Chungear Co CE10603 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

DC POWER CEILING FAN REMOTE CONTROL MANUALLEARNING PROCESSNOTE: The Hand Held Remote Control System is equipped with a learning frequency function which has codecombinations to prevent potential interference from other remote units.Step:1Open the remote battery cover and install DC12V battery.Step:2Within 30 seconds of turning the Receivers AC power ON.Step: 3 Press and hold remote for over 5 seconds, once the receiver has detected thefrequency, the receiver will make sound, Bi Bi, twice. This will indicate the receiverhas learned the frequency that was previously selected on the transmitter.◆（you need to perform this step when replace blade or learning variable speeddrive）Step: 4 Fan setting : Within 30 seconds of turning the Receivers AC power ON,Pressand hold remote “ ” button about 5~15 seconds, will hear 3 Bi Bi sound,within60 seconds will hear 3 Bi Bi sound means setting is completed.NOTE: After the AC power is on, do not press any other button on the transmitter beforesetting learning. Doing so will cause the procedure to fail.After completing the steps above, you should be able to operate the ceiling fanand light. If the fan is not responding to the transmitter, please turn the power off to the receiver.And repeat step 1 and 2.NOTE: Remove the battery if not used for long periods of time to prevent damage to the hand held remote.FUNCTIONS OF TRANSMITTER1. ：To turn the fan off.2. :Press this button to increasing fan speed and LED indicator would be on the position offanspeed. (1~6 speed)If press this button when fan is off, fan speed memory will changed for increasing one speed.Example：If fan speed is on 1st , press to turn off fan and then press . Next time fan turnon2nd speed.3. :Press this button to decreasing fan speed and LED indicator would be on the position offanspeed.(1~6 speed)If press this button when fan is off, fan speed memory will changed for decreasing one speed.Example：If fan speed is on 6th , press to turn off fan and then press . Next time fan turnon5th speed.4. :To set fan wind direction up or down.5. :“NATURAL FLOW”, press the button for set fan speed change automatically. If fan speedison 1st, 2nd, or 3rd, press this button for low fan speed changing automatically. If fan speed is on4th,5th, or 6th, press this button for high fan speed changing automatically.6. ：To turn on and turn off the light.7. When pressing remote button, the LED indicator on position 1 would be on. If you press remote button and LEDindicator would not be on, you should change new DC12V battery.8. When pressing remote button, the receiver would make sound one time for indicating of getting signal from remotewell.TR180A
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference toradio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect theequipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or anexperienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10603This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devicemay not cause harmful interference, and (2) this device must accept any interference received, including interference thatmay cause undesired operation.

Navigation menu