qty. 3
Mounting
Screw
Qty. 2
Model : TR121B
CAUTION:
To assure continued FCC compliance:
FCC ID：KUJCE10410
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any changes or modifications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.