Chungear Co CE10606 Ceiling Fan Remote Controller (Transmitter) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3747189
Application ID	nSf8+A98m/3MuuFxfIe0jA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	41.3kB (516235 bits)
Date Submitted	2018-02-08 00:00:00
Date Available	2018-02-08 00:00:00
Creation Date	2018-02-08 17:51:51
Producing Software	Microsoft: Print To PDF
Document Lastmod	2018-02-08 17:51:51
Document Title	C:\Users\RD1-Assistant\Desktop\æ‹‚çı—æŒ⁄件\TR269A+MR36T èªªæŸ”æł¸.doc
Document Author:	RD1-Assistant

WALL/COOLTOUCH TRANSMITTER
OPERATION AND INSTALLATION INSTRUCTIONS
IMPORTANT
(Please keep this instruction pamphlet.)
YOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND THE LIGHT KIT
TO THE ON POSITION BEFORE INSTALLING THE REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER:
1. Read and save these instructions.
2. Please note that all fixed wiring appliances should be installed by a qualified electrician.
3. The supply to the remote control receiver should be connected through a mains switch, i.e. existing
wall switch.
4. Disconnect from power supply at wall switch before working on remote control receiver or ceiling fan.
5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.
6. This unit is to be used for the control of ceiling fan and in an AC110/120V 60Hz power supply only.
7. The receiver is acceptable for installation in damp and wet rated fans, but cannot be submerged in
water. The wall transmitter is only to be installed indoors.
8. Do not pull on or cut leads shorter.
9. Do not drop or bump the unit.
10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place
as this will damage the transmitter. Dispose of used battery properly, keep the battery out of reach of
children.
11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable
(rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WILL DAMAGE THIS RECEIVER.
1. Ceiling fan must be set at HIGH speed before installation.
2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The
canopy comes up to cover the receiver and bracket.
AC POWER ON/OFF SWITCH(
): Before installing wall control, slide to “OFF” position. After
installation is complete, slide to “ON” position to begin operation.
Installing Wall Control (TRANSMITTER):
Remove wall plate, disconnect and remove the toggle switch
from wall junction box. Using the wire connectors,
make the electrical connections to the wall control
(transmitter) unit. Carefully push all connected wires
inside wall switch box. Secure wall control unit with
2 screws previously removed. Face plate will snap
onto the transmitter.
ACTIVATING THE LEARNING PROCESS
Note: The Wall Transmitter will need to be programmed first before the hand held remote.
1. After installation is complete, AC power is turned on and
SWITCH is at ON position within 30 seconds,
press and hold the LEARN button for 3 seconds. Fan will
turn on at medium speed and light (if installed) will turn
on. This confirms that the SMART SYNC setting is active
and ok. (FIG. 4)
2. If user cannot finish the setting within the 30 seconds
time frame, the main power must be turned off and
re-started again. This will reset the unit. Repeat step 1
until the LEARNING feature is activated as indicated.
LIGHT FUNCTION SELECT SWITCH
FIG. 4
1. If the ceiling fan has fluorescent lighting, please slide the “light function select switch” to “O” position. If
the ceiling fan has incandescent or halogen lighting or LED, please slide the “light function select
switch” to “D” position. (FIG. 4)
2. Light load: 190W (Max.) If overloaded, the receiver will cut off light power automatically. Please change
the light load.
WALL TRANSMITTER OPERATION (FIG. 5)
FAN OFF :Turn off the ceiling fan.
HI : Turn on the fan at high speed.
MED : Turn on the fan at medium speed.
LOW: Turn on the fan at low speed.
LIGHT: ON/OFF-Turn the light on or off.
DIMMER-Press and hold to dim or
brighten light to the desired level and release.
TR269A
(Incandescent or halogen or LED and light function select switch Or on “D” position.)
REV: Press this button for forward/reverse airflow of ceiling fan. (Optional)
FIG. 5
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult
the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
FCC ID：KUJCE10606
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Warning                         : Info object (51 0 obj) not found at 514870

EXIF Metadata provided by EXIF.tools