Chungear Co CE10616 Ceiling Fan Remote Controller (Transmitter) User Manual

Chungear Industrial Co Ltd Ceiling Fan Remote Controller (Transmitter)

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e.existing wall switch.4. Disconnect from power supply at wall switch before working on remote control receiver orceiling fan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in an AC120V 60Hz power supply only.7. Do not install in damp locations or immerse in water. (For indoor use only.)8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takesplace as this will damage the transmitter. Dispose of used battery properly, and keep thebattery out of reach of children.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with anyvariable (rheostat) wall control.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pressing the “LightSwitch” after installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket.The canopy comes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHTKIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
LEARNING PROCESS1. This unit finished learning process inside manufactory, if replace transmitter or receiver, user need toredo learning process before using this unit. Receiver could remember up to 5pcs transmitter.2. After installing the unit and power on, open battery cover (with battery, DC1.5V/AAA 2pcs, installed) andpress and use a ball pen to hold ”LEARNING” key 1~3seconds, FAN will be turn off and the turn tomedium speed, which indicate that learning process finished. Learning effect distance is same withremote’s. Please note that must press the “LEARNING KEY” within 30sensonds after power on. If justreplace batteries, no need to re-learn.3. Please note that the transmitter can learn in multiple receiver, when doing learning process please makesure not learn in other receiver. Suggest to separate power switches of fans in 2 meter range.LIGHT FUNCTION SELECT SWITCH1. If installed energy light onto ceiling fan, please slide the “light function select switch” to on/offposition. If installed tungsten light onto ceiling fan, please slide the “light function select switch”to dimmer position.2. Light load: 190W (Max.) If overload, the receiver will cut off light power automatically. Please change thelight load.FUNCTIONS OF TRANSMITTERLIGHT : Press and release immediately to turn on or off the light.When light function select switch is on dimmer position, function keysare changed. Press and hold to dim or brighten light to the desiredlevel and release.OFF : Turn off the ceiling fan.HI :Turn on the fan at high speedMED :Turn on the fan at medium speedLOW : Turn on the fan at low speedL. LOW : Turn on the fan at lower speedLEARNING KEYTRANSMITTERInstallation of TransmitterWall Mount Holder with twoscrews.LIGHT FUNCTIONSELECT SWITCHTR92B
To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communications. However, there is noguarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connectthe equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer oran experienced radio/TV technician for help.CAUTION:To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authority tooperate the equipment.FCC ID：KUJCE10616This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Navigation menu